Tripp Lite Basic PDUH30HV Handleiding

Tripp Lite Stekkerdoos Basic PDUH30HV

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite Basic PDUH30HV (12 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12

Basic Rack PDU

Important Safety Instructions 2

Important Warnings 2

Installation 3

Features 4

Warranty & Product Registration 4

Español 5

Français 9

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PDUH30HV19

(Series Number: AG-00E6)

PDUH32HV19

(Series Number: AG-00E5)

PDUH30HV

(Series Number: AG-00E6)

PDUH32HV

(Series Number: AG-00E5)

14-09-039-9333BC.indb 1 9/29/2014 12:33:52 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed

during the installation, operation and storage of this product. Failure to

heed these instructions and warnings will void the product warranty.

Important Warnings

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended. Do not use this equipment in the presence of a

flammable anesthetic mixture with air, oxygen or nitrous oxide.

14-09-039-9333BC.indb 2 9/29/2014 12:33:52 PM

Installation

Note: The illustrations may differ somewhat from

your PDU model.

1 The Determine Installation Configuration.

PDU supports four primary installation

configurations: 1U Rack, 0U Rack, Wall and

Under-Counter. Choose a configuration and

follow the installation instructions in the

appropriate section of Step 1 before

proceeding to Step 2.

Note: Regardless of installation configuration,

the user must determine the fitness of

hardware and procedures before mounting.

The PDU and included hardware are designed

for common rack and rack enclosure types

and may not be appropriate for all

applications. Exact mounting configurations

may vary.

1-1 1U Rack Installation. Attach the PDU to the

rack by inserting four user-supplied screws (A)

through the PDU mounting brackets ( ) and B

into the mounting holes of the rack rail as

shown.

1-2 Remove the 0U Rack Installation. Part 1:

screws ( ) attaching the mounting brackets to C

the PDU, change the orientation of the

brackets as shown and reattach the brackets.

Use only the screws supplied by the

manufacturer or their exact equivalent

(#6-32, 1/4” flat head). Attach the Part 2:

PDU vertically by inserting two or more user-

supplied screws ( ) through the PDU mounting A

brackets ( ) and into mounting points in the B

rack or rack enclosure.

1-3 After repeating Part 1 Wall Installation.

above, attach the PDU to a stable mounting

surface by inserting two or more user-supplied

screws ( ) through the PDU mounting brackets A

(B) and into secure mounting points on the

mounting surface.

1-4 After repeating Under-Counter Installation.

Part 1 above, attach the PDU to a stable

mounting surface by inserting four user-

supplied screws ( ) through the PDU mounting A

brackets ( ) and into secure mounting points B

on the mounting surface.

2 Attach the input plug of the PDU to a grounded outlet. Insert the plug directly into a

grounded outlet that does not share a circuit with a heavy electrical load (such as an air

conditioner or refrigerator).

3 Attach equipment to the PDU. Do not exceed the load rating of the PDU. The total electrical

current used by the PDU will be displayed on the digital meter in amperes.

1-1

1-2

1-3

1-4

Step 1

14-09-039-9333BC.indb 3 9/29/2014 12:33:54 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Stekkerdoos
Model:	Basic PDUH30HV
Kleur van het product:	Zwart
Gewicht:	3510 g
Breedte:	439.4 mm
Diepte:	95.2 mm
Hoogte:	43.2 mm
Snoerlengte:	3.66 m
Gewicht verpakking:	3850 g
Breedte verpakking:	514.4 mm
Diepte verpakking:	285.8 mm
Hoogte verpakking:	76.2 mm
Soort:	Eenfasig
Gebruikershandleiding:	Ja
Materiaal behuizing:	Metaal
Land van herkomst:	China
Afmetingen verpakking (BxDxH):	514.4 x 285.8 x 76.2 mm
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-15 - 50 °C
Spanning:	200 - 240 V
Bedrijfstemperatuur, bereik:	5 - 122 °F
Hoogte, in bedrijf:	0 - 3000 m
Afmetingen (B x D x H):	439 x 95.3 x 43 mm
Montage:	Horizontaal/Verticaal
Stekker:	NEMA L6-30P
(Buitenste) hoofdverpakking hoogte:	304.8 mm
(Buitenste) hoofdverpakking breedte:	508 mm
(Buitenste) hoofdverpakking brutogewicht:	17990 g
(Buitenste) hoofdverpakking lengte:	533.4 mm
Hoeveelheid per (buitenste) hoofdverpakking:	5 stuk(s)
Rackcapaciteit:	0U/1U
AC-ingangsfrequentie:	50 - 60 Hz
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332183214
Aantal AC uitgangen:	10 AC-uitgang(en)
Nominale input voltage:	200 - 240 V
Stopcontacttypes:	C13 stekker
Stroom (max.):	30 A
PDU types:	Basis
Spanningsbeveiliging:	Ja