Speco Technologies O4P30X2 Handleiding

Speco Technologies Bewakingscamera O4P30X2

Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies O4P30X2 (64 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/64

User Manual

4MP PTZ Network Camera

O4P30X2

Please read this instruction carefully before operating the unit keep it for further reference and

1. Electrical safety

All installation and operation here should conform to local electrical safety codes.

Use a certified/listed 12VDC/DC24V/AC24V power supply only.

Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The

product must be grounded to reduce the risk of electric shock.

Improper handling and/or installation could run the risk of fire or electrical shock.

2. Environment

Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage, and installation.

This product should be installed in a cool, dry place away from direct sunlight and heat sources.

Do not install the product in extreme temperature conditions.

Do not expose the camera to electromagnetic radiation. Otherwise, it may result in CMOS sensor failure.

Do not block any ventilation openings.

Do not allow water and liquid intrusion into the camera.

3. Operation and Daily Maintenance

Please shut down the device and then unplug the power cable before you begin any maintenance work.

Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.

Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of neutral

detergent. Finally use the dry cloth to clean the device.

Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may

result in poor IR functionality and/or IR reflection.

The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.

Dome cover is an optical device, please do not touch or wipe cover surface directly during installation and use, please refer to the

following methods if dirt is found.

Stained with dirt:

Use oil-free soft brush or hair dryer to remove it gently.

Stained with grease or fingerprint.

Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and

wipe several times if it is not clean enough.

Warning

This camera should be installed by qualified personnel only.

All the examination and repair work should be done by qualified personnel.

Any unauthorized changes or modifications could void the warranty.

Statement

This guide is for reference only.

Product, manuals, and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these

without notice and without incurring any obligation.

Speco Technologies is not liable for any loss caused by improper operation.

Regulatory Information

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

⚫ This device may not cause harmful interference.

⚫ This device must accept any interference received, including interference that may cause undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

⚫ Reorient or relocate the receiving antenna.

⚫ Increase the separation between the equipment and receiver.

⚫ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Note:

Before installation, check the package and make sure that all components are included.

Contact your rep or Speco customer service department immediately if something is broken or missing in the package.

Product specificaties

Merk:	Speco Technologies
Categorie:	Bewakingscamera
Model:	O4P30X2

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies O4P30X2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Speco Technologies

Speco Technologies VLDT3GM Handleiding

6 Juli 2023

Speco Technologies CVC624WDR Handleiding

1 Juli 2023

Speco Technologies ZIPTW4B1 Handleiding

27 Juni 2023

Speco Technologies O2ID21M Handleiding

26 Juni 2023

Speco Technologies Intensifier 2 CVC6246iHR Handleiding

26 Juni 2023

Speco Technologies O4DT1 Handleiding

25 Juni 2023

Speco Technologies O4iB2 Handleiding

25 Juni 2023

Speco Technologies O8D8M Handleiding

22 Juni 2023

Speco Technologies CVC5100BPVFW Handleiding

21 Juni 2023

Speco Technologies VLBT6W Handleiding

21 Juni 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Aqara Camera Hub G2H Handleiding

28 April 2024

Iiquu Dummy Dome Camera Handleiding

28 April 2024

Sony SNC-VB640 Handleiding

26 April 2024

Sony SNC-EB642R Handleiding

26 April 2024

Sony SNC-VB642D Handleiding

26 April 2024

Sony SRG-HD1 Handleiding

26 April 2024

Sony SNC-ZM550 Handleiding

26 April 2024

Sony SNC-EM642R Handleiding

26 April 2024

Sony SNC-EM641 Handleiding

26 April 2024

Sony SNC-ZB550 Handleiding

26 April 2024