Toa PC-1860 Handleiding

Toa Speaker PC-1860

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa PC-1860 (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

INSTALLATION MANUAL

CEILING MOUNT FIRE DOME SPEAKER

Thank you for purchasing TOA’s Ceiling Mount Fire Dome Speaker.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read

all the instructions in this section for correct and

safe operation.

• Be sure to follow all the precautionary instructions

in this section, which contain important warnings

and/or cautions regarding safety.

• After reading, keep this manual handy for future

reference.

• Use only the specied amplier output voltage

and impedance, as exceeding the specied limits

could result in re or other failures (high-impedance

applications).

• To avoid accidental air explosions, do not use the

unit around gasoline, thinner or other combustibles.

• Install the unit only in a location that can structurally

support the weight of the unit and the mounting

bracket. Doing otherwise may result in the unit

falling down and causing personal injury and/or

property damage.

• Do not use other methods than specied to mount

the unit. Extreme force is applied to the unit and

the unit could fall off, possibly resulting in personal

injuries.

• Tighten each nut and bolt securely. Ensure that

the bracket has no loose joints after installation

to prevent accidents that could result in personal

injury.

• Avoid mounting the unit in locations exposed to

constant vibration. The mounting bracket can be

damaged by excessive vibration, potentially causing

the speaker to fall, which could result in personal

injury.

• To avoid electric shocks, be sure to switch off the

amplier power when connecting the speaker.

• Avoid installing the unit in humid or dusty locations,

or in locations exposed to heaters, solvents, acid,

alkali, smoke, or steam, as excessive exposure to

these factors could result in the speaker falling off,

electric shock or re.

• Do not operate the unit for an extended period of

time with the sound distorting. This is an indication

of a malfunction, which in turn can cause heat to

generate and result in a re.

• Have the unit periodically checked by the shop

from where it was purchased. Failure to do so could

result in the speaker falling off due to damage or

corrosion to the speaker or its mounts, and possible

personal injury.

Indicates a potentially hazardous situation which,

if mishandled, could result in death or serious

personal injury.

WARNING

Indicates a potentially hazardous situation which,

if mishandled, could result in moderate or minor

personal injury, and/or property damage.

CAUTION

PC-1860F, PC-1860BS, PC-1860BS-C

2. GENERAL DESCRIPTION

TOA's PC-1860F, PC-1860BS, and PC-1860BS-C

Ceiling Mount Fire Dome Speakers feature an iron-

made dome that prevents the re from spreading in

the ceiling in case of re.

The speaker can be easily installed using the speaker

mounting spring, and the dome can also be easily

mounted in the speaker mounting hole in the ceiling

panel.

The PC-1860F comes with a push-in type input terminal

block that permits one-touch cable connection as well

as bridging and branch wiring, while the PC-1860BS/

PC-1860BS-C are provided with a steatite terminal

block of screw type.

The PC-1860BS/PC-1860BS-C are certied according

to the European Standard EN 54-24: 2008 and

compliant with the British Standard BS 5839-8: 2008.

Traceability Information for Europe

Manufacturer:

TOA Corporation

7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan

Authorized representative:

TOA Electronics Europe GmbH

Suederstrasse 282, 20537 Hamburg, Germany

Step 5. Press the re dome assembly into the previously prepared hole in the ceiling.

Each leg should settle on the collar.

Push up the dome assembly.

Caution

Since the dome mounting bracket is not placed on the

ceiling panel at this stage, as shown in the above gure,

the dome could fall if released, so continue to provide

manual support.

Dome mounting

bracket

3. INSTALLATION

Step 1.

Using the supplied paper pattern as a guide, open a

156 mm (6.14") ±3 mm (0.12") mounting hole in the

ceiling panel. Ceiling

ø156 ±3 mm

(ø6.14" ± 0.12")

Max. 30 mm (1.18")

Step 2. Punch out the knockout hole in the re dome, then

install the supplied cable entry rubber grommet in

the knockout hole.

Note: The grommet's cable entry hole is covered

with a thin membrane. Cut a hole in the

membrane to match the size of the speaker

cable used.

Fire dome

ø20.5 mm (0.81")

knockout hole

(4 places)

Dome mounting bracket

Step 3. Loosen the wing nut.

Fire dome

Dome mounting

bracket

Important

Unscrew the wing nut until it reaches

the end of the screw shaft.

[Cross-Section View] [Interior View]

Wing nut

Step 6. Push in the dome mounting wing nut.

Firmly push the wing nut and screw shaft

in the direction indicated by the arrow.

The legs of the dome mounting bracket will pop open and

settle on the back surface of the ceiling panel, providing

the dome with partial support. If released, a gap behind

the collar of the dome will result (A).

Wing nut A

Step 4.

Feed the speaker cable through the rubber grommet into the dome interior.

Step 7.

Turn the dome mounting wing nut clockwise to tighten and rmly secure the dome to the ceiling panel.

Wing nut Tighten fully for a secure installation.

Fire dome mounted

to the ceiling

Terminal block

• PC-1860F:

• PC-1860BS:

• PC-1860BS-C:

Push-in type input terminal

Steatite terminal

Speaker mounting

spring

Speaker mounting

spring

Speaker cable

[PC-1860F terminal block]

When making a bridge connection:

Push-in type

input terminal

From

the amplifier To

the next speaker

COM

6 W (1.7 kΩ)

9 mm

(0.35")

[PC-1860BS/1860BS-C terminal block]

When making a bridge connection:

From

Amplifier To

the next speaker

COM

Earth

5 mm

HOT

Steatite terminal

COM

Earth

HOT

The gure shows

PC-1860BS.

Wiring diagram

8 Ω

* Factory-preset

COM

(white)

COM

(–)

HOT

(black)

HOT

(+)

Input connector

13 kΩ

6.7 kΩ

3.3 kΩ

1.7 kΩ*

COM

Matching

transformer

Input connector

Matching

transformer

Input connector

Matching

transformer

8 Ω

13 kΩ

6.7 kΩ

3.3 kΩ

1.7 kΩ*

COM

Earth

HOT

COM

Earth

HOT

COM

Thermal fuse

(72 ºC or 161.6 ºF)

8 Ω

13 kΩ

6.7 kΩ

3.3 kΩ

1.7 kΩ*

COM

Earth

HOT

COM

Earth

HOT

COM

Thermal fuse

(72 ºC or 161.6 ºF)

* Factory-preset

• PC-1860BS-C

• PC-1860BS

• PC-1860F

1 µF 250 V

Step 8. Make wiring.

8-1. Insert the lead-in cables (cables from the amplifier)

and lead-out cables (cables to other speakers) into the

input connector according to the terminal indication.

Note: Hook the two ends of one of the speaker

mounting springs into the hooks in the re

dome during connection.

Product specificaties

Merk:	Toa
Categorie:	Speaker
Model:	PC-1860
Kleur van het product:	Black,White
Gewicht:	560 g
Breedte:	180 mm
Diepte:	180 mm
Hoogte:	70 mm
Materiaal behuizing:	Staal
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	6 W
Aantal per verpakking:	1 stuk(s)
Aanbevolen gebruik:	Intercomsysteem
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Diameter driver:	120 mm
Frequentiebereik:	80 - 20000 Hz
Gevoeligheid:	94 dB
Versterker:	Nee