Techly I-WL-CPE880 Handleiding

Techly Access point I-WL-CPE880

Bekijk gratis de handleiding van Techly I-WL-CPE880 (48 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.4 sterren uit 2 reviews. Heb je een vraag over Techly I-WL-CPE880 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PDF downloaden

Pagina 1/48

WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM WWW.TECHLY.COM

EN User’s Manual

Place the CPE to the

selected position and

adjust the CPE front

panel orientation to be

approximately the same

as the selected direction.

Connect the PoE adapter’s

LAN to PC, Router or Switch

based on the network

topology.

Please prepare a long

enough network cable to

connect the POE adapter

and CPE. Recommend to

use a Category 5E (or

above) shielded network

cable with a ground wire.

Completed connection, push up to restore the

CPE back cover.

Point to multiple pointPoint to Point

In the wireless monitoring

transmission, it is recommended to

use the above graphic method for

point-to-point or point-to-multi-

point transmission.

The wireless bridge/outdoor CPE

transmission angle is oriented at

60 degrees. Please adjust the

equipment’s angle when building

point-to-multi-point transmission.

Check the local network connection

Set Static IP address for PC

P/N: I-WL-CPE80

8051128108453

P/N: I-WL-CPE120

8051128108446

P/N: I-WL-CPE880

8051128108439

POINT-TO-POINT CPE

S M

IP Camera

IP CameraIP Camera

IP Camera

Repeater

Repeater Repeater

Monitoring

DVR

Switch DVR

Wireless Network

Disable

Connect/Diconnect

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Device installation

Passive PoE Adapter supports up to 60 meters (200 feet) Power over Ethernet

deployment

Wireless Connection TopologyLED Display CPE

1. Default working mode is Slave CPE or Client, IP: 192.168.2.1.

2. Set one CPE to Master CPE or Host, in LED Display will start with “H”:

Nota: F is function and confirm button;

S is setting button.

F (Press F button to choose the function need to set) - S (Press

S button to set the value like operation mode, channel) - F

(Press F button again to confirm the value, success after

blinking 5 seconds)

H--- Master CPE

060---channel 60

C--- Slave CPE

060--- channel 60

3. Master CPE channel must be same as Slave CPE:

4. Press Reset 1 second on both side, the two outdoor devices will start bridging:

(Nota: LED Display CPE will be finished in 2 minutes 20 seconds.)

Finish within 2’20’’

Press Reset on both side

at same time

Slave CPEMaster CPE

WEB Configuration

1. PC configuration if PC connect CPE by wireless

Set PC wireless network IP to 192.168.2.x (x: 2--250), same network segment as CPE, subnet mask:

255.255.255.0:

2. PC configuration if PC connect CPE wired

If connect PC and CPE wired, Set PC local network IP to 192.168.2.x (x: 2--250), same network segment

as CPE, subnet mask: 255.255.255.0:

Local Network Properties

Networking Sharing

Connect using:

InstalllUninstalll Propertie

Decription

Transmission Control Protocol/Internet Protocol.The default

widearea network protocol that provides communication

across diverse interconnected networks.

This connection uses the following items:

Client for Microsoft Networks

QoS Packet Scheduler

File and Printer Sharing for Microsoft Networks

Internet Protocol Version6(TCP/IPv6)

Internet Protocol Version4(TCP/IPv4)

Link-Layer Topology Discovery Mapper I/O Driver

Link-Layer Topology Discovery Responder

Realtek PCle GBE Family Controller

Configure...

OK CancelOK

Advanced...

Cancel

Internet Protocol Version 4(TCP/IPv4) Properties

General

IP address:

Subnet mask:

Default gateway:

Use the following DNS server addresses:

Preferred DNS server:

Alternate DNS server:

Obtain an IP address automatically

You can get IP settings assigned automatically if your network supports

this capability.Otherwise,you need to ask your network administrator for

the appropriate IP settings.

Validate settings upon exit

192.168.2.x

255.255.255.0

. . .

Use the following IP address:

Obtain DNS server address automatically

After IP address configuration, connect to CPE’s wireless SSID: TECHLY5G

Local Network

yunlink 8

Realtek PCIe GBE Fam