TP Link LiteWave LS105GP Handleiding
TP Link
Schakelaar
LiteWave LS105GP
Bekijk gratis de handleiding van TP Link LiteWave LS105GP (2 pagina’s), behorend tot de categorie Schakelaar. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.9 sterren uit 3 reviews. Heb je een vraag over TP Link LiteWave LS105GP of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
Installation Guide
Gigabit Desktop PoE+ Switch
© 2023 TP-Link 7106510517 REV1.0.1
Switches Explanation
O: Ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.
On: Ports run at 10 Mbps and support PoE power supply up to 250 m away.
Extend (For LS105GP/LS108GP/LS1210GP)
Connection
Note: For simplicity, we will take LS1210GP for example throughout the Guide.
PC
Router
LAN Port WAN Port
Internet
DC P er Adapterow
AC Power Cord
Note:
PoE ports can also connect to non-PoE devices, but only transmit data.
LS1210GP has two uplink ports, which typically connect to uplink devices like routers.
The SFP slot of LS1210GP needs to work with a gigabit SFP module.
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD).
When the switch nds that the PD works abnormally, the switch will reboot it.
Recovery (For LS105GP/LS108GP/LS1210GP)
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend (Port 1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
O: Ports can transmit data with each other.
On: Specic ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink ports.
Isolation (For LS1210GP)
PoE Ports (1-8)
IP Camera AP IP Phone
PoE Devices
1.
2.
3.
LS105GP/LS108GP/LS1210GP
LS1210GP
LED Explanation
PoE Status
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
Power
On: Power on
O: Power o
Link/Act; Uplink 1, Uplink 2
On:
Running at 10/100/1000 Mbps, but no activity.
Flashing:
Running at Mbps and is 10/100/1000
transmitting or receiving data.
O:
No device is linked to the corresponding port.
PoE Max
For LS105GP:
On: 58 W≤Total power supply < 65 W
Flashing: Total power supply ≥ 65 W
O: Total power supply < 58 W
For LS108GP:
On: 55 W≤Total power supply < 62 W
Flashing: Total power supply ≥ 62 W
O: Total power supply < 55 W
For LS1210GP:
On: 54 W≤Total power supply < 61 W
Flashing: Total power supply ≥ 61 W
O: Total power supply < 54 W
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please
contact us.
Place the device with its bottom surface downward.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/support/ce/
EU declaration of conformity
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 C (32˚C to 40˚ ˚F to 104˚F)
-40˚ ˚C (-40˚C to 70 F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and
Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at
https://www.tp-link.com/support/ukca
The plug on the power supply cord is used as the disconnect device, the socket-outlet
shall be easily accessible.
Specications
General Specications
IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x,
IEEE 802.3af, IEEE 802.3at, IEEE 802.1p
LS105GP:
5 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;
PoE Ports: Port 1-4
LS108GP:
8 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;
PoE Ports: Port 1-8
LS1210GP:
9 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;
1 1000 Mbps SFP port;
PoE Ports: Port 1-8
10BASE-T: UTP category 3, 4, 5 cable (maximum ); 100 m
EIA/TIA-568 100 Ω STP (maximum 100 m)
100BASE-TX: UTP
category
5, 5e
cable (maximum
100
m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
1000BASE-T: UTP
category 5e cable or above (maximum 100 m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
LS105GP: 10 Gbps
LS108GP: 16 Gbps
LS1210GP: 20 Gbps
Store-and-Forward
Automatically learning, automatically aging
Input: 100-240 VAC, 50/60 Hz
Output: 53.5 V DC/1.31 A
LS105GP: 65 W (up to 30 W for each PoE port)
LS108GP: 62 W (up to 30 W for each PoE port)
LS1210GP: 61 W (up to 30 W for each PoE port)
Yes
LS105GP: 76 mm
LS108GP: 65 mm
LS1210GP: 150 mm
Standard
Interface
Switching Capacity
Network Media (Cable)
Power Supply
MAC Address Learning
Transfer Method
PoE Budget
Distance Between
Mounting Holes
Wall Mountable
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power LED is
not lit, please check as follows:
A1:
Make sure the AC power cord is connected the switch with power source properly.
A2:
Make sure the voltage of the power supply meets the requirements of the input voltage
of the switch.
A3:
Make sure the power source is on.
Q1. The Power LED is not lit.
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are rmly plugged into the switch and the device.
A2:
Make sure the connected device is turned on and working well.
A3:
The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it
should be less than 250 meters (820 feet).
Q2. Why is the Link/Act LED not lit while a device is connected to
the corresponding port?
Q3. Why is the PoE Port not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the maximum, the
PoE port with a smaller port number has a higher priority. The system will cut o power to
the ports with larger port numbers to ensure supplying to other ports.
Take LS1210GP as an example. If port 1, 2 and 4 are consuming 15.4 W respectively, and
an additional PoE device with 20 W is connected to port 3, the system will cut o the power
of port 4 to compensate for the overload.
A1:
Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to
avoid the PD’s damage.
A2:
When a PD does not send data packets to the switch for a long period in certain
scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD
repeatedly rebooting.
Q4. What should I notice before using the PoE Auto Recovery
feature?
Product specificaties
| Merk: | TP Link |
| Categorie: | Schakelaar |
| Model: | LiteWave LS105GP |
Heb je hulp nodig?
Als je hulp nodig hebt met TP Link LiteWave LS105GP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schakelaar TP Link
2 Mei 2025
10 December 2024
11 November 2024
3 Oktober 2024
31 Juli 2024
10 Juni 2024
7 Mei 2024
7 Mei 2024
7 Mei 2024
7 Mei 2024
Handleiding Schakelaar
- Kraus & Naimer
- Renkforce
- Raritan
- Toolcraft
- 2USB
- INOGENI
- Marmitek
- Silvercrest
- KlikaanKlikuit
- Hama
- Allnet
- QNAP
- Chacon
- Wago
- H-Tronic
Nieuwste handleidingen voor Schakelaar
15 Juni 2025
15 Juni 2025
10 Juni 2025
9 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025