Traulsen TS066HT Handleiding
Traulsen
Niet gecategoriseerd
TS066HT
Lees hieronder de 📖 handleiding in het Nederlandse voor Traulsen TS066HT (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 3.5 gebruikers gemiddeld met 4.6 sterren beoordeeld
Pagina 1/20
This Traulsen unit is built to our highest quality standards. We build our refrigerators this way as a matter of pride. This philosophy has made Traulsen the
leader in commercial refrigeration since 1938. We thank you for your choice and confidence in Traulsen equipment and we know you will receive many years
of utility from this equipment.
All Traulsen units are placed on a permanent record file with the service department. In the event of any future questions you may have, please refer to the model
and serial number found on the name tag affixed to the unit. Should you need service, call us on our toll free number, 800-825-8220 between 7:30 am - 4:30
pm CST, Monday thru Friday. You may also log onto www.traulsen.com for further information. It is our pleasure to help and assist you in every possible way.
OWNER’S MANUAL
Instructions for the installation, operation
and maintenance of Traulsen:
FORM NUMBER TR35921 REV. 11/10 P/N 375-60308-00
Quality Refrigeration
INSTALLER
COMPLETE THE FOLLOWING INFORMATION PRIOR TO UNIT INSTALLATION
INITIAL START DATE: SERIAL NO.
MODEL TYPE:
COMPANY/INDIVIDUAL NAME:
INSTALLER:
TS Series Pizza/Salad/Sandwich Prep Tables
TS048HT, TS066HT, TS072HT & TS090HT
TABLE OF CONTENTS
I. THE SERIAL TAG
I. a - SERIAL TAG:
The serial tag is a permanently affixed label on which is recorded vital
electrical and refrigeration data about your Traulsen product, as well
as the model and serial number. This tag is located in the right interior
compartment on all standard TS Series models.
READING THE SERIAL TAG
• Serial = The permanent ID# of your Traulsen unit
• Model = The model # of your Traulsen unit
• Volts = Voltage
• Hz = Cycle
• PH = Phase
• Total Current = Maximum amp draw
• Minimum Circuit = Minimum circuit ampacity
• Lights = Light wattage
• Heaters = Heater amperage (Hot Food units only)
• Refrigerant = Refrigerant type used and refrigerant charge
• Design Pressure = High & low side operating pressures
• Agency Labels = Designates agency listings
-1-
e-Enter The Service Access Page 7
f-Customer/Service Parameters Page 7
g-Adjusting Thermostat Set Point Page 8
h-Adjusting Thermostat Set Point Differential Page 8
i-Changing The Temperature Scale Page 8
j-Setting The 24-Hour Clock Page 8
k-Setting The Date Page 9
l-Setting Daylight Savings Time Page 9
m-Starting A Manual Defrost Cycle Page 10
n-Setting Defrost Lockouts Page 10
o-Adjusting The Room Temperature Offset Page 11
p-Viewing Sensor Temperatures Page 11
VIII. WIRING DIAGRAM Page 12
IX. TROUBLE SHOOTING GUIDE Page 13
X. SERVICE ASSISTANCE
a-Service Information Page 14
b-Service Support Information Page 14
c-Warranty Registration Page 14
XI. WARRANTIES Page 15
XII. SERVICE PARTS LIST Page 16
I. THE SERIAL TAG Page 1
II. RECEIPT INSPECTION Page 2
III. OPERTIONAL GUIDELINES Page 2
IV. INSTALLATION
a-Location Page 2
b-Packaging Page 2
c-Installing/Adjusting Legs orCasters Page 2
d-Doors Page 2
e-Installing Optional Drawers Page 2
f-Cord & Plug Page 2
g-Power Supply Page 3
V. DAILY OPERATION
a-Pans Page 3
b-Setting Up The Rail Page 3
c-Closing Down The Rail At Night Page 3
d-Defrost Page 3
VI. CARE & MAINTENANCE
a-Cleaning The Condenser/Filter Page 4
b-Replacing The Gaskets Page 4
c-Cleaning The Cabinet Surfaces Page 4
d-Cleaning The Rail Area Page 4
VII. MICROPROCESSOR CONTROL
a-Control Features Page 5
b-Alarm Explanations Page 6
c-Control Panel Diagram Page 7
d-Notes To The User Page 7
FORT WORTH, TX.
SERIAL MODEL
VOLTS Hz PH
TOTAL CURRENT AMPS
MINIMUM CIRCUIT AMPS
MAXIMUM OVERCURRENT PROTECTION AMPS
LIGHTS WATTS
HEATERS AMPS
REFRIGERANT TYPE OZ
DESIGN PRESSURE HIGH LOW
REFRIGERANT TYPE OZ
DESIGN PRESSURE HIGH LOW
370-60294-00 REV (A)
COMMERCIAL REFRIGERATION
-2-
II. RECEIPT INSPECTION
II. a - RECEIPT INSPECTION:
All Traulsen products are factory tested for performance and are free
from defects when shipped. The utmost care has been taken in crating
this product to protect against damage in transit.
You should carefully inspect your unit for damage during delivery. If
damage is detected, you should save all the crating materials and
make note on the carrier’s Bill Of Lading describing the damage. A
freight claim should be filed immediately. If damage is subsequently
noted during or immediately after installation, contact our customer
care team to le a freight claim. There is a fteen (15) day limit to le
freight damage with the carrier. Under no condition may a damaged
unit be returned to Traulsen without first obtaining written permission
(return authorization). You may contact Hobart/Traulsen customer care
at 800-333-7447 to request a return or file a claim.
III. OPERATIONAL GUIDELINES
III. a - OPERATIONAL GUIDELINES:
Follow these simple guidelines for proper TS Series Operation.
1. Keep the condenser clean. Don’t obstruct airflow.
2. Use up to 6” deep stainless steel or aluminum pans.
3. All pan spaces should be filled any time the unit is running, even if
some pans are empty.
4. Keep the room temperature at 86
0
F (30
0
C) or less.
5. Do not allow air drafts (such as heat, A/C or ventilation) to blow on
or over the rail area. This will disrupt the air blanket over the product
area, resulting in poor holding temperatures.
6. Rail covers should be closed over the rail as much as possible.
7. Product should be loaded into the rail at a maximum temperature of
36
0
F. The TS Series unit was not designed to chill warm product, but
to hold refrigerated product at a safe temperature.
8. Keep area around the evaporator fans clear.
IV. INSTALLATION
IV. a - LOCATION:
Select a proper location for your unit, away from extreme heat or cold.
Allow enough clearance between the unit and the side wall in order to
make use of the door stay open feature at 120
0
(self-closing feature
operates up to 90
0
). The door(s) must be able to open a minimum of
90
0
in order to make use of the maximum clear door width.
IV. b - PACKAGING:
Your Traulsen unit is shipped from the factory bolted to a sturdy wooden
pallet in stretch wrapped material and wood crate.
Most exterior stainless steel surfaces have a protective vinyl covering to
prevent scratching during manufacturing, shipping and installation.
After the unit is installed in place of application peel, remove and discard
the covering from all surfaces.
IV. INSTALLATION (CONTINUED)
IV. b - PACKAGING (continued):
To remove the wooden pallet, first if at all possible, we suggest that the cabinet
remain bolted to the pallet during all transportation to the point of final installation.
The bolts can then be removed with a 1/2” socket wrench. Avoid laying the unit
on its front, side or back for removal of the pallet.
NOTE: Traulsen does not recommend laying the unit on its front, side or
back. If you must, please allow the unit to remain in an upright position
for 24 hours before plugging it in so that the compressor oils and refriger-
ant may settle.
IV. c - INSTALLING/ADJUSTING LEGS OR CASTERS:
To install legs or casters, slide leg or caster into the caster channel from the side
of the unit without the refrigeration system.
To adjust the legs or casters, loosen the two bolts and move leg or caster to desired
location, spacing between leg or caster not to exceed 48 inches. Leg or caster on
each end of the unit can not exceed 8 inches from the end of the cabinet.
NOTE: Traulsen recommends to position legs or casters under the mullion
when possible.
IV. d - DOORS:
Your Traulsen TS Series model door(s) are eld re-hingeable. If re-hinging is
required, please contact our in-house service department at 800-825-8220 for
re-hinging instructions.
IV. e - INSTALLING OPTIONAL DRAWERS:
Doors are supplied standard on all TS Series models. However, we have engineered
our refrigerator models with a drop-in feature that allows you to easily convert
door(s) into two 6” deep drawers or three 4” deep drawers.
The door(s) on the refrigerator models can easily be converted to drawers in the
field. To begin the process, open the door to its maximum position. Support the
non-hinged end of the door so minimum movement occurs. When the bolts from
the lower hinge plate are removed, remove the lower hinge plate and then the door
from the top hinge bracket plate and then the door from the top hinge bracket.
The hinge plate pin and plastic bushing will remain in the top hinge plate.
NOTE: The lower hinge plate is under spring tension.
Product specificaties
| Merk: | Traulsen |
| Categorie: | Niet gecategoriseerd |
| Model: | TS066HT |
Heb je hulp nodig?
Als je hulp nodig hebt met Traulsen TS066HT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Traulsen
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
Handleiding Niet gecategoriseerd
- Niet gecategoriseerd Metapace
- Niet gecategoriseerd P3 International
- Niet gecategoriseerd Indesit
- Niet gecategoriseerd Maxicool
- Niet gecategoriseerd Dawn House
- Niet gecategoriseerd UClear
- Niet gecategoriseerd Consul
- Niet gecategoriseerd BabyOno
- Niet gecategoriseerd Texas Instruments
- Niet gecategoriseerd BlaknBlu
- Niet gecategoriseerd Jan Nowak
- Niet gecategoriseerd AVMATRIX
- Niet gecategoriseerd ShelterLogic
- Niet gecategoriseerd Taylor
- Niet gecategoriseerd TRIUS
Nieuwste handleidingen voor Niet gecategoriseerd
12 Juni 2025
12 Juni 2025
12 Juni 2025
12 Juni 2025
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025