Sony WS-X10FB Handleiding

Sony Accessoires WS-X10FB

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony WS-X10FB (2 pagina's) in de categorie Accessoires. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
© 2007 Sony Corporation Printed in Malaysia
Owner’s Record
The model and serial numbers are located at the
bottom of the unit. Record the serial number in the
space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Model No. WS-X10FB
Serial No.______________
Precautions
This product is for DAV-X10 only. Use with other
products or for other purposes than those specified
may cause damage or injury.
On safety
Recommended for use with the Sony small
speaker system.
Be sure to place the speaker stand in a flat,
horizontal place.
On placement
Use caution when placing the stand on a specially
treated (waxed, oiled, polished, etc.) floor, as
staining or discoloration may result.
On cleaning
Clean the pipe stand, the base, and the bracket with
a soft cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as thinner,
benzene or alcohol.
If you have any questions or problems concerning
your system, please consult your nearest Sony
dealer.
Assembly
Adjust the height of the pipe stand, and
then attach the speaker to the stand.
When no adjustment is necessary, go to 3.
1 Remove the speaker cord from the cable holder
of the pipe stand.
2 Loosen the two screws attached to the pipe
stand, and adjust the pipe stand to a height of
766 mm to 980 mm. After adjusting, tighten
the screws. After adjusting the height of the
pipe stand, insert the speaker cord in the cable
holder again.
3 After connecting the speaker cord to the
speaker, tightly secure the speaker to the mount
with the supplied screw.
Specifications
Dimension (w/h/d) Approx. 280
×
766 - 980
×
280 mm
(
11
1/8
× 30 1/4
-
38
5/8 ×
11
1/8 in.
)
280
×
875 - 1090
×
280
mm
(
11
1/8
× 34 1/2
-
43 × 11
1/8 in.
) (w/h/d) with
speaker
(Diameter of base: 280
mm (
11
1/8 in.
))
Mass Approx. 4.2 kg
(9 lb 5 oz)
Supplied accessories
Screw (2)
Design and specifications are subject to change
without notice.
English Français
Précautions
Ce produit est destiné uniquement au DAV-X10.
Lutilisation avec d’autres produits ou à des fins
autres que celles spécifiées peut provoquer des
dégâts ou des blessures.
Sécurité
Utilisation recommandée avec le système de petits
haut-parleurs Sony.
Veillez à placer le support d’enceinte sur une
surface plane et horizontale.
Installation
Soyez particulièrement prudent lorsque vous placez
le support sur une surface ayant subi un traitement
spécial (cirée, huilée, polie, etc.), car il peut laisser
des taches ou entraîner la décoloration du
revêtement de sol.
Entretien
Nettoyez le tube socle, la base et l’applique avec un
chiffon doux légèrement imprégné dune solution
détergente douce. N’utilisez aucun type de tampon
abrasif, de poudre à récurer ou de solvant comme
du dissolvant, du benzène ou de lalcool.
Pour toute question ou tout problème concernant
votre chaîne, nhésitez pas à consulter votre
revendeur Sony le plus proche.
Montage
Réglez la hauteur du tube socle, puis fixez
l’enceinte sur le socle. Si aucun réglage
nest nécessaire, allez à l’étape 3.
1 Retirez le cordon de l’enceinte du protège-
câbles du tube socle.
2 Desserrez les deux vis fixées au tube socle, puis
réglez la hauteur du tube socle entre 766 mm et
980 mm. Une fois le réglage terminé, resserrez
les vis. Une fois la hauteur du tube socle réglée,
replacez le cordon de l’enceinte dans le protège-
câbles.
3 Après avoir raccordé le cordon de l’enceinte à
l’enceinte, fixez solidement lenceinte au support
à l’aide de la vis fournie.
Caractéristiques
Dimensions (l/h/p) Environ 280
×
766 - 980
×
280 mm
(
11
1/8
× 30 1/4
-
38
5/8 ×
11
1/8 po.
)
280
×
875 - 1090
×
280
mm
(
11
1/8
× 34 1/2
-
43 × 11
1/8 po.
) (l/h/p) enceinte
comprise
(Diamètre de la base :
280 mm (
11
1/8 po.
))
Poids Environ 4,2 kg
(9 li. 5 on.)
Accessoires fournis
Vis (2)
La conception et les spécifications sont sujettes à
modification sans préavis.
Deutsch
Sicherheitsmaßnahmen
Dieses Produkt ist ausschließlich für die DAV-X10
konzipiert. Bei Verwendung mit anderen
Produkten oder zu einem anderen als dem
vorgesehenen Zweck besteht die Gefahr von
Verletzungen bzw. Sachschäden.
Sicherheit
Empfohlen zur Verwendung mit einem
Kompaktlautsprechersystem von Sony.
Bitte stellen Sie den Lautsprecherständer auf eine
ebene, waagrechte Fläche.
Aufstellung
Seien Sie vorsichtig, wenn Sie den Ständer auf
einen besonders behandelten Fußboden (gewachst,
geölt, poliert usw.) stellen, da es zu Flecken oder
Verfärbungen kommen kann.
Reinigung
Reinigen Sie den Rohrständer, den Fuß und den
Montagebügel mit einem weichen Tuch, das Sie
leicht mit einer milden Reinigungslösung
angefeuchtet haben. Verwenden Sie keine
Scheuermittel, Scheuerschwämme oder
Lösungsmittel wie Verdünnung, Benzin oder
Alkohol.
Sollten am System Probleme auftreten oder sollten
Sie Fragen haben, wenden Sie sich bitte an Ihren
Sony-Händler.
Montage
Stellen Sie die Höhe des Rohrständers ein
und befestigen Sie den Lautsprecher am
Ständer. Wenn keine Einstellung
erforderlich ist, fahren Sie mit Schritt 3
fort.
1 Entfernen Sie das Lautsprecherkabel vom
Kabelhalter des Rohrständers.
2 Lösen Sie die beiden Schrauben am
Rohrständer und stellen Sie den Rohrständer
auf eine Höhe von 766 mm bis 980 mm ein.
Ziehen Sie nach dem Einstellen die Schrauben
an. Führen Sie nach Einstellen der Höhe des
Rohrständers das Lautsprecherkabel erneut in
die Kabelhalterung ein.
3 Wenn Sie das Lautsprecherkabel an den
Lautsprecher angeschlossen haben, fixieren Sie
den Lautsprecher mit der mitgelieferten
Schraube am Ständer.
Technische Daten
Abmessungen (B/H/T) ca. 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (B/H/T) mit
Lautsprecher
(Durchmesser des
Standfußes: 280 mm)
Gewicht ca. 4,2 kg
Mitgeliefertes Zubehör
Schraube (2)
Änderungen, die dem technischen Fortschritt
dienen, bleiben vorbehalten.
Precauciones
Este producto es sólo para DAV-X10. El uso con
otros productos o para otros fines distintos de los
especificados puede producir lesiones o daños.
Seguridad
Recomendado para su uso con el sistema de
altavoces pequeños Sony.
Asegúrese de colocar el soporte del altavoz en un
lugar plano y horizontal.
Ubicación
Tenga cuidado si coloca el soporte en suelos con un
tratamiento especial (encerados, barnizados con
aceites, pulidos, etc.), ya que es posible que
aparezcan manchas o se descoloren.
Limpieza
Limpie el tubo de soporte, la base y el soporte con
un paño suave ligeramente humedecido con una
solución detergente poco concentrada. No utilice
ningún estropajo abrasivo, detergente concentrado
ni disolventes como diluyentes, bencina o alcohol.
Si tiene dudas o problemas sobre el sistema de
altavoces, póngase en contacto con el proveedor
Sony más cercano.
Montaje
Ajuste la altura del tubo de soporte y, a
continuación, fije el altavoz al soporte. Si
no es necesario realizar ningún ajuste,
vaya al paso 3.
1 Extraiga el cable del altavoz del fijador de cables
del tubo de soporte.
2 Afloje los dos tornillos fijados al tubo de
soporte y ajústelo a una altura de 766 mm a 980
mm. Una vez ajustado, fije los tornillos. Tras
ajustar la altura del tubo de soporte, inserte el
cable del altavoz en el fijador de cables de
nuevo.
3 Después de conectar el cable del altavoz al
altavoz, fije firmemente el altavoz al soporte de
montaje con ayuda del tornillo suministrado.
Especificaciones
Dimensiones (an/al/prf) Aprox. 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (an/al/prf) con
altavoz
(Diámetro de la base:
280 mm)
Masa Aprox. 4,2 kg
Accesorios suministrados
Tornillo (2)
El diseño y las especificaciones están sujetos a
cambios sin previo aviso.
Español
1
766 mm - 980 mm
(30
1
/
4
in. - 38
5
/
8
in.)
2 3
Speaker Stand
WS-X10FB
3-210-548-11(1)
(1)
Voorzorgsmaatregelen
Dit product mag alleen samen met de DAV-X10
worden gebruikt. Gebruik met andere producten of
voor andere doeleinden dan deze vermeld, kan tot
schade of verwondingen leiden.
Veiligheid
Aanbevolen voor kleine Sony luidsprekers.
Plaats de luidsprekerstandaard op een vlakke,
horizontale plek.
Opstelling
Ga voorzichtig tewerk wanneer u de standaard op
een speciaal behandelde vloer (met was of olie
behandeld, gepolijst, enzovoort) plaatst; anders
kunnen vlekken of verkleuringen optreden.
Reinigen
Reinig de stang, de voet en de steun met een zachte
doek die lichtjes is bevochtigd met een zacht
zeepsopje. Gebruik geen schuursponsje,
schuurpoeder of oplosmiddelen, zoals thinner,
benzine of alcohol.
Mocht u vragen of problemen met uw systeem
hebben, aarzel dan niet om contact op te nemen
met de dichtstbijzijnde Sony handelaar.
Montage
Pas de hoogte van de stang aan en
bevestig vervolgens de luidspreker aan
de standaard. Wanneer geen
aanpassingen nodig zijn, ga naar 3.
1 Verwijder de luidsprekerkabel van de
kabelhouder op de stang.
2 Maak de twee schroeven bevestigd aan de stang
los en pas de stang aan op een hoogte van 766
mm tot 980 mm. Na de aanpassingen draait u
de schroeven vast. Nadat u de lengte van de
stang hebt aangepast, bevestigt u de
luidsprekerkabel opnieuw in de kabelhouder.
3 Nadat u de luidsprekerkabel hebt verbonden
met de luidspreker, bevestigt u de luidspreker
goed op de steun met behulp van de
bijgeleverde schroef.
Specificaties
Afmetingen (b/h/d) Circa 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (b/h/d) met
luidspreker
(Diameter van voet: 280
mm)
Gewicht Circa 4,2 kg
Meegeleverde accessoires
Schroef (2)
Ontwerp en specificaties zijn onderhevig aan
wijzigingen zonder voorafgaande kennisgeving.
Nederlands
Försiktighetsåtgärder
Denna produkt är endast avsedd för DAV-X10.
Användning med andra produkter eller för andra
syften än de som anges kan orsaka materiella
skador eller personskador.
Om säkerhet
Rekommenderas för små Sony-högtalare.
Se till att placera högtalaren på en plan,
horisontell plats.
Om placering
Var försiktig när du placerar stativet på ett
specialbehandlat (vaxat, oljat, polerat etc.) golv
eftersom det kan fläckas eller missfärgas.
Om rengöring
Rengör rörstativet, bottenplattan och fästet med en
mjuk duk lätt fuktad med ett milt rengöringsmedel.
Använd inga typer av skurdukar, skurpulver eller
lösningsmedel som t.ex. thinner, bensen eller
alkohol.
Om du har frågor eller problem gällande ditt
system, vänligen rådfråga din närmsta Sony-
återförsäljare.
Montering
Ställ in rörstativets höjd och fäst sedan
högtalaren i stativet. Gå till punkt 3 om
det inte behövs några justeringar.
1 Lossa högtalarkabeln från kabelhållaren på
rörstativet.
2 Lossa de två skruvarna från rörstativet och
justera stativet till en höjd mellan 766 mm och
980 mm. Dra åt skruvarna efter justering. Sätt
tillbaka högtalarkabeln i kabelhållaren igen, när
rörstativets höjd justerats.
3 r du har anslutit högtalarkabeln till
högtalaren drar du åt högtalaren i fästet
ordentligt med den medföljande skruven.
Tekniska data
Dimensioner (b/h/d) Cirka 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (b/h/d) med
högtalare
(Basens diameter: 280
mm)
Vikt Cirka 4,2 kg
Medföljande tillbehör
Skruv (2)
Design och tekniska data kan ändras utan
meddelande.
Svenska
Środki ostrożności
Ten produkt jest przeznaczony tylko do współpracy
z urządzeniem DAV-X10. Używanie go z innymi
produktami lub do innych celów niż opisane w tej
instrukcji może spowodować uszkodzenie
produktu lub obrażenia użytkownika.
O bezpieczeństwie
Zalecany do stosowania z zestawem małych
głośników Sony.
Głośnik należy umieścić na płaskiej poziomej
powierzchni.
O lokalizacji
Umieszczając głośnik na specjalnie zabezpieczonej
podłodze (pokrytej woskiem, olejem, pastą itp.),
należy zachować ostrożność, ponieważ może to
spowodować jego poplamienie lub odbarwienie.
O czyszczeniu
Stojak, podstawę i wspornik należy czyścić przy
pomocy miękkiej ściereczki lekko zwilżonej
roztworem łagodnego detergentu. Nie stosować
szorstkich ściereczek, proszku do szorowania ani
rozpuszczalników, takich jak rozcieńczalnik,
benzen czy alkohol.
W przypadku jakichkolwiek pytań lub problemów
związanych z zestawem głośników skontaktuj się z
najbliższym punktem sprzedaży sprzętu firmy
Sony.
Montaż
Wyreguluj wysokość stojaka i zamocuj na
nim głośnik. Jeżeli regulacja nie jest
wymagana, przejdź do punktu 3.
1 Wyjmij przewód głośnika z oprawy w stojaku z
rury.
2 Poluźnij dwie śruby stojaka z rury i wyreguluj
wysokość stojaka w zakresie od 766 do 980
mm. Po zakończeniu regulacji dokręć śruby.
Następnie włóż przewód głośnika ponownie w
oprawę.
3 Po podłączeniu przewodu do głośnika należy
mocno dokręcić głośnik do konstrukcji za
pomocą śruby dołączonej do zestawu.
Dane techniczne
Wymiary (s/w/g) Ok. 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (s/w/g) z
głośnikiem
(Średnica podstawy:
280 mm )
Waga Ok. 4,2 kg
Akcesoria wchodzące w skład zestawu
Śruba (2)
Wygląd i dane techniczne mogą ulec zmianie bez
uprzedniego powiadomienia.
Język polski
Precauzioni
Il prodotto è utilizzabile esclusivamente con DAV-
X10. Luso con altri prodotti o per scopi diversi da
quelli specificati può provocare danni e lesioni.
Sicurezza
Da utilizzare con il sistema diffusori Sony di
dimensioni ridotte.
Si raccomanda di posizionare il supporto per
diffusori su una superficie piana e orizzontale.
Installazione
Prestare attenzione nel collocare il supporto su un
pavimento trattato con prodotti speciali (quali cera,
olio o lucidanti), onde evitare macchie o
scolorimento.
Pulizia
Pulire lasta, la base e la staffa con un panno
morbido leggermente inumidito con una soluzione
detergente neutra. Non utilizzare alcun tipo di
spugnetta o polvere abrasiva, né solventi quali
diluente, benzina o alcol.
Per qualsiasi domanda o problema riguardante il
sistema, rivolgersi al rivenditore Sony più vicino.
Assemblaggio
Regolare l’altezza dell’asta e collegarvi il
diffusore. Se non è necessario effettuare
la regolazione, passare al punto 3.
1 Rimuovere il cavo dei diffusori dal fermacavo
dell’asta.
2 Allentare le due viti collegate all’asta e regolarla
ad unaltezza da 766 mm a 980 mm. Dopo la
regolazione, serrare nuovamente le viti. Dopo
aver regolato laltezza dellasta, reinserire il cavo
dei diffusori nel fermacavo.
3 Dopo aver collegato il cavo al diffusore, fissare
saldamente il diffusore al supporto mediante la
vite in dotazione.
Caratteristiche tecniche
Dimensioni (l/a/p) Circa 280
×
766 - 980
×
280 mm
280
×
875 - 1090
×
280
mm (l/a/p) con
diffusore
(Diametro della base:
280 mm)
Peso Circa 4,2 kg
Accessori in dotazione
Viti (2)
Il design e le caratteristiche tecniche sono soggetti a
modifiche senza preavviso.
Italiano
1
2 3
766 mm - 980 mm


Product specificaties

Merk: Sony
Categorie: Accessoires
Model: WS-X10FB

Heb je hulp nodig?

Als je hulp nodig hebt met Sony WS-X10FB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Accessoires Sony

Sony

Sony SU-RG11S Handleiding

21 December 2022
Sony

Sony SPK-SC100 Handleiding

20 December 2022
Sony

Sony MPK-THHB Handleiding

20 December 2022
Sony

Sony VPS-80DS Handleiding

17 December 2022
Sony

Sony NP-FX110 Handleiding

9 December 2022
Sony

Sony LCS-VCB Handleiding

5 December 2022
Sony

Sony PCK-LM14 Handleiding

3 December 2022
Sony

Sony MPK-HSR1 Handleiding

29 November 2022
Sony

Sony VAD-WB Handleiding

25 November 2022
Sony

Sony MPK-PEA Handleiding

22 November 2022

Handleiding Accessoires

Nieuwste handleidingen voor Accessoires