StarTech.com VID2VGATV3 Handleiding

StarTech.com Audio/video-converter VID2VGATV3

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com VID2VGATV3 (2 pagina's) in de categorie Audio/video-converter. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 19, 2019 3:38 PM

Product Diagram (VID2VGATV3)

Front and Side Prole

Rear and Side Prole

Component Function

1Video Input Selection Switch • Select the Source Device Video Signal

2VGA Output Port • Connect a VGA Video Display Device

3Resolution Selection Button • Select the Output Resolution

4Power Port • Connect a Power Source

5Composite Video Input Port • Connect a Composite Video Source Device

6S-Video Input Port • Connect an S-Video Source Device

Composite and S-Video to VGA Video Converter

Requirements

For the latest requirements, please visit . www.startech.com/VID2VGATV3

• Composite Video or S-Video Source Device x 1

• Composite Video or S-Video Cable x 1

• VGA Video Display Device x 1

• VGA Cable x 1

• USB Power Source x 1

Installation and Operation

1. Ensure all of your are powered o.Devices

2. Determine if you are using a or . Toggle the Composite S-Video Source Device

Video Input Selection Switch Source Device to match your video signal.

3. Connect a to the . Composite Video Cable Composite Video Input Port

Connect an to the . S-Video Cable S-Video Input Port

4. Connect the other end of the to the Composite Video Cable Composite Video

Source Device.

Connect the other end of the to the . S-Video Cable S-Video Source Device

5. Connect a to the on the .VGA Cable VGA Output Port Video Converter

6. Connect the other end of the to the .VGA Cable VGA Video Source Device

7. Connect the to an available and to USB-A to USB Mini Cable USB Power Source

the .Power Port

8. Select the output resolution by pressing the until the Resolution Selection Button

desired resolution is met. Each time you press the the Resolution Selection Button

new resolution settings will appear on the in the upper On Screen Display (OSD)

right-hand corner of the screen.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

Product specificaties

Merk:	StarTech.com
Categorie:	Audio/video-converter
Model:	VID2VGATV3
Kleur van het product:	Zwart
Gewicht:	48 g
Breedte:	58 mm
Diepte:	66 mm
Hoogte:	20 mm
Gewicht verpakking:	100 g
Breedte verpakking:	113 mm
Diepte verpakking:	150 mm
Hoogte verpakking:	28 mm
Materiaal behuizing:	Kunststof
Meegeleverde kabels:	USB
Certificering:	CE, FCC, REACH
Maximale refresh snelheid:	60 Hz
Maximale videoresolutie:	1920 x 1200 Pixels
Videoresoluties:	800 x 600,1024 x 768,1280 x 1024,1600 x 1200,1680 x 1050,1920 x 1080,1920 x 1200 Pixels
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-10 - 80 °C
Snelle installatiehandleiding:	Ja
Stroomvoorziening via USB:	Ja
Hostinterface:	Composite + S-Video
(Buitenste) hoofdverpakking hoogte:	450 mm
(Buitenste) hoofdverpakking breedte:	327 mm
(Buitenste) hoofdverpakking lengte:	400 mm
Hoeveelheid per (buitenste) hoofdverpakking:	100 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Type converter:	Actieve video-omzetter
Output interface:	VGA