The Galley Tap Handleiding
The Galley
Kraan
Tap
Bekijk gratis de handleiding van The Galley Tap (8 pagina’s), behorend tot de categorie Kraan. Deze gids werd als nuttig beoordeeld door 11 mensen en kreeg gemiddeld 4.6 sterren uit 6 reviews. Heb je een vraag over The Galley Tap of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Galley Tap Installation Guide
THEGALLEY
®
TAP
1
1
Before You Begin Installation
Package Contents
Tools
1. Observe all local plumbing codes.
2. Turn off water supply.
3. Inspect water supplies for signs of damage. Replace if necessary.
4. DO NOT use petroleum-based products on this faucet.
INSTALLATION WARNING: NEVER USE TEFLON TAPE FOR OUT-OF-THE-WALL THREADED CONNECTIONS. USE
PROVIDED CONTENTS ONLY. NOT COMPLYING WITH THIS INSTRUCTION COULD DAMAGE THE PRODUCT AND
GENERATE LEAKAGE.
#2 & #3 PHILLIPS SCREWDRIVERS ADJUSTABLE WRENCH ADJUSTABLE PLIERS
Remove all contents from the package and
identify before installation.
1 - Aerator Key
2 - Galley Tap
3 - Optional Base Ring
4 - Mounting Washer
5 - Mounting Nut with Two Crosshead Screws
6 - Counterweight with two rubber strips
Note: All Hoses come pre-installed into Tap and are
water tested at the factory.
Recommended Pressure Range: 20PSI -
75PSI
Maximum Flow Rate: l.8GPM / 6.8L /min
Maximum Temperature: 150° F
Product is Certified to NSF/ ANSI 372 and conforms with
the lead content requirements for “lead free” plumbing as
e defined by California, Vermont, Maryland, and Louisiana
state laws and the U.S. Safe Drinking Water Act. This
faucet complies with ASME 112.18.1-2018/CSA B125.1-2018
requirements.
2
1
3
5
6
4
TECHNICAL INFORMATION
2
Optional Base Ring
Washer
Mounting Nut
Crosshead Screws
Ø 1- 1/2” fast water jet hole in
counter top
Ø 1-3/8” drill hole in counter top
Mounting Shank
Installation
Step 1
Step 2
Step 3
Hand Spray Supply Hose
Hand Spray Hose
Cold Supply
Hot Supply
Check Valve Housing
VERY IMPORTANT!
Step 5
Step 4
Step 6
Note: make sure the Hand Spray Hose
and Counterweight are free to extend
or retract and are not in conflict with
any plumbing components or items
under the Workstation.
H
C
1”
The Galley Tap comes with an
Optional Base Ring. It can be
installed with the Base Ring or
without it.
Insert all hoses and Mounting
Shank through the hole in counter
top.
On the underside of the counter
top, install the Washer and
Mounting Nut by slipping them
over the hoses and threading the
nut onto the Mounting Shank.
Tighten the Mounting Nut against
the counter top and tighten the
two screws so the Tap is secure.
Install the Counterweight onto the
Hand Spray Hose as shown.
Proper placement of the
Counterweights is critical for the
proper retraction of the spray hose.
Hand Spray Hose
Connect the Hand Spray Hose to the
Hand Spray Supply Hose in which
the Check Valve housing is fitted.
Before connecting the hot and cold
Supply Hoses, flush water supply
stops to clear any debris. Place a
bucket underneath the hoses and
carefully turn on the water. Run
water for 5 to 10 seconds.
Carefully position hot and cold
supplies so they will not interfere
with other hoses.
Connect the 3/8” Compression
Connections (Hot and Cold Supply
Hoses) to your hot and cold inlets.
Hoses are marked hot and cold.
Product specificaties
| Merk: | The Galley |
| Categorie: | Kraan |
| Model: | Tap |
Heb je hulp nodig?
Als je hulp nodig hebt met The Galley Tap stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kraan The Galley
17 Juni 2025
16 Juni 2025
16 Juni 2025
11 September 2023
Handleiding Kraan
- Teka
- Aloni
- Empire
- Hansgrohe
- InSinkErator
- Omnires
- IKEA
- Gessi
- Elba
- ProFlo
- Sani-Lav
- Elkay
- Axor
- Rohl
- Graff
Nieuwste handleidingen voor Kraan
23 Mei 2025
21 Mei 2025
20 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025
2 Mei 2025
25 April 2025