Synco P1L Handleiding

Bekijk gratis de handleiding van Synco P1L (2 pagina’s), behorend tot de categorie Microfoon. Deze gids werd als nuttig beoordeeld door 26 mensen en kreeg gemiddeld 4.5 sterren uit 5 reviews. Heb je een vraag over Synco P1L of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Thank you for choosing SYNCO product.

Please read this manual carefully before use and follow all instructions

mentioned herein.

Microphone P1L User Manual

Caring For Your SYNCO Product

Package List

Product InstructionOperations

Please keep the product in a dry, clean, dust-free environment.

Keep corrosive chemicals, liquids and heat source away from the product

to prevent mechanics damage.

Use only a soft and dry cloth for cleaning the product.

Malfunction may be caused by dropping, impact of external force.

Do not attempt to disassemble the product. Doing so voids warranty.

Please have the product checked or repaired by authorized technicians if

any malfunctions happened.

Failure to follow all the instructions may result in mechanics damage.

Warranty does not apply to human errors.

TX Transmitter x1RX Receiver (Lightning

Connector) x1Wireless Charging

Case x1

Charging Cable x1Type-C to 3.5mm Adapter x1

TX Transmitter

RX Receiver

Wireless Charging Case

Indicator — Receiver

Indicator — Wireless Charging Case

Indicator — Transmitter (Double press the Power button to turn o󽗈 light

e󽗈ect)

① Power

② Working Indicators

③ Built-in Mic

④ Contacts

⑤ Pocket Clip

① Vocal E󽗈ects

② Type-C Port

③ Working Indicators

④ Connector

⑤ Contacts

① Pairing/ Power Prompt

② Type-C Port

③ Working Indicators

④ Contacts

1. Usage

2. Manual Pairing

3. Charging

4. Check the power

5. Use vocal e󽗈ects

① Tap on the right side of charging case to pop

out the drawer

② Take the TX and RX out

③ TX should boot automatically as it leaved the

case, and switch itself o󽗈 automatically when

returning to the case.

① Place the TX and RX in the case with their

contacts are connected with the case’s

② Long press the Pairing button on the case for

3 seconds with the drawer open

③ The indicators on the TX and RX should light

up and illuminate sequentially when pairing is

successful

Note: The transmitter will automatically switch

o󽗈 if it is unpaired or disconnected for 5 minutes.

Charge the TX: Place the TX in the case with

contacts connected with the case’s.

Charge the case: Connect the case with power

supply via the charging cable.

TX: Short press the Power button, the indicators will light up according to

remain power for 5 seconds

Charging Case: Short press the Power Prompt button, the indicators will

light up according to remain power for 5 seconds

Short press the Vocal E󽗈ects button on the receiver to switch sound e󽗈ects:

Original >> Studio FX >> KTV FX >> Voice Ampli󽗉cation >> EDM (Electronic

Dance Music) >> Baby FX >> Male to Female >> Female to Male >> Monster FX.

Default e󽗈ect: Original

Flash concurrently

Flash concurrently

Illuminate sequentially

Single light keeps on &

Illuminate sequentially

Single light keeps on (In the

case)

Illuminate sequentially (Light

e󽗈ect on)

Single light keeps on (Light

e󽗈ect o󽗈)

Single light 󽗊ashes

Illuminate sequentially

Single light 󽗊ashes twice &

Illuminate sequentially

System unpaired

System unpaired

Pairing

Original sound

Charging, and then turns o󽗈 when fully

charge

System paired, normal working

System paired, normal working

Low battery

System paired

Vocal e󽗈ects on

Working Indicators (White Light)

Working Indicators (White Light)

Working Indicators (White Light)

Working Indicators (Red Light)

Long press for 3 seconds

(Forcible switch: Long press the Power button on TX for 3 seconds)

④ RX should boot automatically as it is plugged into smartphone

Product specificaties