Sunding SD-581C Handleiding

Bekijk gratis de handleiding van Sunding SD-581C (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 17 mensen en kreeg gemiddeld 4.1 sterren uit 4 reviews. Heb je een vraag over Sunding SD-581C of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CLK Mode(12H/24H)

Computer Battery Installation

While the default Maintenance Alert digit

200RIGHTkm/m is flashing, Press the button

to choosekm/m. Press the 200/400/600/800LEFT

button to confirm and enter into mode. BASICALL Orselect

(when the the Maintenance Alert digit you set, the ODO

will appear on the screen to alert the rider, press theRIGHT

button seconds to cancel it.)3

24 Function

Instruction Manual V0.1

Remove the battery cover from the bottom of the computer by using a

flat blade screwdriver, install battery with the positive (+) pole facing the

battery cover and replace the cover. Should the LCD show irregular

figures, take out the battery and reinstall it.

Attach the mounting shoe with the cable ties

to the handlebars as shown in the diagram.

Attach the computer to the mounting shoe

by sliding the unit until it snaps firmly into

position. To remove, press down on the

release catch, and remove the computer. To

check for proper speed function and sensor

alignment, spin the front wheel with the

computer in speed mode. Adjust the position

of sensor and magnet if there is on or weak

signal.

Computer

Long press + button for 3 seconds to enter setting modeLEFTRIGHT.

‘’ appears on the screed when the battery has been installed, with 2060

one figure flashing enter the wheel circumference using the formula

below.

In the example above you would enter . Press the button to 2198RIGHT

advance the digits as needed and the button to confirm and LEFT

advance. (The circumference ranges 0mm~9999mm), press the LEFT

button to enter mode.KM/M

Setting(km/h)/(m/h)

Press the button to choose or .RIGHTkm/hm/h

Press the button to enter mode.LEFTCLOCK

Setting Maintenance alert

In CLOCK Mode, press the button for seconds LEFT3

to enter 12/24H selection. Press once more to swap

between 12/24 hours. Press the RIGHT button to enter

the Hour mode, when the figure indicating HOUR starts

to flash, press the LEFT button to adjust it. Continue to

press the RIGHT button to enter the Minute mode, when the figure

indicating MINUTE starts to flash, press the LEFT button to adjust. Press

the RIGHT button to confirm & press the RIGHT button again to switch to

ODO mode.

SD-581C Bicycle Computer

Installation of Speedometer

Attach speedometer sensor to the front fork using the ties. The

computer and sensor should be installed on the same side of the

fork, with distance between them of less than 60cm. The arrow

on the sensor should point at the magnet. Install magnet as

shown in figure. Distance between sensor and magnet should

be 3.0mm.

NOOFF

-SPD Current Speed

- ODO Odometer (0~99999km/m)

- DST Trip Distance

- MXS Maximum Speed

-AVS Average Speed

- TM Elapsed Time

- CLK Clock (12H/24H)

- TMP Temperature / (-10°C~70°C)

- MIN TMP Minimum Temperature

- MAX TMP Maximum Temperature

-CAL Calories Expended

- FAT Fat Burned

-SCAN

- “+”“-”Comparator

- SETTING SPEED SCALE (km/h,m/h)

- SETTING TYRE CIRCUMFERENCE / (0mm~9999mm)

- SETTING THE LAST VALUE OF ODOMETER / ODO

- MAINTENANCE ALERT

-FREEZE FRAME MEMORY

-LOW BATTERY INDICATOR

-BASIC OR ALL

-SMART BACKLIGHT

-BACKLIGHT IS LONG BRIGHT

- AUTO ON/OFF

Setting Rider’s Weight

The default weight is 65kg, press the button to adjust the RIGHT

flashing weight number according to rider’s weight, press buttonLEFT

to confirm and advance. Weight ranges : 20~150kg. Press the LEFT

button to enter into Maintenance Alert setting.

Computer

Sensor

Magnet

Notice

Pass bicycle spokes through the

plastic hole on the bottom of the

magnet and tighten to secure

The magnet is designed for

spokes that are less than

2mm thick.

FUNCTIONS

Mounting Shoe

Installation

Parameter Settings

Wheel Size Input

3.0mm

BASIC Or ALL

Press the RIGHT button select BASICORALL, Press the LEFT

button to confirm and enter into Clock mode. “BASIC”Indicates that the

menu displays basic functions except for MINTMP\ MAXTMP\ and CAL

FAT.

“ALL” Indicates that the menu displays all functions including MINTMP\

MAXTMP\ CALFAT and .

Product specificaties