Tennsco 1842 Handleiding
Lees hieronder de đ handleiding in het Nederlandse voor Tennsco 1842 (4 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing a
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modiîcation or repair by person
shipment, or where the date stamps on the goods have been defaced, modiîed or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Sellerâs premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-2570918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Deluxe Storage Cabinet
Unassembled Models 1842 & 2442
Tennsco LLC., Dickson, TN 37056-1888 ⢠(866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
36w x 24d
200 lbs.
200 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1842 OR 2442 CABINET
Tools Needed: A free 11/ â nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the cabinet back (Ref. No. 1) on a protected surface
to prevent scratching the paint. The îange on the bottom of
the back should be facing upward.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
îange (A) around the back and bolting the back and side
together with four bolts and nuts (Ref. Nos. 15 & 16). Be
sure that the lances on all shelf adjustment strips (B) point in
the same direction.
5. Insert one shelf (Ref. No. 4) into the approximate center
of the unit, inserting the shelf edges into the lances on all
four shelf adjustment strips. Be sure that the channeled
edge of the shelf is toward the cabinet front.
6. Place the second shelf at the desired level in the
same manner as in step 5. Next, attach the door frame
assembly (Ref. No. 6) to the cabinet body by placing
it over the sides. Align the weld studs with the slots in the
left and right sides, and attach using four nuts on each side.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as in step 3, again making sure that the îange
is around the back and that
the lances on the shelf
adjustment strips
are pointed in
the same
direction as
those on the
back and
left side.
All lances point UP on
the back and side.
B
Flange faces upward.
Flange goes
under back.
A
Channeled edge of the shelf is
toward the front of the unit.
1. Place the locking handle
(Ref. No. 9) on the right
hand door and fasten with
two #8-32 X 1/4 hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 10) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
12) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 8) to the locking cam (see
âAâ at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
11) over the lock bar
ends and through the
door slots (see âBâ at
right). Push down îrmly
until the guides snap
into place.
5. Attach the âdummyâ handle
(Ref. No. 13) using two
#8-32 X 1/4 hex-head bolts
and lock washers.
Handle/Locking System Installation
A
B
B
7. Set the unit upright and attach the top (Ref. No. 5) by inserting
the weld-studs into the holes provided on the left and right
sides. The îange should ît over the outside of the rear of the
cabinet, and theoffset should be toward the front. Bolt
together by attaching nuts to the weld studs and inserting
bolts and nuts through the holes along the back edge.
8. Open the doors and place the bottom (Ref. No. 4) in the
lowest notch of the shelf adjusting strips on the sides and
back. The îange with the two holes nust face the front,
and ît over the base plate of the frame. Shelves may now
be adjusted as desired.
9. Cabinet must be level for doors to
open and close properly. Insert a
îathead screwdriver into the two
leveling holes and turn the screws
until the cabinet is level.
Product specificaties
| Merk: | Tennsco |
| Categorie: | Kast |
| Model: | 1842 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tennsco 1842 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kast Tennsco
20 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
6 Juni 2023
6 Juni 2023
4 Juni 2023
30 Mei 2023
26 Mei 2023
23 Mei 2023
Handleiding Kast
- Kast HP
- Kast IKEA
- Kast Siemens
- Kast Apc
- Kast Bopita
- Kast Bruynzeel
- Kast Butler
- Kast Flexa
- Kast Foppapedretti
- Kast Gude
- Kast Handson
- Kast Livarno
- Kast Marantz
- Kast Milwaukee
- Kast Miomare
- Kast Powerfix
- Kast Sencys
- Kast Tiger
- Kast United Office
- Kast Wehkamp
- Kast Woood
- Kast Jysk
- Kast Leen Bakker
- Kast Parisot
- Kast Talgø
- Kast Tvilum
- Kast Bush
- Kast Silver Cross
- Kast Vipack
- Kast BoConcept
- Kast KidKraft
- Kast MADE
- Kast Nolte
- Kast Rauch
- Kast BDI
- Kast Zuiver
- Kast Profijt Meubel
- Kast Ordex
- Kast Hygena
- Kast Kwantum
- Kast Kirkton House
- Kast Empire
- Kast Dutchbone
- Kast Hooker
- Kast Calligaris .com
- Kast Gami
- Kast Livarno Lux
- Kast Toomax
- Kast Gladiator
- Kast Arthur Berndt
- Kast Bbf
Nieuwste handleidingen voor Kast
2 Mei 2024
30 April 2024
28 April 2024
28 April 2024
28 April 2024
20 April 2024
20 April 2024
20 April 2024
20 April 2024
16 April 2024