Swan SI9050 Handleiding

Swan Stoomgenerator SI9050

Lees hieronder de 📖 handleiding in het Nederlandse voor Swan SI9050 (1 pagina's) in de categorie Stoomgenerator. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

1. Fill water tank with clean water as above filling instruction. For better performance,

please immerse the filter in water for several minutes before installing it into the water

tank. If you live in a hard water area used bottled water.

2. Connect the appliance into a suitable socket outlet. Lay down handle and press down

the power switch on the control panel. Water tank decorative indicator light lights up to

indicate that the unit has been connected to the power supply.

3. Set temperature control knob to steam ironing position according to fabric setting

chart mentioned above. Heating indicator light at iron unit lights up to indicate the unit is

being heated up. When the heating indicator light turns off, the desired temperature

has been reached. It is ready for steam ironing. During use, heating indicator light cycle

from on to off, (For every first time use, please pre-heat for 3 minutes)

4. Before every first time use, it is proposed to clean iron unit as following methods: Take

the iron up from the base unit, press steam release button underneath the handle to

allow steam ON for 30 seconds, and then OFF for 30 seconds, this cycle should be

repeated for 2 times. When heat indicator light turns off, it is ready for use.

5. During steam ironing, please adjust steam rate according to your requirement as

indicated in the steam selection.

6. After use, put iron unit back on the base unit again, turn temperature control knob

to“MIN”, and then unplug the appliance from main socket .

7. Take out filter and pour out the remaining water.

Note:

a. For every first time use, it is normal that a slight vibration sound may be heard from

electrical pump inside the base unit for a few seconds when steam ironing started. It is

because there is air inside the filter, it will stop when the air inside the filter has been

pumped out. Press and HOLD the trigger for up to 30 seconds. If necessary hold the

iron hand unit below the base. This clears any air locks more quickly

b. When the temperature control knob is set at “ (SYNTHETIC)” position, no steam is

produced as it only suits dry ironing. When set at “ (WOOL/SILK)” or

“ (COTTON)” , “MAX” , steam will automatically vary according to soleplate

temperature.

5 6 7 8 9 10 11 12

Parts and Features Fabric Setting Chart Ironing Temperature Setting Guide How to use your steam station How to use your steam station

1. Water tank

2. Handle

3. Filter

4. Soleplate

5. Heating indicator light

6. Steam release button

7. Temperature control knob

8. Power cord/Supply hose

9. Power cord

10. Unlock button

11. Iron rest

12. Pump working indicator light

13. Steam control knob

14. Power switch

12 13

Temperature control knob

Temperature

Setting

Fabric

SYNTHETIC WOOL/SILK COTTON MAX

Synthetics, Silk,

Nylon, Arcrylic,

Acetate

Wool, Silk

Polyester

Cotton

Linen

Cotton

Linen

Ironing

Instruction

Dry Ironing Dry iron on the

wrong side of

the

fabric.

Steam Ironing Steam Ironing

Steam Selection

Low Medium High

1. Follow up the ironing instructions on the garment label. If there is not any instruction label,

but you know what kind of the fabric it is, please refer to the fabric setting chart in this

instruction manual.

2. The fabric setting chart is only a reference for material of base fabrics but not decoration

applied like finishes, glosses etc. Textile of which some kind of finish has been applied

(gloss, crinkle, relief etc.) should better be ironed at a lower temperature.

3. First sort laundry according to ironing temperature setting guide: woolen type, cotton

type, etc.

4. The iron heats up more quickly than it cools down. Therefore, start ironing articles from

which needs to be ironed at the lowest temperature, such as those made of synthetic

fabrics.

5. If the fabric consists of various kinds of fabrics, always select the temperature required by

the most delicate fabrics. For example, an article consists of 60% polyester and 40%

cotton, according to the fabric setting chart it should be ironed in polyester setting and

without steam.

6. If you do not know what kind of fabric the article is made of, iron a piece of the material

which is not visible when you wear to find out the appropriate temperature for your

articles.

7. Pure woolen fabrics (100% wool) should be ironed with the iron setting to steam ironing

position. It is advisable to set the temperature control knob to “Max” position and use a

dry pressing cloth covering on the woolen fabric when ironing.

8. When steam ironing woolen fabrics, shiny patches may occur. You may prevent this by

turning the article inside out and ironing the reverse side.

9. After using steam ironing on cotton fabrics, do not iron articles required by lower

temperature (such as nylon etc.) immediately. It is advisable to adjust the temperature

control knob to the lower setting; wait for about 2-8 minutes till the heating indicator light

turn on, and then you can start ironing.

Do not fill water tank with vinegar, perfume, starch, chemically descaled water or

descaling agents.

IMPORTANT HINTS:

1. Check if the rating indicated in the rating plate

corresponding to the main voltage in your home.

2. Press unlock button to lay handle down. (Fig.1)

3. Remove the protective foil or sticker or card on

the soleplate.

4. Fully unwind and straighten the power cord and

the supply hose.

5. Place the appliance on a stable, level and horizontal

surface such as ironing board.

6. Place the iron onto the iron rest plate horizontally at the base unit.

Prepare the appliance for use:

Use of the handle

1. After power on, water tank decorative indicator light will light up for easy viewing of

water level.

2. Water tank decorative indicator light lights up to indicate that the unit has been

connected to the power supply. (Fig.3)

Functions of Water tank decorative indicator light

How to use your steam station

1. Connect the appliance to a suitable socket outlet. Lay down handle and press power

switch on control panel. Water tank decorative indicator light lights up to indicate that

the unit has been connected to the power supply.

2. Set temperature control knob to desired position according to above ironing

temperature setting guide or fabric setting chart. Heating indicator light in iron unit will

turn on to indicate that the steam chamber is being heated up. When heating indicator

light turns off, it indicates that desired temperature has been reached. It is ready for

dry ironing. During use, it is normal that heating indicator light will cycle from on to off,

and then off to on. (For every first time use, it should be pre-heated for about 3

minutes)

3. After use, put iron unit back onto the base unit again, turn temperature control knob

to“MIN”. Turn off power switch on control panel.

4. Unplug the appliance from main socket.

Note: When changing your Temperature setting from higher setting to lower, it is

proposed that not to start ironing immediately since it may cause burns to your fabrics.

Please wait until heating indicator light turns on, and then turn off. It can start ironing.

Dry ironing

How to use your steam station

1. Lift the handle up and it will be locked in place when a “click” sound is heard.

(Once power is on, water tank decorative indicator light will turn off while handle is

lifting up.

2. Take the filter out from the water entrance. (Fig.7)

3. Fill the water tank to the “MAX” filling line with clean tap water. (Fig.8)

4. Put the filter back into water entrance. (Fig.9)

5. Press unlock button to lay the handle down. (Water tank decorative indicator light will

light up if power on)

6. Always pour out the remaining water after use.

Note: When the water level reaches a low level or empty, pump will make a sound to

remind you it needs refilling. Then stop using the appliance immediately and refill water

tank as the above method.

1. The filter is designed to reduce the build-up of limescale which occurs during steam ironing,

this will prolong the working life of your iron. However, please note that the filter will not

completely stop the natural process of limescale build-up.

2. The filter will need to be changed after using for about 2 months depending on your area

and hardness of the water. USING THIS IRON WITH A CLOGGED FILTER WILL DAMAGE

INTERNAL COMPONENTS. THIS MAY NOT BE COVERED BY YOUR WARRANTY.

ORDER FILTERS ONLINE AT: WWW.SWAN-BRAND.CO.UK

Fill water tank

How to use your steam station

Steam ironing

How to use your steam station

Follow the steam ironing process, and then hold the iron in vertical position about 5cm to

15cm away from the hanging fabrics. Press AND HOL:D the steam release button. This

will create vertical steam. This feature is especially used for removing creases from

hanging clothes and curtains. Never directly direct steam at people or animals. (Fig.10)

Note: Never block the steam hose.

Lift handle, take the filter out from the water tank, and then replace with a new one. (For

better performance, immerse the new filter in water for a few minutes before replacing)

(Fig.11, Fig.12)

Vertical steam ironing

1. Pump working indicator light lights up when pump is working. (No steam produced even if

pump working indicator light lights up when temperature control knob is set at “NYLON”)

(Fig.4)

2. Variable steam will emit by adjusting steam control knob on control panel. When

temperature control knob is set at “ ” or “MAX” position, steam control knob may be

set at “MIN” to “ ” range. When temperature control knob is set at “ ”, steam

control knob should be set at “MIN”. When steam control knob is set at “ ” no steam

will be emitted. If water leakage happens during use, set temperature control knob at

higher temperature position or steam control knob to lower position. (Fig.5)

3. Power switch on control panel can control circuit for complete unit. (Fig.6)

Functions of control panel

Fig.1

Fig.3

Fig.7 Fig.8

Fig.10

Filter Replacement

There is an overheat protection device installed in pump. When water in water tank has

been used up. Pump will be hot. If the temperature of pump exceeds it’s Max limit,

overheat protection will automatically activate to protect pump from being burnt out. At

this moment, turn off power switch at first, unplug the appliance from main socket, and

then check if water tank has sufficient water. If not, please refill water tank and wait 30

minutes. It will work again.

Note: When the water level reaches a low level or becomes empty, the pump will make

sound to remind you to refill it, Then stop using the appliance immediately and refill water

tank for continuous use.

Pump overheat protection function

1. Disconnect the appliance from the power supply

and allow the appliance to cool down for 60

minutes at least.

2. After use, pour out all the remaining water.

(Fig13.)

3. The iron should be placed on the iron rest, and

then store.

1. Unplug the appliance from the main supply and let the iron completely cool down.

2. Clean the iron with a damp cloth.

3. Wipe off scale and any other deposits on the soleplate with a damp cloth or non-abrasive

(liquid) cleaner. (Fig.14)

4. Never clean the appliance by running it under the tap. Never immerse any part of the

iron in water

Emptying and storing

Anti-calc system

Fig.9

Fig.4

Fig.6

Fig.5

Fig.2

Fig.11 Fig.12

Fig.13

Fig.14

Cleaning and Maintenance

Trouble shooting

1. Make sure to read all the safety precautions below and look at the

illustrations before you start using the appliance.

2. Use the appliance for its intended use only described in this manual.

3. The appliance is intended for household use only.

4. In order to protect against the risk of electric shock, do not immerse

iron power base into water or any other liquids.

5. Connect the appliance only to an alternating current of the voltage

specified on the rating plate and only to an earthed socket. To avoid a

circuit overload, do not operate another high wattage appliance in the

same circuit.

6. Turn the appliance to OFF before plugging or unplugging from outlet.

Never yank cord to disconnect from outlet; instead, grasp plug and pull

to disconnect.

7. Do not allow power cord or supply hose to touch hot surfaces.

8. Unplug the appliance from main socket before filling or emptying or

when not in use.

9. Do not operate the appliance with a damaged cord or if the appliance

has been dropped or damaged. To avoid a hazard such as the risk of

electric shock, do not disassemble the appliance, it must be taken to a

qualified serviceman or manufacturer or its service agent for

examination and repair. Incorrect re-assembly can cause a risk of

electric shock when the iron is used.

10. Place the iron out of reach of children; close supervision is necessary

for any appliance being used by or near children. Do not leave the iron

unattended while connected to the supply mains.

11. During use, always place its stand on a stable, level and horizontal

surface or ironing board.

12. Always place the iron on its stand, and do not allow the hot soleplate

touch power cord or supply hose.

13. Burns can occur from touching hot metal parts, hot water or steam.

Use caution when using the appliance.

14. Never use the iron facing towards people because the steam can

cause burns.

15. The surfaces are liable to get hot during use.

16. Never twist the supply hose during use.

17. The appliance must be used and rested on a stable, level and

horizontal surface.

18 . The iron should be placed on its stand only.

19. When placing the iron on its stand, ensure that the surface on which

the stand is placed is stable.

20. The iron is not to be used if it has been dropped, if there are visible

signs of damage or if it is leaking.

21. The iron must not be left unattended while it is connected to the supply

mains.

22. The appliance must be rest or stocked on a stable, level and horizontal

surface.

23. During use, if no water in the reservoir, it will produce noise<70dBA.

24. This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved, children shall not play with the

appliance. cleaning and user maintenance shall not be made by

children without supervision.

25. Keep the iron and its cord out of reach of children less than 8 years of

age when it is energised or cooling down.

Never dispose of your product with other household waste.

Please inform yourself about the local rules on the separate

collection of electrical and electronic products. The correct

disposal of your old product helps prevent potentially negative

consequences on the environment and human health.

Handle attached to the base unit is used for carrying the appliance; it also serves as a

power switch: Lift the handle up, it will be powered OFF. Lay the handle down, then power

ON. Before use, please lay the handle down as follows: Press down two unlock buttons at

the same time to lay down the handle. After use, allow the appliance completely cool down,

put the iron on base. Lift handle up. There will be a “click” sound heard to indicate the

handle has been locked in place and you can carry the appliance by the handle. (Fig.2)

Steam Generator Iron

Model SI9050N

Need help with this product?

Do not return it to the store. Call service

0871 200 0003

No power

1. Is it plugged in?

2. Is the carry handle down. It has to be down or the unit won’t power up!

3. Is it switched on?

No steam

1. Is thermostat set to or ? Lower settings won’t produce steam

2. Have you turned the steam control knob up far enough?

3. You need to press and HOLD the steam switch on the handle for up to

30 seconds, particularly on first use. This to allow the pump to expell any

airlocks in the pipe. You will be able to tell when steam is about to come

through because the tone of the pump will change and become quieter.

Still no joy?

It doesn’t mean your product is faulty. Call service! It’s quicker than taking

it back to the shop and they can get you up and running in more than 99%

of cases!

Service phone number is:

0871 200 0003

Est.1931

We love

what we do

2 year

GUARANTEE

we’re proud

of our quality

Scan this QR code

to hear about

our story

Find us on Facebook

Swan Products Ltd. PO Box 3117, Stoke-on-Trent ST4 9GD

www.swan-brand.co.uk

Product specificaties

Merk:	Swan
Categorie:	Stoomgenerator
Model:	SI9050

Heb je hulp nodig?

Als je hulp nodig hebt met Swan SI9050 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Stoomgenerator Swan

Swan SI9021 Handleiding

18 Februari 2023

Swan SI4060 Handleiding

18 Februari 2023

Swan SI4030 Handleiding

18 Februari 2023

Swan SI12010 Handleiding

18 Februari 2023

Swan SI11010 Handleiding

18 Februari 2023

Swan SI9060 Handleiding

18 Februari 2023

Swan SI9050 Handleiding

18 Februari 2023

Swan SI9020 Handleiding

18 Februari 2023

Handleiding Stoomgenerator

Nieuwste handleidingen voor Stoomgenerator

Calor GV9560- PRO EXPRESS ULTIMATE Stoomgenerator Handleiding

29 September 2023

Calor GV9561- PRO EXPRESS ULTIMATE Stoomgenerator Handleiding

29 September 2023

Calor GV9563- PRO EXPRESS ULTIMATE Stoomgenerator Handleiding

29 September 2023

Calor GV9568 - PRO EXPRESS ULTIMATE Stoomgenerator Handleiding

29 September 2023

Calor GV9562- PRO EXPRESS ULTIMATE Stoomgenerator Handleiding

29 September 2023

Exquisit BS3101 Handleiding

20 September 2023

Herzberg HG-8039 Handleiding

21 Augustus 2023

Mio Star Continua III Handleiding

29 Augustus 2023

Dunlop Draagbare Stoomreiniger Item 06975 Handleiding

19 Augustus 2023

Domo DO1096S Handleiding

9 Augustus 2023