Tenderfoot Electronics SVF-1 Handleiding
Bekijk gratis de handleiding van Tenderfoot Electronics SVF-1 (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 25 mensen en kreeg gemiddeld 5.0 sterren uit 13 reviews. Heb je een vraag over Tenderfoot Electronics SVF-1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
SVF-1 Manual
SVF-1
State Variable Filter
Manual revision 1/11/2020
1
SVF-1 Manual
Table of Contents
Page 3
● Overview
● Installation
◦Connecting power to the module
Page 4
● Panel Layout
Page 5
● V/Oct Calibration
Page 6
● Important things to note and remember
● Contact Us
2
SVF-1 Manual
Overview
SVF-1 is a state variable filter with voltage controlled cutoff and resonance. The SVF-1
self-oscillates when the resonance is turned up and has a 1V/octave input for use as a
sine wave VCO. The resonance circuit includes a Q control, a drive control, and a
more/less polite to crank up the resonance even more. The Q control is also controllable
via a CV input jack. All outputs are available simultaneously in Low Pass, Band Pass, High
Pass, and Notch mode.
Installation
Tenderfoot Electronics modules are designed to be used with a Eurorack-compatible case
and power supply. Before installing a new module into your case, please ensure that your
power supply and case have sufficient space and available capacity to power the module.
The SVF-1 draws current from the +12V and -12V rails, and can be used in cases without
a 5V rail.
Failure to adequately power your modules may result in damage to your modules or power
supply. If you are unsure, please contact us before proceeding.
Before installing or removing a module from your rack, ensure that you turn off the power
supply for the case. If a module is removed or installed while the rack power supply is
switched on, it could cause serious damage to either the module, or power supply, or both.
Connecting the power cable to the module:
The power header is labelled at one end with a bold stripe,
and the words “red stripe -12V”. Align the red stripe on the
ribbon cable with the “red stripe” label on the PCB.
Once the cable is attached to the module, connect the
16-pin end of the cable to your case's power supply, again
ensuring the red stripe lines up with that of the power
supply PCB.
Using the included screws, screw the module on to your
rails, power up, and enjoy! If at any time you notice
irregularities in the operation of the module, turn off the
case and inspect all connections and cables.
3
Product specificaties
| Merk: | Tenderfoot Electronics |
| Categorie: | Niet gecategoriseerd |
| Model: | SVF-1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tenderfoot Electronics SVF-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Tenderfoot Electronics
14 Augustus 2023
14 Augustus 2023
14 Augustus 2023
Handleiding Niet gecategoriseerd
- Mauser
- WyreStorm
- Z.Vex
- Coca-Cola
- Mammut
- Rinnai
- Beaphar
- Argoclima
- Noveen
- Ardes
- Ridem
- Weber
- Rossi
- Sogo
- Koala
Nieuwste handleidingen voor Niet gecategoriseerd
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025