Tascam TT-M1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Tascam TT-M1 (28 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
»
TT-M1
Scratch Control Unit
D00811500A
OWNER'S MANUAL / MODE D'EMPLOI / BEDIENUNGSANLEITUNG /
MANUALE D'ISTRUZIONI / MANUAL DEL USUARIO / 取扱説明書
English . . . . . . . . . . . . . . . . . . . . . . . . . 2
Français . . . . . . . . . . . . . . . . . . . . . . . . 6
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . 10
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . 14
Español . . . . . . . . . . . . . . . . . . . . . . . . 18
日本語 . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2English
Read this manual thoroughly before using the
product, and keep it handy for future reference.
The TT-M1 is a special controller for the TAS-
CAM CD-X series of CD players (hereafter
referred to as CD-X). When a record player
equipped with the TT-M1 is being used to con-
duct scratching, the controller detects the
turntable's rotating direction and speed and trans-
fers them to the CD-X. The CD-X then plays
back the scratching on a CD with great accuracy.
The names of the companies and products that
appear in this document are the trademarks or
registered trademarks of their respective hold-
ers.
Do not connect the product to any equipment
other than the CD-X.
This product is powered by the CD-X unit.
When the product is not in use, always turn off
the POWER switch and raise the roller to an
upright position.
Introduction
Installation
The TT-M1 can be attached to the following
record players using accessory adapters. Install
the adapter in the specified position on the base
unit and then affix the product to the record play-
er.
Mounting
Model hole Adapter
Technics SL-1200MK2 T2 T2
Technics SL-1200MK3 T3 V
Numark TTX1 N N
Vestax PDX-2000 V, T2 V, T2
If you want to install the TT-M1 on models other
than these, fix it in place with double-sided tape
or by other means.
Technics SL-1200MK2
Attach adapter T2 to mounting hole T2 and insert
the TT-M1 into the dust cover holder.
Technics SL-1200MK3
Attach adapter V to mounting hole T3 on the
back of the base unit, and insert the TT-M1 into
the headshell stand.
Numark TTX1
Attach adapter N to mounting hole N on the back
of the base unit, and insert the TT-M1 into the
headshell stand.
3English
2 Loosen the mounting screw.
3 Adjust the height so that the roller is posi-
tioned horizontally on the turntable.
Align these lines with each other.
4 Move the product to the left and right in
order to align the axis of the roller with the
center of the turntable. Use the guides at the
base of the roller.
Guide
Guide
5 When the product is properly adjusted, tight-
en the mounting screw securely.
Adjust the vertical and horizontal positions of the
TT-M1 as follows. Note that a record does not
have to be placed on the turntable.
1 Lower the roller onto the turntable.
Roller
Mounting
screw
Adjustment
Vestax PDX-2000
Attach adapter V to mounting hole V on the back
of the base unit, and adapter T2 to mounting hole
T2 on the top surface. Install the TT-M1 by
inserting adapter V into the headshell stand and
placing adapter T2 on the dust cover holder.


Product specificaties

Merk: Tascam
Categorie: Niet gecategoriseerd
Model: TT-M1

Heb je hulp nodig?

Als je hulp nodig hebt met Tascam TT-M1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Tascam

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd