Tripp Lite Protect It! TLP606B Handleiding

Tripp Lite Niet gecategoriseerd Protect It! TLP606B

Lees hieronder de đź“– handleiding in het Nederlandse voor Tripp Lite Protect It! TLP606B (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
1
Owner’s Manual
Protect It!®
Surge Protectors
Important Safety Instructions 2
Installation 2
Warranty and Product Registration 3
Ultimate Lifetime Insurance Policy 4
Español 5
Français 9
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved. Protect It!
® is a trademark of Tripp Lite.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
18-08-292-932666.indb 1 9/12/2018 9:32:14 AM
2
SAVE THESE INSTRUCTIONS
CAUTION! DO NOT connect to an ungrounded outlet. DO NOT use with 2-wire extension
cords or adapters. This surge protector is designed for indoor use only. Install the
surge protector away from heat-emitting appliances such as radiators or heat
registers. Do not install where excessive moisture is present. Do not plug extension
cords into it. Never install electrical, telephone, network or coaxial wiring during a
lightning storm. Do not drill into any part of the housing or open the housing for any
reason. There are no user-serviceable parts inside.
Important Safety Instructions
Installation
• Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended.
Mount Your Surge Protector (Optional Installation. Available on Select Models Only): If
desired, mount your surge protector on a wall or other sturdy, vertical surface. However, you
must mount the surge protector prior to connecting your equipment. Place a sheet of paper over
the surge protector’s mounting holes and mark their centers with a push pin. Next, place this
template over the desired area and mark with the push pins. Install screws (user supplied) into
the marks until ÂĽ in. (0.6 cm) of the screw heads are exposed. Mount the surge protector over
the screw heads and slide into place.
Connect Your Surge Protector to the AC Power Line: Plug the surge protector’s power cord
into a standard 3-wire grounded 120V AC outlet.
Turn Your Surge Protector ON: Press the surge protector’s power switch to “ON” or “RESET”
(depending on model). Select models feature an illuminated switch.
Check Your Surge Protector’s Diagnostic Indicator Lights (Available on Select Models
Only): If your surge protector features diagnostic LEDs, check them prior to connecting your
equipment. They will indicate various operating conditions when the surge protector is plugged
into a live 120V AC outlet and the surge protector’s power switch is on.
“PROTECTED” LED: Indicates the surge suppression components are intact and providing
complete protection against surges. If this LED does not illuminate, some of the surge
suppression components are not functioning, and the unit should be replaced.
Visit www.tripplite.com/support.
“GROUNDED” LED: Indicates wall outlet is grounded and surge protection can properly
function. If this light DOES NOT illuminate and power is present, consult a qualified electrician
to examine your outlet’s wiring.
“LINE OK” LED (select models): Indicates 120V AC power is present with no wiring faults
detected.
Connect Your Equipment to the Surge Protector’s AC Outlets: Plug your equipment’s power
cords (including 2-wire devices) into the surge protector’s AC outlets. Select models feature
integrated safety covers which cover the outlets when not in use. Other models feature special
widely-spaced outlets to accommodate transformers without covering other outlets. DO NOT plug
in extension cords. DO NOT OVERLOAD the surge protector’s outlets. The surge protector can
accommodate a total equipment load of up to 15 amps (whether plugged into a single outlet or
spread out over multiple outlets). If the load on the surge protector exceeds 15 amps, the circuit
breaker* will trip and the outlets will stop providing power. If the circuit breaker trips, reduce the
load by unplugging some devices. Depress the circuit breaker to reset.
* Circuit breakers are integrated into the power switch on select models and offered as a separate feature on other models.
18-08-292-932666.indb 2 9/12/2018 9:32:14 AM
3
Installation
USB Charging Ports: USB charging ports are capable of delivering ample power to even the
most demanding devices, including smartphones, tablets, MP3 players, etc. Total USB charging
output varies by model.
Connect Your Equipment to the Surge Protector’s Phone Jacks (Optional Installation.
Available on Select Models Only): Connect a phone cable from the wall jack directly to the
surge protector’s RJ-style phone jack labeled “IN.” Connect a phone cable from the surge
protector’s RJ-style phone jack labeled “OUT” directly to the device to be protected. Select
models feature two “OUT” jacks; either one or both of the jacks may be used, but protection is
for a device or devices sharing a single line only. All models with phone line surge protection,
except the TLP810NET, protect devices on a single line only. TLP810NET models feature a single
set of RJ-style phone jacks which protect devices on two lines. The surge protector must always
be the first item connected in line from the wall jack. The surge protector must be plugged into
a 3-wire grounded AC outlet for phone line surge protection to work.
Connect Your Equipment to the Surge Protector’s Network Jacks* (Optional Installation.
Available on Select Models Only): Connect a data cord from the wall jack or cable/DSL
modem directly to the surge protector’s network jack labeled “IN.” Connect a data cord from the
surge protector’s network jack labeled “OUT” directly to the device to be protected (typically a
computer’s network interface card).
The surge protector must always be the first item connected in line from the Ethernet source
(typically a wall jack). The surge protector must be plugged into a 3-wire grounded AC outlet for
network line surge protection to work.
Connect Your Equipment to the Surge Protector’s Coaxial Jacks (Optional Installation.
Available on Select Models Only): Connect a coaxial cable from the wall jack directly to the
surge protector’s “F” style coaxial jack labeled “IN.” Connect a coaxial cable from the surge
protector’s “F” style coaxial jack labeled “OUT” directly to the device to be protected. Select
models include a second set of coaxial jacks for simultaneous connection and protection of
devices on two separate lines (cable, antenna or satellite). The surge protector must always be
the first item connected in line from the coaxial wall jack. The surge protector must be plugged
into a 3-wire grounded AC outlet for coaxial line surge protection to work.
* 10/100 BaseT/TX, Token Ring. Not compatible with PoE (Power Over Ethernet) applications.
Warranty and Product Registration
Lifetime Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and
workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair
or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the
product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th St., Chicago, IL 60609. Seller will pay return
shipping charges.
The warranties of all TRIPP LITE surge protectors are null and void if they have been connected to the output of any UPS system.
The warranties of all TRIPP LITE UPS Systems are null and void if a surge protector has been connected to its output receptacles.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR
NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY
OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY
EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied
warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which
vary from jurisdiction to jurisdiction.)
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the
use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty
as to the suitability or fitness of these devices for any specific application.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a drawing for a
chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
18-08-292-932666.indb 3 9/12/2018 9:32:14 AM


Product specificaties

Merk: Tripp Lite
Categorie: Niet gecategoriseerd
Model: Protect It! TLP606B

Heb je hulp nodig?

Als je hulp nodig hebt met Tripp Lite Protect It! TLP606B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Tripp Lite

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd