Sunding SD-579 Handleiding

Bekijk gratis de handleiding van Sunding SD-579 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 4.0 sterren uit 7 reviews. Heb je een vraag over Sunding SD-579 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

-TRIP UP TRIP DISTANCE COUNTUP

-TRIP DN TRIP DISTANCE COUNTDOWN

-CAL CALORIE

-FAT FATBURN

-COMPARATOR

-Km/Mile SELECTION

-SLEEP MODE

- MAINTENANCE ALERT

- SETTING TYRE CIRCUMFERENCE

-SETTING LAST VALUE OF ODOMETER/ODO

-SETTING TTM

-COMPUTER LOW BATTERY INDICATOR

-SENSOR LOW BATTERY INDICATOR

- AUTO BACK LIGHT

-WIRELESS AUTO WAKE UP

- AUTO ON/OFF

SD579C- V1.0

FUNCTIONS ILLUSTRATIONS

WHAT IS IN THE PACKAGE

COMPONENT ILLUSTRATIONS

-SPD CURRENT SPEED

-ODO ODOMETER

-DST TRIP DISTANCE

-MXS MAXIMUM SPEED

-AVS AVERAGE SPEED

-TTM TOTAL TRIP TIME

-TM TRIP TIME

-RAT RIDING ALL TIME (SINGLE TRIP TIME)

-CLK CLOCK 12H/24H

-SW STOPWATCH

-Th TEMPERATURE

-MAX Th MAXIMUM TEMPERATURE

-MIN Th MINIMUM TEMPERATURE

-TM UP TRIP TIME COUNT UP

-TM DN TRIP TIME COUNT DOWN

1

2

3

5

6

4

3mm

Computer unit and mount installation

2

To attach the speedometer sensor, use the ties to secure it to the front

fork. Make sure the computer and the sensor are on the same side of

the fork and no more than 60cm apart. The sensor should have an

arrow pointing at the magnet. Follow the figure to install the magnet on

a spoke. The gap between the sensor and the magnet should be 3 mm.

Notice

The magnet is designed for spokes

that are less than 2mm thick

Pass bicycle spokes through the

plastic hole on the bottom of the

magnet and tighten to secure

Computer

CR2032 Battery

Magnet

Mounting Shoe

Sensor

Ties

1

2

3

4

5

6

Please note that the slight noise when the computer unit shakes is the built-in ball switch, which is a

normal phenomenon caused by the wireless automatic wake-up function design.

Installation diagram of

magnet and Sensor

INSTRUCTION

Avoid exposing the device to direct sunlight or high temperature for too

long. Let it cool down in the shade for a while.

3.Black display

4.Display shows incomplete figures.

5.Display readout fades out

1.The speedometer shows 0 km/h while riding.

Improper magnet/sensor alignment, or the distance between

the computer and the sensor is more than 80cm.

2.The speedometer shows wrong values.

Take out the battery and reset it after 10 seconds.

Poor battery contact or dead battery .Check the installation of the battery or change a new battery.

The battery voltage is low, change a new battery.

MALFUNCTIONS AND REASONS

MODE INSTRUCTION

After inserting the battery, the screen enters the total distance/time mode. Press the MODE button to cycle through single

distance/time mode, count up/down mode and fat/calorie mode in turn. In the total distance/time mode, count up/down

mode and fat/calorie mode, it will automatically return to the single distance/time modeafter 8 seconds of no operation.

ODO / TTM MODEDST / TM MODECAL / FAT MODECOUNTUP / DOWNMODE

1

FRONTBACK

COMPUTER &

MOUNTING

SHOE TRIGGER

BATTERY

COVER

MAINTENANCEALERT

COMPARATOR

LOWBATTERYINDICATOR

Computer unit interface

MODESET

SPEED

TIME

Computer battery

installation: Open the

battery cover. Install

CR2032 batteries with

positive poles facing

battery cover.

Match base alignment with

computer and insert to attach.

Thread ties through the slots under

the base to attach to handlebar.

Product specificaties