TP Link Tapo S200D Handleiding

TP Link Smarth home Tapo S200D

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link Tapo S200D (2 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 76 personen en werd door 38.5 gebruikers gemiddeld met 4.9 sterren beoordeeld

Download PDF

Pagina 1/2

Product Introduction Wire Your Switch

Tapo smart dimmer switch turns on and

dims the lights automatically, saving you

eort and electricity bills.

Connect the wires to the smart dimmer

switch as shown below.

Disconnect the wires from the old switch.

Ground: Usually green or copper.

Neutral: Usually white and not connected to the dumb switch.

Line: Usually black and coming from the circuit breaker.

Load: Usually black. One end is connected to the light.

If you are unsure, consult a qualied electrician.

Turn o the circuit breaker. Then remove

the old wallplate of the wall switch and

label the wires.Ground and Neutral

Identify and Line Load wires.

3Line up the switch with the mounting

holes. Secure it with screws.

5Attach the wallplate and turn on the

circuit breaker. Then the wiring is

nished.

Flip the page over to complete setup.

1) Turn on the circuit breaker. Use a voltage detector

to identify the energized wire (Line wire).

2) and Turn o the circuit breaker. Label the Line Load

wires.

Take care to avoid electric shocks.

Load wireLine wire Power

Source

To Light

Button Explanations

Smart Wi-Fi Dimmer Switch

Quick Start Guide

Specications

Rating: 120 V~ 60 Hz

Load: 300 W Incandescent, 150 W LED

Operation temperature: 0~40 ℃

Method of mounting included: Independently mounted

(Vertically position only);

Operating control, Type 1 action

Pollution Degree 2, Rated Impulse Voltage 2500 V

Software Class A, NEMA Type 1.Y

*Images may dier from your actual product.

Restart

Reset

Press and hold for about 5s to reset

Wi-Fi while keeping other settings.

Press to restart your switch.

Decrease or increase the brightness.

Press and hold for about 10s to restore

your switch to factory default settings.

Set Up Your Switch Appearance

STEP 2 SET UP

Tap the button in the app. Select Switches

and then your model. Follow the step-by-step

app instructions to set up your smart switch.

DOWNLOAD APP

Get the Tapo app from the App Store or

Google Play.

STE 1P

Before installing, servicing or removing the switch, read and follow all safety

precautions including the following:

• CAUTION – Risk of Electric Shock – More than one disconnect switch may

be required to de-energize the equipment before servicing. A circuit

breaker which disconnects the Line and Neutral conductor simultaneously

is suitable. Ensure power is o at the circuit breaker before removing or

installing any switch. Use a non-contact voltage tester to ensure the power

is o.

• The Smart Switch must be installed and used in accordance with the

National Electric Code (NEC) or your local electrical code. If you are

unfamiliar with these codes and requirements, or are uncomfortable

performing the installation, consult a qualied electrician.

• Do not install the Smart Switch with wet hands or when standing on wet or

damp surfaces.

• Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95

in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).

• Tighten terminal screws to 13 lbf-in.

On/O

Button

Decrease/Increase

Brightness

Restart

LED

Reset

Brightness

Indicators

Need some help?

Visit www.tp-link.com/support

for technical support, user guides, FAQs,

warranty and more information.

Safety Notice

Haute tension. Débrancher l'alimentation électrique avant

d'utiliser

High Voltage-Disconnect power supply before servicing

CAUTION

MISE EN GARDE

LED Status

Starting up; disconnected

from cloud.

Solid amber

Blinking amber

Blinking green

White

Solid red

Stay green for 30s

Blinking amber & green

Connecting to Wi-Fi.

Ready for setup.

Device resetting.

Light fixture is off.

Disconnected from Wi-Fi.

Connected to Wi-Fi.

Blinking green slowly Firmware upgrading.

Product specificaties

Merk:	TP Link
Categorie:	Smarth home
Model:	Tapo S200D
Soort bediening:	Buttons, Rotary
Kleur van het product:	Wit
Breedte:	86 mm
Diepte:	23.7 mm
Hoogte:	86 mm
Soort:	Slimme dimmer
Stroombron:	Batterij/Accu
Type verpakking:	Doos
Kastontwerp:	Extern
Frequentie:	886 - 922 MHz
Dimbaar:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Type batterij:	CR2032