Speco Technologies O2VB1N Handleiding

Speco Technologies Bewakingscamera O2VB1N

Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies O2VB1N (42 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/42

User Manual

2MP IP Camera

O2VB1/O2V V/O2VT1/O2V V B1 T1

Please read this instrucon carefully before operang the unit keep it for further reference and

Important Safeguards and Warnings

1. Electrical safety

All installaon and operaon here should conform to local electrical safety codes.

Use a cered/listed 12VDC Class2 power supply only.

Please note: Do not connect two power supplying sources to the device at the same me; it may result in device damage!

The product must be grounded to reduce the risk of electric shock.

Improper handling and/or installaon could run the risk of re or electrical shock.

2. Environment

Heavy stress, violent vibraon or exposure to water is not allowed during transportaon, storage and installaon.

This product should be installed in a cool, dry place away from direct sunlight and heat sources.

Do not install the product in extreme temperature condions.

Do not expose the camera to electromagnec radiaon. Otherwise it may result in CMOS sensor failure.

Do not block any venlaon openings.

Do not allow water and liquid intrusion into the camera.

3. Operaon and Daily Maintenance

Please shut down the device and then unplug the power cable before you begin any maintenance work.

Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.

Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of

neutral detergent. Finally use the dry cloth to clean the device.

Please use a professional opcal cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth)

may result in poor IR funconality and/or IR reecon.

The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.

Dome cover is an opcal device, please don t touch or wipe cover surface directly during installaon and use, please refer to ’

the following methods if dirt is found.

Stained with dirt:

Use oil-free so brush or hair dryer to remove it gently.

Stained with grease or ngerprint

Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth

and wipe several mes if it is not clean enough.

Warning

This camera should be installed by qualied personnel only.

All the examinaon and repair work should be done by qualied personnel.

Any unauthorized changes or modicaons could void the warranty.

Statement

This guide is for reference only.

Product, manuals and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify

these without noce and without incurring any obligaon.

Speco Technologies is not liable for any loss caused by improper operaon.

Regulatory Informaon

FCC condions:

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received, including interference that may cause undesired operaon.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause

harmful interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular

installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separaon between the equipment and receiver.

 Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

Note:

Before installaon, check the package and make sure that all components are included.

Contact your rep or Speco customer service department immediately if something is broken or missing in the package.

Accessory name

Amount

Network Camera Unit

Juncon Box

Quick Start Guide

Installaon Accessories Bag

Product specificaties

Merk:	Speco Technologies
Categorie:	Bewakingscamera
Model:	O2VB1N

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies O2VB1N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Speco Technologies

Speco Technologies VLDT3GM Handleiding

6 Juli 2023

Speco Technologies CVC624WDR Handleiding

1 Juli 2023

Speco Technologies ZIPTW4B1 Handleiding

27 Juni 2023

Speco Technologies O2ID21M Handleiding

26 Juni 2023

Speco Technologies Intensifier 2 CVC6246iHR Handleiding

26 Juni 2023

Speco Technologies O4DT1 Handleiding

25 Juni 2023

Speco Technologies O4iB2 Handleiding

25 Juni 2023

Speco Technologies O8D8M Handleiding

22 Juni 2023

Speco Technologies CVC5100BPVFW Handleiding

21 Juni 2023

Speco Technologies VLBT6W Handleiding

21 Juni 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Aqara Camera Hub G2H Handleiding

28 April 2024

Iiquu Dummy Dome Camera Handleiding

28 April 2024

Sony SNC-VB640 Handleiding

26 April 2024

Sony SNC-EB642R Handleiding

26 April 2024

Sony SNC-VB642D Handleiding

26 April 2024

Sony SRG-HD1 Handleiding

26 April 2024

Sony SNC-ZM550 Handleiding

26 April 2024

Sony SNC-EM642R Handleiding

26 April 2024

Sony SNC-EM641 Handleiding

26 April 2024

Sony SNC-ZB550 Handleiding

26 April 2024