Tascam IF-AV/DM Handleiding

Tascam Niet gecategoriseerd IF-AV/DM

Lees hieronder de 📖 handleiding in het Nederlandse voor Tascam IF-AV/DM (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 128 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

IF-AV/DM

Aviom Pro16 A-Net Interface Card

D01106120A

Introduction

Thank you for purchasing the TASCAM IF-AV/DM

Aviom Pro16 A-Net Interface Card. This card allows your

TASCAM Digital Mixer to feed monitor audio to any

number of Aviom Pro16 A-Net devices such as the A-16II

Personal Mixer.

Before using the unit, please take time to read this manual

thoroughly to ensure you understand how to properly set up

and connect the unit, as well as the operation of its many

useful and convenient functions. After you have nished

reading this manual, please keep it in a safe place for future

reference.

You can also download the Owner’s Manual from the

TASCAM web site (http://www.tascam.com).

Features

Transmission of up to 16 channels of audio.

•

Compatible with 24 bit quantization and 44.1 kHz and 48

•

kHz sampling frequency

Convenient on-screen stereo link control.

•

Trademarks

TASCAM is a trademark of TEAC Corporation,

•

registered in the U.S. and other countries.

Aviom, A-Net, and Pro16 are trademarks of Aviom, Inc.

•

Other company names, product names and logos in this

•

document are the trademarks or registered trademarks of

their respective owners.

Product components

The included items are listed below.

Take care when opening the package not to damage the

items. Keep the package materials for transportation in the

future.

Please contact the store where you purchased this unit if any

of these items are missing or have been damaged during

transportation.

Main unit

• .........................................................................1

Attachment screws

• ..........................................................5

Owner’s Manual (this document)

• ....................................1

Names and functions of parts

1RJ-45 Connector for A-Net

DM-3200/DM-4800 requirements

In order to use the IF-AV/DM card, the DM-4800/DM-3200

must use software version 1.70 or later. The mixer cannot

recognize the IF-AV/DM card when using earlier versions.

Check the TASCAM website (http://www.tascam.com/) for

the latest DM-4800/DM-3200 software and download the

TFI update le.

Install TMCompanion, which is included on the CD-ROM

included with the DM-4800/DM-3200, on the computer

that you are using. Launch TMCompanion and use the TFI

update le to upgrade the software version used by the

DM-4800/DM-3200.

Installation

NOTE

DM-3200: Install the IF-AV/DM in mixer slot 1. It will not •

function in slot 2.

DM-4800: Install the IF-AV/DM in mixer slot 1 or 3. It will •

not function in slot 2 or 4.

Turn the mixer power OFF before beginning installation. •

1 Remove the five screws from the cover panel of the

slot where you want to install the IF-AV/DM card

(slot 1 on a DM-3200, slot 1 or 3 on a DM-4800), and

then remove the panel. (If that slot already contains

a card, remove the card.)

2 Insert the IF-AV/DM card into the slot. Insert the

card completely, aligning its edges with the white

guidelines on the inside of the slot. Push the card

in until it clicks into place and its backplate is even

with the back of the mixer. Do not, however, push the

card too hard. If you are having difficulty inserting it

properly, pull it out once and try again.

3 Use the five screws that you removed earlier or the

five screws included with this card to fix the card in

place.

4 Turn the mixer’s power ON, and open the DIGITAL

screen (with the ALT key indicator lit, press screen

mode selection key 2). Select the SLOT tab (SLOT

1-2 or SLOT 3-4 for the DM-4800), and confirm that

the unit recognizes the installed card. If a “No Card”

message appears, the card might not have been

inserted properly or the screws might not be tight

enough.

Compatibility

The IF-AV/DM interface card, when installed and properly

congured, is compatible with the following Aviom Pro16

Series products:

A-16II Personal Mixer (the original A-16 is not

•

supported)

A-16R rack-mounted Personal Mixer

•

AN-16/o Output Module

•

2 TASCAM IF-AV/DM

IF-AV/DM

Aviom Pro16 A-Net Interface Card

A-16D Pro A-Net Distributor

•

AV-P2 Output Module

•

Connecting Pro16 devices

With the IF-AV/DM card properly installed and congured,

you can now connect Pro16 monitoring and audio

networking devices. Connecting a Cat-5e cable from the

A-Net output of the IF-AV/DM card to the A-Net In on the

rst Pro16 devices starts an A-Net distribution network. No

conguration is required for the Aviom devices.

Pro16 A-Net allows both serial (daisy chain) and parallel

connection topologies. Cat-5e cable connections can be up

to 500 feet (150 meters) between each Pro16 device. Simply

connect A-Net Out to A-Net In on each device. Parallel

connections can be made using A-Net distribution hubs

(such as the A-16D or A-16D Pro). There is no limit on the

number of A-Net Distributors or A-Net audio devices that

can be used in a system.

CAUTION

Do not use shielded Cat-5e cables with A-Net devices. Be

sure to use only standard Cat-5e cables, not those sold as

crossover cables. A crossover cable is not compatible with

the IF-AV/DM or Aviom equipment.

Series connections

The diagram above shows an IF-AV/DM card installed

connected in series to a group of A-16II Personal Mixers.

Any number of A-Net devices can be connected in this

manner. Cables runs can be up to 500 feet, 150 meters long

between devices. Each A-16II Personal Mixer should be

individually powered.

Parallel connections

Parallel connections avoid some of the pitfalls of a

serially-connected system. Each A-Net device is directly

connected to a data source instead of depending upon the

previous user in a daisy chain for data delivery.

The preceding diagram shows an IF-AV/DM card connected

to an 8-port A-Net distributor. The A-16D Pro distributor

shown allows up to eight simultaneous parallel A-Net

connections. With this arrangement, power is also supplied

to each A-16II personal mixer over the CAT-5e cable.

About Pro16 A-Net

A-Net is Aviom’s proprietary high-speed data transmission

protocol designed specically to transport uncompressed

high delity streaming audio in real time over inexpensive

Cat-5e cabling.

A-Net as implemented in Pro16 products transports sixteen

channels of digital audio (44.1kHz or 48kHz, 24-bit) from

the IF-AV/DM card to each Personal Mixer or AN-16/o

Output Module connected to the system. An unlimited

number of Pro16 A-Net devices can be connected to a

system. A-Net’s proprietary design delivers ultra-low

latency (less than 1 msec from analog input to analog

output) in all congurations.

CAUTION

A-Net is based on the physical layer of Ethernet, which

provides Pro16 A-Net a mature and robust base on which

to build. However, Aviom products are not compatible

with off-the-shelf computer products designed for

Ethernet networks such as hubs, routers, and switches.

Cable lengths

Your cable length performance will be affected by a number

of factors including the quality of the cables used, and the

number of devices such as cable couplers used or wall panel

interconnections in use.

To go longer than the maximum specied distance A-Net

allows (500 feet, 150 meters), an A-Net Distributor product

can be used as a signal repeater. Simply insert the A-16D or

A-16D Pro into the A-Net stream at the 500-foot point and

the A-Net signal will be refreshed.

Another 500 feet (150 meters) of cable can then be added.

This process can be repeated as many times as required to

extend cables.

In fact, any Pro16 A-Net device that has an A-Net out

connector can be used as a signal repeater.

IF-AV/DM

Aviom Pro16 A-Net Interface Card

TASCAM IF-AV/DM 3

NOTE

Using the A-Net out connector of, e.g. a A-16II Personal

Mixer to extend the signal does not supply power to the

additional units, which must be powered individually.

For long distance applications, ber optic cable can be

used to span distances up to 50 miles (80 km) with the

use of devices called media converters. A media converter

changes the Ethernet-based Pro16 A-Net signal to ber

optic at the source location and then back to Cat-5 at the

destination. Several companies make fast Ethernet to ber

media converters that can be used with your IF-AV/DM and

Aviom equipment.

Mixer control screen

On both the DM-3200 and DM-4800, the IF-AV/DM

presents a setup display screen as shown below.

Navigate to the Digital page (LCD access button 2 with

blue LED lit), and then select the ALT SLOT tab (labeled

SLOT 1-2 or SLOT 3-4 on the DM-4800)

Use the 4 arrow keys to the right of the LCD screen to move

the cursor over to the A-Net Card area. It may be on the left

or the right hand side of the screen, depending on which

slot the card is inserted into. Use the key to make ENTER

changes.

The dial can also be used to move the cursor up JOG/DATA

and down.

This display has the following:

STATUS

This shows whether the IF-AV/DM card itself is working

correctly and the state of the A-Net.

CARD Status

• :

The IF-AV/DM is running at full 16 channel count.

Unsupported FS

• :

The mixer is not running at 44.1 kHz or 48 kHz, so the

IF-AV/DM will not pass audio.

Not Responding

• :

A problem was encountered during configuration.

A-Net Status

• :

The IF-AV/DM is connected to one or more A-Net

receivers.

xxx

• Timeouts:

A problem was encountered.

STEREO LINK

Use the up and down arrows and then the button to ENTER

toggle the state of the channel pairs that you wish to link

or unlink. When linked, the display on the Personal Mixers

will change to show a stereo spread control instead of a

pan control for those two channels. The channel’s volume

will also be controlled as a pair. Compatible A-Net devices

that do not respond to stereo linking will not be affected by

changes to the Stereo Link status.

System clocking

Master clock

When congured with an IF-AV/DM, the mixer can have

any clock source as long as it is 44.1 kHz or 48 kHz. The

IF-AV/DM does not operate at the 2x rates of 88.2 kHz and

96 kHz, so when the mixer is running at these rates, the

A-Net output from the IF-AV/DM will be silent, and the

LCD screen will show “Unsupported FS ” for the A-Net

Status eld.

Varispeed pitch

The DM-3200 and DM-4800 can run at non-standard

Sample Rates when locked to an external clock.

The IF-AV/DM will follow along up to the limits of the

mixer’s clock.

Here are the supported pitch ranges.

44.1 kHz : -6.0% to +6.0%

•

48 kHz: -6.0% to +6.0%

•

Outside of these ranges, the mixer will mute and report a

clock error.

DM-3200/4800 settings

The IF-AV/DM appears to the Mixer just like any other

optional I/O card except that it may have 16 channels of I/O

instead of 8 depending on whether the card is inserted into

slot 1 (or slot 3 for the DM-4800).

Mixer outputs

By default, the DM-3200/DM-4800 routes busses 1 – 16 to

IF-AV/DM outputs 1-16.

These routing settings can be changed in the OUTPUT SLOT

tab of the DM-3200/DM-4800’s ROUTING screen.

Product specificaties

Merk:	Tascam
Categorie:	Niet gecategoriseerd
Model:	IF-AV/DM

Heb je hulp nodig?

Als je hulp nodig hebt met Tascam IF-AV/DM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Tascam

Tascam DR-10L Pro Handleiding

4 Augustus 2023

Tascam TC-8 Handleiding

13 Juni 2023

Tascam US-800 Handleiding

12 Juni 2023

Tascam 424MKIII Handleiding

23 Mei 2023

Tascam DP-008 Handleiding

13 Mei 2023

Tascam VL-A4 Handleiding

11 Mei 2023

Tascam US-1200 Handleiding

25 April 2023

Tascam MiNiSTUDIO Creator US-42B Handleiding

23 April 2023

Tascam TT-M1 Handleiding

23 April 2023

Tascam Podcast Editor Handleiding

21 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024