Tripp Lite SRTHERMDUCT Handleiding

Tripp Lite Niet gecategoriseerd SRTHERMDUCT

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SRTHERMDUCT (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Owner’s Manual

SmartRack™ Accessories

Model: SRTHERMDUCT

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Table of Contents

Introduction 2

Parts List 2

Installation 3

Warranty & Warranty Registration 7

201204262-93-2958-EN.indd 1 6/4/2012 2:39:46 PM

Introduction

Tripp Lite’s SRTHERMDUCT is a 3 piece, adjustable venting and cable management system that will t on top of standard 42 or 48U

rack enclosures. The SRTHERMDUCT allows heat built up in a typical rack conguration to be vented upwards into your facility’s return

air duct or other standard ventilation system, helping your equipment perform at its peak while reducing your facility’s cooling and

energy costs.

Parts List

Cable Access Panel (1) Chimney Base (1) Adjustable Chimney

Slider (1)

Enclosure Bottom

Panel (1)

Rectangular

252mm x 476mm

Magnetic Vinyl Sheet

(6)

Cutout 252mm x

476mm x 325mm

Magnetic Vinyl Sheet

(1)

Cutout 252mm x

476mm x 452mm

Magnetic Vinyl Sheet

(1)

Rectangular 252mm x

137mm Magnetic Vinyl

Sheet (4) (48U rack

enclosures only)

M8 Screws (4) M4 Screws (4) M4 Nuts (16)

Tubular Door Seal Flat Door Seal

Rectangular 252mm x

68mm Magnetic Vinyl

Sheet (4) (45U rack

enclosures only)

201204262-93-2958-EN.indd 2 6/4/2012 2:39:48 PM

3 4

Assembling the Chimney Base

1 Position the 4 side panels of the Chimney Base in accordance

with Diagram 1 and secure the attachments with 8 of the M4

nuts that screw onto the pre-installed threaded posts.

Once assembled, this piece can be put aside for later use.

Installation

Assembling the Adjustable Chimney Slider

2 Position the 4 side panels of the Adjustable Chimney Slider

in accordance with Diagram 2 and secure the attachments

with the remaining 8 M4 nuts that screw onto the pre-installed

threaded posts.

Once both the Chimney Base and Slider have been assembled

you can move on to stacking.

Stacking the Chimney

3 With both the Chimney Base and Adjustable Chimney Slider

assembled, position and ﬁt the slider on top of the base.

4 The holes in the sides of the Chimney Base and locking pins

in the sides of the Chimney Slider allow the chimney to be

adjustable in height with a range of 20” (ﬂat, no height) to

34” (adjusted, full height). For installation purposes, it is

recommended to initially stack the two pieces in the 20” (ﬂat,

no height) position until installed on the rack enclosure. To do

so, pull out the four locking pins and slide the Chimney Slider

all the way down over the Chimney Base into the 20” position

as seen in Diagrams 3 and 4.

201204262-93-2958-EN.indd 3 6/4/2012 2:39:49 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SRTHERMDUCT
Kleur van het product:	Zwart
Gewicht:	14510 g
Breedte:	594.1 mm
Diepte:	946.4 mm
Hoogte:	876.3 mm
Gewicht verpakking:	30390 g
Breedte verpakking:	599.9 mm
Diepte verpakking:	1210.1 mm
Hoogte verpakking:	370.1 mm
Land van herkomst:	China
(Buitenste) hoofdverpakking hoogte:	370.1 mm
(Buitenste) hoofdverpakking breedte:	599.9 mm
(Buitenste) hoofdverpakking brutogewicht:	30390 g
(Buitenste) hoofdverpakking lengte:	1210.1 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Code geharmoniseerd systeem (HS):	7326.90.8688