Tripp Lite SRGROUND Handleiding

Tripp Lite Niet gecategoriseerd SRGROUND

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SRGROUND (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16

Owner’s Manual

Copper Bus Grounding Bar

Models: SRGROUND, SRGROUND25

WARRANTY REGISTRATION

automatically entered to win an ISOBAR®

surge protector in our monthly drawing!

tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

Español 6 • Français 11

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of this product. Failure to comply

may invalidate the warranty.

• The instructions in this manual are for common rack and rack enclosure types and may not be appropriate for all mounting applications.

You must determine the ﬁtness of hardware and procedures before mounting.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life

support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

Introduction

The SRGROUND and SRGROUND25 grounding bar are comprised of a thin strip of copper that attaches to standard EIA-310-D rack enclosures

or open frame racks to provide convenient ground contact for standard rack-mount equipment. The SRGROUND ﬁts into 42U or 48U racks or

enclosures. The SRGROUND25 ﬁts into standard 24U or 25U racks or enclosures.

Parts List

45” (1.1 m) Grounding Bar

(with attached grounding lug)

Mounting Buttons

(x2)

Grounding Straps

(x13)

M4 Self

Tapping

Screws (x2)

M4 Screws

(x13)

Washers

(x13)

Cage

Nuts

(x2)

M6x12

Screws

(x2)

7’ (2.1 m) Grounding Bar

(with attached grounding lug)

Mounting Buttons

(x3)

Grounding Straps

(x21)

M4 Self-Tapping

Screws (x3)

M4 Screws

(x21)

Washers

(x21)

SRGROUNDSRGROUND25

42U

Installation

Rack Enclosures

1 , such as Tripp Lite’s SR42UB, attach the For a 42U enclosure

SRGROUND to the 3 indexed horizontal beams at the top, middle

and bottom of the enclosure. The included M4 Self-Tapping

Screws will go through the three clearance holes (non-threaded)

on the bar, and then into the beams of the rack enclosure.

, such as Tripp Lite’s SR48UB, attach the For a 48U enclosure

SRGROUND to the top and middle horizontal beams only, as the

bar will not reach all the way down to the bottom beam.

, such as Tripp Lite’s SR25UB, attach the For a 25U enclosure

SRGROUND25 to the 2 indexed horizontal beams at the top

and bottom of the enclosure, using the top and second from

the bottom holes. The included M4 Self-Tapping Screws will go

through the two clearance holes (non-threaded) on the bar, then

into the beams of the rack enclosure.

, such as Tripp Lite’s SR24UB, attach For a 24U enclosure

the SRGROUND25 to cage nuts installed in the top and bottom

horizontal rails of the enclosure using the top and bottom holes

of the SRGROUND25.

Note: The instructions above are speciﬁc for mounting in Tripp Lite SR42UB,

SR48UB, SR24UB or SR25UB SmartRack™ Enclosures. Mounting in other

enclosure brands is possible, but will vary depending upon the application.

Several holes are provided along the grounding bar that will allow for a workable

installation into any brand’s rack conﬁguration.

Note: Placement will vary and depend on your particular rack conﬁguration. It is

recommended to measure the distance between the bar and your equipment to

accommodate the length of the Grounding Straps. Once the length you need has

been determined, attach the bar in the appropriate holes in the horizontal beams.

2 Attach one end of the Grounding Strap to the bar using the

included M4 screws and washers.

3 Attach the other end of the Grounding Strap to the grounding

provision on the intended equipment.

4 Finally, attach your facility’s system ground to the grounding lug at

the bottom of the bar. The lug can accommodate 2/0-14AWG wires. FACILITY GROUND

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SRGROUND
Kleur van het product:	Black, Brown
Gewicht:	1810 g
Breedte:	15.9 mm
Diepte:	6.4 mm
Hoogte:	1917.7 mm
Gewicht verpakking:	2490 g
Breedte verpakking:	91.4 mm
Diepte verpakking:	1993.9 mm
Hoogte verpakking:	61 mm
Land van herkomst:	China
Duurzaamheidscertificaten:	RoHS
(Buitenste) hoofdverpakking hoogte:	139.7 mm
(Buitenste) hoofdverpakking breedte:	292.1 mm
(Buitenste) hoofdverpakking brutogewicht:	16280 g
(Buitenste) hoofdverpakking lengte:	2006.6 mm
Hoeveelheid per (buitenste) hoofdverpakking:	6 stuk(s)
Code geharmoniseerd systeem (HS):	85389099
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332154818