Sony RM-VD1 Handleiding

Sony Accessoires RM-VD1

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony RM-VD1 (2 pagina's) in de categorie Accessoires. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
3-080-853-12 (1)
Remote Commander
Télécommande
Operating Instructions
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Gebruiksaanwijzing
Bruksanvisning
Istruzioni per l’uso
Manual de instruções
И
нструкция по эксплуатации
English
For the customers in U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
CAUTION
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Features
• The RM-VD1 Remote Commander can be conencted to a Sony
video camera recorder equipped with a LANC terminal or a
Sony digital still camera equipped with an ACC terminal.
• This can be operated by attaching to the pan handle of the
tripod or to the shoulder belt using the clip (g) provided.
Notes
• Be sure not to drop the Remote Commander or spill liquid on
it.
• Do not leave the Remote Commander under direct sunlight,
near a heater, or in locations with high humidity.
• Store the Remote Commander in the supplied pouch after use.
• Arrange the Remote cord (e) using the supplied band.
• When turning off the POWER switch (a) of the Remote
Commander, wait a while before turning it on again. If you
operate the POWER switch (a) repeatedly,the unit connected to
the Remote Commander may not turn on properly.
• When inserting or pulling the Remote plug (f), be sure to do so
in a straight line. Performing this operation forcibly may
damage either the remote plug or the unit connected.
Identifying the parts (See Figure A)
aPOWER switch e Remote cord
bPHOTO button *1fRemote plug
cVIDEO button *2gClip
dZoom button
*1 This button functions as the PHOTO button when the Remote
Commander is used with a video camera recorder. It functions
as the shutter button when the Remote Commander is used
with a digital still camera.
*2 This button functions only when the Remote Commander is
used with a video camera recorder.
1Attaching the Remote Commander
1. Attach the Remote Commander to a certain object using the
clip (g) provided.
* When you use the Remote Commander attached to the
pan handle of the tripod, it is recommended that you hold
the Remote Commander in your hand to operate it as
shown in Figure B.
2. Be sure the video camera recorder/digital still camera to be
used is turned off before you insert the Remote plug (f) into
the LANC terminal or the ACC terminal. Be sure to do so
in a straight line.
2Setting the video camera recorder/digital still
camera to record images
Refer to the operating instructions of the unit used with the
Remote Commander for further information.
3Using the Remote Commander to record
When using a video camera recorder
Slide the POWER switch (a) along the arrow mark to turn on
the recorder.
The indicators of the PHOTO button (b) and the VIDEO button
(c) light in orange.
Recording moving images:
Press the VIDEO button (c) to start recording. The indicator of
the VIDEO button that lights in orange turns red. Press this
VIDEO button (c) again to stop recording and set the recorder
to standby mode. At this time, the indicator lights in orange
again.
Recording still images:
When you press the PHOTO button (b) all the way down, the
image is recorded.
*Refer to the operating instructions of the unit used with the
Remote Commander for further information.
*Some video camera recorders do not record still images.
When using a digital still camera
1. Slide the POWER switch (a) along the arrow mark to turn
on the recorder.
The indicator of the PHOTO button (b) lights in orange.
2. When you press the PHOTO button (b) all the way down,
the image is recorded.
*Refer to the operating instructions of the unit used with
the Remote Commander for further information.
3. Slide the POWER switch (a) along the arrow mark in Figure
B to turn off the camera.
Notes
• If an abnormality occurs, the indicator of the VIDEO button
(c) may flash. In this case, refer to the operating instructions
of the video camera recorder for further information.
• If you press and hold the PHOTO button (b) for a relatively
long time while using an external strobe, the strobe light may
not flash.
• Some video camera recorders models automatically start
from camera mode, which is one of the recorder’s functions,
when you turn the Remote Commander on. When you use
functions other than the camera mode, switch the mode
using the mode switch of the video camera recorder.
4Using the zoom feature
Press the Zoom button (d) of the Remote Commander halfway
down.
• T side (for telephoto): subject appears closer.
• W side (for wide-angle): subject appears farther away.
When you press the Zoom button (d) all the way down, some
video camera recorders/digital still cameras zoom more
quickly.
Specifications
Dimensions: Approx. 39 × 40 × 36 mm (1 9/16 × 1 5/8 ×
1 7/16 inches) (W/H/D)
(protruding portions not included)
Remote cord: Approx. 1.5 m (4.9 feet)
Mass: Approx. 44 g (1.6 oz)
Accessories: Pouch (1)/Band (1)/
Operating Instructions (1)
Design and specifications are subject to change without notice.
Refer to the operating instructions of the video camera recorder/
digital still camera for further information as well.
Français
Pour les clients au Canada
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Caractéristiques
La télécommande RM-VD1 peut être raccordée à un caméscope
Sony doté d’une borne LANC ou à un appareil photo
numérique Sony doté d’une borne ACC.
Ce raccordement peut être effectué en fixant la télécommande au
support universel du trépied ou à la bandoulière à l’aide de la
pince (g) fournie.
Remarques
Veillez à ne pas renverser de liquides sur la télécommande et à ne
pas la faire tomber.
Ne laissez pas la télécommande dans un endroit exposé aux
rayons directs du soleil, à un taux d’humidité élevé ou à côté d’un
chauffage.
Après utilisation, rangez le cordon de la télécommande dans
l’étui fourni à cet effet.
Installez la télécommande (e) à l’aide de la bande de fixation
fournie.
Après avoir mis le commutateur POWER (a) de la télécommande
en position d’arrêt, attendez un certain temps avant de le remettre
en position de marche. En cas d’activation répétée du
commutateur POWER (a), l’appareil raccordé à la télécommande
peut ne pas se mettre correctement sous tension.
Lors du branchement ou du débranchement de la fiche de la
télécommande (f), assurez-vous de bien pousser ou tirer
horizontalement. Si vous forcez pour brancher ou débrancher la
fiche, l’appareil raccordé ou la fiche elle-même peuvent être
endommagés.
Identification des pièces (voir Ill. A)
aCommutateur POWER e Cordon de la
bTouche PHOTO *1télécommand
cTouche VIDEO *2fPrise de télécommande
dTouche de zoom g Pince
*1 Cette touche fonctionne en tant que touche PHOTO lorsque la
télécommande est utilisée avec un caméscope. Cette touche
fonctionne en tant que touche d’obturateur lorsque la
télécommande est utilisée avec un appareil photo numérique.
*2 Cette touche fonctionne uniquement lorsque la télécommande
est utilisée avec un caméscope.
1Fixation de la télécommande
1. Fixez la télécommande sur un objet à l’aide de la pince (g)
fournie.
*Lors de l’utilisation de la télécommande fixée au support
universel du trépied, il est recommandé de tenir la
télécommande tel qu’indiqué dans l’illustration B.
2. Vérifiez bien que la caméscope ou l’appareil photo
numérique à utiliser est hors tension avant de brancher la
fiche de la télécommande (f) dans la borne LANC ou la
borne ACC. Veillez à bien pousser horizontalement sur la
fiche.
2Réglage du caméscope ou de l’appareil photo
numérique pour la prise de vue
Pour de plus amples informations, reportez-vous au mode
d’emploi de l’appareil utilisé avec la télécommande.
3Utilisation de la télécommande pour une prise
de vue
Lors de l’utilisation d’un caméscope
Faites coulisser le commutateur POWER (a) le long de la flèche
pour mettre le caméscope sous tension.
Les voyants de la touche PHOTO (b) et de la touche VIDEO (c)
s’allument en orange.
Prise de vue d’images animées :
Appuyez sur la touche VIDEO (c) pour lancer la prise de vue.
Le voyant de la touche vidéo, allumé en orange, devient rouge.
Appuyez de nouveau sur cette touche VIDEO (c) pour mettre
fin à la prise de vue et régler le caméscope en mode d’attente. A
ce moment, le voyant s’allume de nouveau en orange.
Prise de photos :
Lorsque vous appuyez à fond sur la touche PHOTO (b), la
photo est prise.
*Pour de plus amples informations, reportez-vous au mode
d’emploi de l’appareil utilisé avec la télécommande.
*Certains caméscopes ne permettent pas la prise de photos.
Lors de l’utilisation d’un appareil photo numérique
1. Faites coulisser le commutateur POWER (a) le long de la
flèche pour mettre le caméscope sous tension.
Le voyant de la touche PHOTO (b) s’allume en orange.
2Lorsque vous appuyez à fond sur la touche PHOTO (b), la
photo est prise.
* Pour de plus amples informations, reportez-vous au mode
d’emploi de l’appareil utilisé avec la télécommande.
3. Faites coulisser le commutateur POWER (a) dans le rail le
long de la flèche, tel qu’indiqué dans l’illustration B, pour
mettre l’appareil photo hors tension.
Remarques
• Si un phénomène anormal se produit, le voyant de la touche
VIDEO (c) peut se mettre à clignoter. Dans ce cas, reportez-
vous au mode d’emploi du caméscope pour obtenir de plus
amples informations.
Si vous maintenez la touche PHOTO (b) enfoncée pendant
longtemps alors qu’un stroboscope externe est utilisé, il est
possible que la lumière stroboscopique ne clignote pas.
Certains modèles de caméscopes démarrent
automatiquement à partir du mode d’appareil photo, qui est
une des fonctions du caméscope, lorsque vous mettez la
télécommande sous tension. Lors de l’utilisation de fonctions
autres que le mode d’appareil photo, commutez le mode à
l’aide du commutateur de mode du caméscope.
4Utilisation de la fonction de zoom
Enfoncez à moitié la touche de zoom (d) de la télécommande.
Côté T (pour le mode téléobjectif) : l’objet semble plus
rapproché.
Côté W (pour un grand-angle) : l’objet semble plus éloigné.
Lorsque vous appuyez à fond sur la touche de zoom (d),
certains caméscopes ou appareils photo numériques effectuent
un zoom plus rapide.
Spécifications
Dimensions : Environ 39 × 40 × 36 mm (L/H/P)
(partie saillante exclue)
Cordon de la télécommande :
Environ 1,5 m (4,9 pieds)
Poids : Environ 44 g (1,6 on)
Accessoires : Etui (1)/Sangle (1)/Mode d’emploi (1)
La conception et les spécifications sont sujettes à modification sans
préavis.
Pour de plus amples informations, reportez-vous également au
mode d’emploi du caméscope ou de l’appareil photo numérique.
Aufnehmen von Standbildern:
Wenn Sie die Taste PHOTO (b) ganz nach unten drücken, wird
das Bild aufgenommen.
*Weitere Informationen finden Sie in der
Bedienungsanleitung zu dem Gerät, das mit der
Fernbedienung verwendet wird.
*Mit einigen Videokameras lassen sich keine Standbilder
aufnehmen.
Bei einer digitalen Standbildkamera
1. Schieben Sie den Schalter POWER (a) entlang der
Pfeilmarkierung, um die Kamera einzuschalten.
Die Anzeige der Taste PHOTO (b) leuchtet orange.
2. Wenn Sie die Taste PHOTO (b) ganz nach unten drücken,
wird das Bild aufgenommen.
* Weitere Informationen finden Sie in der
Bedienungsanleitung zu dem Gerät, das mit der
Fernbedienung verwendet wird.
3. Schieben Sie den Schalter POWER (a) entlang der
Pfeilmarkierung in Abbildung B, um die Kamera
auszuschalten.
Hinweise
• Wenn Störungen auftreten, blinkt unter Umständen die
Anzeige der Taste VIDEO (c). Schlagen Sie in diesem Fall
weitere Informationen in der Bedienungsanleitung zur
Videokamera nach.
Wenn Sie ein externes Stroboskop verwenden und die Taste
PHOTO (b) relativ lange gedrückt halten, blinkt das
Stroboskop unter Umständen nicht.
Einige Videokameramodelle starten automatisch mit dem
Kameramodus, eine der Funktionen der Videokamera, wenn
Sie sie mit der Fernbedienung einschalten. Wenn Sie andere
Funktionen als den Kameramodus verwenden wollen,
wechseln Sie den Modus mit dem Modusschalter der
Videokamera.
4Der Zoom
Drücken Sie die Zoom-Taste (d) der Fernbedienung halb nach
unten.
• T-Seite (Telephoto): Das Motiv erscheint näher.
• W-Seite (Weitwinkel): Das Motiv erscheint weiter entfernt.
Wenn Sie die Zoom-Taste (d) ganz nach unten drücken, erfolgt
das Zoomen bei einigen Videokameras/digitalen
Standbildkameras schneller.
Technische Daten
Abmessungen: ca. 39 × 40 × 36 mm (B/H/T)
(ohne vorstehende Teile)
Fernbedienungskabel: ca. 1,5 m
Gewicht: ca. 44 g
Zubehör: Beutel (1)/Riemen (1)/
Bedienungsanleitung (1)
Änderungen, die dem technischen Fortschritt dienen, bleiben
vorbehalten.
Weitere Informationen finden Sie auch in der Bedienungsanleitung
zur Videokamera bzw. digitalen Standbildkamera.
Si mantiene pulsado el botón PHOTO (b) durante un período
relativamente largo y utiliza al mismo tiempo un flash
estroboscópico, es posible que éste no funcione.
Cuando encienda el mando a distancia, algunos modelos de
videocámara se inician automáticamente en el modo de
cámara, que es una de las funciones de la videocámara.
Cuando utilice funciones distintas del modo de cámara,
cambie de modo mediante el selector de modo de la misma.
4Utilización de la función de zoom
Pulse el botón del zoom (d) del mando a distancia hasta la
mitad.
• Lado T (para telefoto): el motivo aparece más cerca.
• Lado W (para gran angular): el motivo aparece más lejos.
Si pulsa totalmente el botón del zoom (d), algunos modelos de
videocámara o cámara digital de imágenes fijas realizarán el
zoom más rápidamente.
Especificaciones
Dimensiones: Aproximadamente 39 × 40 × 36 mm
(an/al/prf) (sin incluir partes salientes)
Cable remoto: Aproximadamente 1,5 m
Peso: Aproximadamente 44 g
Accesorios: Bolsa (1)/Banda (1)/
Manual de instrucciones (1)
El diseño y las especificaciones están sujetos a cambios sin previo
aviso.
Asimismo, consulte el manual de instrucciones de la videocámara o
de la cámara digital de imágenes fijas para obtener más
información.
Deutsch
Merkmale und Funktionen
Die Fernbedienung RM-VD1 können Sie an eine Videokamera
von Sony mit einem LANC-Anschluss oder an eine digitale
Standbildkamera von Sony mit einem ACC-Anschluss
anschließen.
Sie können die Fernbedienung mit der mitgelieferten Klammer (g)
am Schwenkarm des Stativs oder am Schulterriemen anbringen.
Hinweise
• Lassen Sie die Fernbedienung nicht fallen und verschütten Sie
keine Flüssigkeiten darauf.
Schützen Sie die Fernbedienung vor direktem Sonnenlicht und
lassen Sie sie nicht in der Nähe von Wärmequellen oder an Orten
mit hoher Luftfeuchtigkeit.
Bewahren Sie die Fernbedienung nach dem Gebrauch im
mitgelieferten Beutel auf.
Befestigen Sie das Fernbedienungskabel (e) mit dem
mitgelieferten Riemen.
• Wenn Sie mit dem Schalter POWER (a) an der Fernbedienung ein
Gerät ausschalten, warten Sie eine Weile, bevor Sie es wieder
einschalten. Wenn Sie den Schalter POWER (a) mehrmals
hintereinander betätigen, lässt sich das an die Fernbedienung
angeschlossene Gerät möglicherweise nicht richtig einschalten.
Der Fernbedienungsstecker (f) muss gerade eingesteckt und
herausgezogen werden. Wenn Sie den Stecker gewaltsam schräg
einstecken bzw. herausziehen, kann der Fernbedienungsstecker
oder das angeschlossene Gerät beschädigt werden.
Lage und Funktion der Teile und Bedienelemente
(siehe Abbildung A)
aSchalter POWER e Fernbedienungskabel
bTaste PHOTO *1fFernbedienungsstecker
cTaste VIDEO *2gKlammer
d Zoom-Taste
*1 Diese Taste fungiert als Taste PHOTO, wenn die Fernbedienung
mit einer Videokamera verwendet wird. Sie dient als Auslöser,
wenn die Fernbedienung mit einer digitalen Standbildkamera
verwendet wird.
*2 Diese Taste funktioniert nur, wenn die Fernbedienung mit einer
Videokamera verwendet wird.
1Anbringen der Fernbedienung
1. Bringen Sie die Fernbedienung mit der mitgelieferten
Klammer (g) an einem angegebenen Gegenstand an.
*Wenn Sie die Fernbedienung am Schwenkarm eines
Stativs anbingen, empfiehlt es sich, die Fernbedienung
beim Bedienen wie in Abbildung B dargestellt in der
Hand zu halten.
2. Schalten Sie die Videokamera/digitale Standbildkamera
unbedingt aus, bevor Sie den Fernbedienungsstecker (f) an
den LANC- bzw. ACC-Anschluss anschließen. Stecken
Sie den Fernbedienungsstecker unbedingt gerade in den
Anschluss.
2Einstellen der Videokamera/digitalen
Standbildkamera zum Aufnehmen von Bildern
Weitere Informationen finden Sie in der Bedienungsanleitung
zu dem Gerät, das mit der Fernbedienung verwendet wird.
3Starten der Aufnahme mit der Fernbedienung
Bei einer Videokamera
Schieben Sie den Schalter POWER (a) entlang der
Pfeilmarkierung, um die Kamera einzuschalten.
Die Anzeigen der Taste PHOTO (b) und der Taste VIDEO (c)
leuchten orange.
Aufnehmen von bewegten Bildern:
Starten Sie die Aufnahme mit der Taste VIDEO (c). Die Anzeige
der Taste VIDEO wechselt von orange zu rot. Wenn Sie die
Taste VIDEO (c) erneut drücken, wird die Aufnahme gestoppt
und die Kamera wechselt in den Bereitschaftsmodus. Nun
leuchtet die Anzeige wieder orange.
Español
Características
El mando a distancia RM-VD1 puede conectarse a una
videocámara Sony equipada con un terminal LANC o a una
cámara digital de imágenes fijas Sony equipada con un terminal
ACC.
Podrá utilizar este mando fijándolo al mango panorámico del
trípode o a la bandolera mediante la pinza (g) suministrada.
Notas
• Be sure not to drop the Remote Commander or spill No deje caer
el mando a distancia ni vierta líquidos encima del mismo.
• No exponga el mando a distancia a la luz solar directa. No lo
coloque cerca de fuentes de calor ni en lugares con mucha
humedad.
Guarde el mando a distancia en la bolsa suministrada después de
utilizarlo.
Recoja el cable remoto (e) mediante la banda suministrada.
Cuando apague el selector POWER (a) del mando a distancia,
espere unos segundos antes de volverlo a encender. Si utiliza
repetidamente el selector POWER (a), es posible que la unidad
conectada al mando no se encienda correctamente.
Cuando inserte o extraiga la clavija remota (f), asegúrese de
hacerlo en línea recta. Si lo hace de manera forzada, puede dañar
esta clavija o la unidad conectada.
Identificación de los componentes (consulte la figura A)
aSelector POWER e Cable remoto
bBotón PHOTO *1fClavija remota
cBotón VIDEO *2gPinza
dBotón de zoom
*1 Este botón hace las funciones del botón PHOTO cuando el
mando a distancia se utiliza con una videocámara, y las del
botón del obturador cuando el mando a distancia se utiliza con
una cámara digital de imágenes fijas.
*2 Este botón funcionará únicamente cuando el mando a distancia
se utilice con una videocámara.
1Fijación del mando a distancia
1. Fije el mando a distancia a un objeto mediante la pinza (g)
suministrada.
*Cuando utilice el mando a distancia fijado al mango
panorámico del trípode, se recomienda que sostenga el
primero con la mano para manejarlo, tal y como se
muestra en la figura B.
2. Compruebe que la videograbadora o la cámara de imágenes
fijas que va a utilizar esté apagada antes de conectar la
clavija remota (f) en el terminal LANC o en el terminal
ACC. Asimismo, inserte esta clavija en línea recta.
2Ajuste de la videocámara o la cámara digital de
imágenes fijas para grabar imágenes
Consulte el manual de instrucciones de la unidad que utilice
con el mando a distancia para obtener más información.
3Utilización del mando a distancia para grabar
Si utiliza una videocámara
Deslice el selector POWER (a) en la dirección que indica la
flecha para encender la videocámara.
Los indicadores de los botones PHOTO (b) y VIDEO (c) se
iluminarán en naranja.
Grabación de imágenes en movimiento:
Pulse el botón VIDEO (c) para iniciar la grabación. El indicador
del botón VIDEO que se iluminó en naranja cambiará a rojo.
Pulse de nuevo el botón VIDEO (c) para detener la grabación y
ponga la videocámara en modo de espera. Cuando lo haga, el
indicador se iluminará de nuevo en naranja.
Grabación de imágenes fijas:
Cuando pulse completamente el botón PHOTO (b), la imagen
se grabará.
*Consulte el manual de instrucciones de la unidad que utilice
con el mando a distancia para obtener más información.
*Algunas videocámaras no pueden grabar imágenes fijas.
Si utiliza una cámara digital de imágenes fijas
1. Deslice el selector POWER (a) en la dirección que indica la
flecha para encender la videocámara.
El indicador del botón PHOTO (b) se iluminará en naranja.
2. Cuando pulse completamente el botón PHOTO (b), la
imagen se grabará.
* Consulte el manual de instrucciones de la unidad que
utilice con el mando a distancia para obtener más
información.
3. Deslice el selector POWER (a) en la dirección que indica la
flecha de la figura B para apagar la cámara.
Notas
• Si se produce una situación anormal, es posible que el
indicador del botón VIDEO (c) parpadee. En tal caso,
consulte el manual de instrucciones de la videocámara para
obtener más información.
Nederlands
Kenmerken
De RM-VD1 afstandsbediening kan worden aangesloten op een
Sony videocamera met een LANC aansluiting of een Sony
digitale camera met een ACC aansluiting.
•U kunt de afstandsbediening bedienen door deze te bevestigen
aan de handgreep voor pannen op het statief of aan de
schouderband met de bijgeleverde clip (g).
Opmerkingen
• Laat de afstandsbediening niet vallen en mors geen vloeistof op
het apparaat.
Laat de afstandsbediening niet achter in direct zonlicht, in de
buurt van een verwarmingstoestel of op plaatsen met een hoge
vochtigheidsgraad.
Berg de afstandsbediening na gebruik op in de bijgeleverde
draagtas.
Pas het snoer van de afstandsbediening (e) aan met de
bijgeleverde riem.
• Als u de POWER schakelaar (a) van de afstandsbediening
uitschakelt, moet u enige tijd wachten voordat u deze weer
inschakelt. Bedient u de POWER schakelaar (a) herhaaldelijk, dan
wordt het apparaat dat is aangesloten op de afstandsbediening,
wellicht niet correct ingeschakeld.
Als u de aansluiting van de afstandsbediening (f) aansluit of
verwijdert, moet u dit in een rechte lijn doen. Als u deze
handeling met kracht verkeerd uitvoert, kan de aansluiting van
de afstandsbediening of het aangesloten apparaat worden
beschadigd.
Onderdelen (zie afbeelding A)
aPOWER schakelaar f Aansluiting van
bPHOTO knop *1afstandsbediening
cVIDEO knop *2gClip
dZoomknop
eSnoer van afstandsbediening
*1 Deze knop functioneert als PHOTO knop als de
afstandsbediening met een videocamera wordt gebruikt. De
knop functioneert als sluiterknop als de afstandsbediening met
een digitale camera wordt gebruikt.
*2 Deze knop functioneert alleen als de afstandsbediening met een
videocamera wordt gebruikt.
1De afstandsbediening bevestigen
1. Bevestig de afstandsbediening op een bepaald voorwerp
met de bijgeleverde clip (g).
*Als u de afstandsbediening gebruikt en deze aan de
handgreep voor pannen op het statief is bevestigd, kunt u
het beste de afstandsbediening in de hand houden om
deze te bedienen zoals afgebeeld in afbeelding B.
2. U moet de videocamera/digitale camera die u wilt
gebruiken, uitschakelen voordat u de aansluiting van de
afstandsbediening (f) in de LANC aansluiting of de ACC
aansluiting plaatst. Zorg dat u dit in een rechte lijn doet.
2De videocamera/digitale camera instellen om
beelden op te nemen
Raadpleeg de gebruiksaanwijzing van het apparaat dat met de
afstandsbediening wordt gebruikt voor meer informatie.
3Opnemen met de afstandsbediening
Met een videocamera
Schuif de POWER schakelaar (a) in de richting van de pijl om
de videocamera in te schakelen.
De lampjes van de PHOTO knop (b) en de VIDEO knop (c)
gaan oranje branden.
Bewegende beelden opnemen
Druk op de VIDEO knop (c) om de opname te starten. Het
lampje van de VIDEO knop verandert van oranje in rood. Druk
nogmaals op de VIDEO knop (c) om de opname te beëindigen
en de videocamera in de opnamepauzestand te zetten. Het
lampje wordt dan weer oranje.
Stilstaande beelden opnemen
Als u de PHOTO knop (b) volledig indrukt, wordt het beeld
opgenomen.
*Raadpleeg de gebruiksaanwijzing van het apparaat dat met
de afstandsbediening wordt gebruikt voor meer informatie.
*Bepaalde videocamera’s kunnen geen stilstaande beelden
opnemen.
Met een digitale camera
1. Schuif de POWER schakelaar (a) in de richting van de pijl
om de videocamera in te schakelen.
Het lampje van de PHOTO knop (b) gaat oranje branden.
2. Als u de PHOTO knop (b) volledig indrukt, wordt het beeld
opgenomen.
*Raadpleeg de gebruiksaanwijzing van het apparaat dat
met de afstandsbediening wordt gebruikt voor meer
informatie.
3. Schuif de POWER schakelaar (a) in de richting van de pijl in
afbeelding B om de camera uit te schakelen.
Opmerkingen
Als er een probleem optreedt, kan het lampje van de VIDEO
knop (c) gaan knipperen. In dit geval moet u de
gebruiksaanwijzing bij de videocamera raadplegen voor
meer informatie.
Als u de PHOTO knop (b) langere tijd ingedrukt houdt
terwijl u een extern flitslicht gebruikt, flitst het flitslicht
wellicht niet.
Als u de afstandsbediening inschakelt, worden bepaalde
videocamera’s automatisch gestart in de camerastand. Dit is
een van de functies van videocamera’s. Als u een andere
functie dan de camerastand gebruikt, moet u de stand
wijzigen met de schakelaar voor standen op de videocamera.
4De zoomfunctie gebruiken
Druk de zoomknop (d) van de afstandsbediening half in.
T-zijde (voor tele-opnamen): het onderwerp lijkt dichterbij.
W-zijde (voor groothoekopnamen): het onderwerp lijkt
verder weg.
Als u de zoomknop (d) volledig indrukt, zoomen bepaalde
videocamera's/digitale camera's sneller in of uit.
Svenska
Egenskaper
Fjärrkontrollen RM-VD1 kan anslutas till en Sony videokamera
med LANC-terminal eller en Sony digital stillbildskamera
med ACC-terminal.
Du kan manövrera fjärrkontrollen genom att fästa den på
kamerastativets panoreringshandtag eller på axelremmen med
hjälp av det medföljande clipet (g).
Obs!
Se till så att du inte tappar fjärrkontrollen eller spiller vätska på
den.
Lämna inte fjärrkontrollen i direkt solljus, nära ett
värmeelement eller på en plats där det är mycket fuktigt.
När du använt fjärrkontrollen förvarar du den i den
medföljande väskan.
Ordna och fäst kabeln till fjärrkontrollen (e) med det
medföljande bandet.
Om du stänger av strömmen till fjärrkontrollen med POWER-
omkopplaren (a) bör du vänta en stund innan du slår på
strömmen igen. Om du använder POWER-omkopplaren (a)
flera gånger efter varandra kan det hända att enheten som är
ansluten till fjärrkontrollen inte slås på som den ska.
• När du sätter i eller kopplar bort kontakten till fjärrkontrollen
(f) måste du se till att du håller den rakt. Om du använder våld
när du kopplar i eller ur kontakten kan antingen kontakten
eller den anslutna enheten skadas.
Identifiering av delar och kontroller (se fig. A)
aPOWER-omkopplare e Fjärrkontrollkabel
bPHOTO-knapp *1fFjärrkontrollkontakt
cVIDEO-knapp *2gClipet
dZoomningsknapp
*1 Den här knappen fungerar som PHOTO-knappen när
fjärrkontrollen används med en videokamera. Den fungerar
som slutarknapp när fjärrkontrollen används med en digital
stillbildskamera.
*2 Den här knappen fungerar bara när fjärrkontrollen används
med en videokamera.
1Fästa fjärrkontrollen
1. Fäst fjärrkontrollen på önskad plats med hjälp av det
medföljande clipet (g).
* När du använder fjärrkontrollen på kamerastativets
panoreringshandtag rekommenderas du att hålla
fjärrkontrollen i handen, som i fig B, när du använder
den.
2. Kontrollera att videokameran eller den digitala
stillbildskameran är avstängd innan du sätter i kontakten
för fjärrkontrollen (f) i LANC- eller ACC-terminalen.
Se till att du håller kontakten rakt när du kopplar i den.
2Ställa in videokameran/den digitala
stillbildskameran för att spela in bilder
Mer information finns i bruksanvisningen till den enhet som
du använder fjärrkontrollen för.
3Använda fjärrkontrollen för inspelning
När du använder en videokamera
Slå på strömmen till kameran genom att skjuta POWER-
omkopplaren (a) längs pilmarkeringen.
PHOTO-knappens (b) och VIDEO-knappens (c) indikatorer
lyser orange.
Spela in rörliga bilder:
Starta inspelningen genom att trycka på VIDEO-knappen (c).
VIDEO-knappens indikator, som lyser orange, växlar över
till rött. Tryck på den här VIDEO-knappen (c) igen när du
vill avbryta inspelningen och ställa inspelningen i
standbyläge. Nu lyser indikatorn orange igen.
Spela in stillbilder:
Bilden tas när du trycker in PHOTO-knappen (b) helt.
*Mer information finns i bruksanvisningen till den enhet
som du använder fjärrkontrollen för.
* Vissa videokameror kan inte spela in stillbilder.
När du använder en digital stillbildskamera
1. Slå på strömmen till kameran genom att skjuta POWER-
omkopplaren (a) längs pilmarkeringen.
PHOTO-knappens indikator (b) lyser orange.
2. Bilden tas när du trycker in PHOTO-knappen (b) helt.
*Mer information finns i bruksanvisningen till den
enhet som du använder fjärrkontrollen för.
3. Slå av strömmen till kameran genom att skjuta POWER-
omkopplaren (a) längs med pilmarkeringen i fig. B.
Obs!
Om någon funktionsstörning inträffar kan det hända att
VIDEO-knappens indikator (c) blinkar. I så fall finns mer
information i bruksanvisningen till videokameran.
• Om du trycker in PHOTO-knappen (b) under en längre tid
när du använder en extern blixt kan det hända att den inte
utlöses.
• När du slår på strömmen till fjärrkontrollen kan vissa
modeller av videokameror automatiskt starta i
kameraläget, som är en av videokamerans funktioner. Om
du då vill använda ett annat läge än kameraläget, växlar
du läge med videokamerans lägesomkopplare.
4Använda zoomningsfunktionen
Tryck ned zoomknappen (d) på fjärrkontrollen halvvägs.
T-sidan (för telefoto): motivet verkar ligga närmare.
W-sidan (för vidvinkelinspelning): motivet verkar mer
avlägset.
När du trycker in zoomningsknappen (d) helt zoomar vissa
videokameror/digitala stillbildskameror snabbare.
Tekniska data
Dimensioner: Ca. 39 × 40 × 36 mm (B/H/D)
(exklusive utstickande delar)
Fjärrkontrollkabel: Ca. 1,5 m
Vikt: Ca. 44 g
Tillbehör: Väska (1)/Band (1)/Bruksanvisning (1)
Utförande och specifikationer kan ändras utan föregående
meddelande.
Mer information finns även i bruksanvisningen till
videokameran/den digitala stillbildskameran.
Sony Corporation ©2003 Printed in Japan
RM-VD1
A
B
Printed on 70% or more recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
d
b
c
a
e
df g
Technische gegevens
Afmetingen: Ongeveer 39 × 40 × 36 mm (B/H/D)
(exclusief uitstekende onderdelen)
Snoer van afstandsbediening:
Ongeveer 1,5 m
Gewicht: Ongeveer 44 g
Accessoires: Draagtas (1)/Riem (1)/
Gebruiksaanwijzing (1)
Wijzigingen in ontwerp en technische gegevens voorbehouden
zonder voorafgaande kennisgeving.
Raadpleeg ook de gebruiksaanwijzing bij de videocamera/
digitale camera voor meer informatie.
A
B
4Uso della funzione zoom
Premere il tasto Zoom (d) del telecomando a metà.
• Lato T (per teleobiettivo): il soggetto appare più vicino.
• Lato W (per grandangolo): il soggetto appare più lontano.
Premendo completamente il tasto Zoom (d), alcune
videocamere/macchine fotografiche ferme digitali effettuano lo
zoom più rapidamente.
Caratteristiche tecniche
Dimensioni: Circa 39 × 40 × 36 mm (L/A/P)
(escluse le parti sporgenti)
Cavo del telecomando
:Circa 1,5 m
Peso: Circa 44 g
Accessori: Custodia (1)/Fermacavo (1)/
Istruzioni per l'uso (1)
Il design e le caratteristiche tecniche sono soggetti a modifiche
senza preavviso.
Per ulteriori informazioni, consultare inoltre le istruzioni per l'uso
della videocamera/macchina fotografica ferma digitale.
Português
Características
• O telecomando RM-VD1 pode ser ligado a um videogravador da
Sony equipado com um terminal LANC ou a uma máquina
fotográfica digital da Sony com um terminal ACC.
• Pode utilizar o telecomando ligando-o ao manípulo de deslocação
horizontal do tripé ou à correia a tiracolo, utilizando o clip (g)
fornecido.
Notas
Não deixe cair o telecomando nem o salpique com líquidos.
Não deixe o telecomando exposto à luz solar directa, perto de um
aquecedor ou em locais com muita humidade.
Depois de utilizar o telecomando, guarde-o na bolsa fornecida.
Enrole o cabo do telecomando (e) utilizando o suporte fornecido.
Quando desligar o interruptor POWER a) do telecomando,
aguarde um pouco antes de voltar a ligá-lo. Se utilizar várias
vezes o interruptor POWER (a),o aparelho ligado ao telecomando
pode não ligar correctamente.
• Quando introduzir ou retirar a ficha do telecomando (f), faça-o
em linha recta. Se forçar o movimento, pode danificar a ficha do
telecomando ou o aparelho ligado.
Identificação das peças (Consulte a Figura A)
aSelector POWER e Cabo do telecomando
bBotão PHOTO *1fFicha do telecomando
cBotão VIDEO *2gClip
dBotão de Zoom
*1 Este botão funciona como o botão PHOTO quando se utiliza o
telecomando com um videogravador. Funciona como o botão
do obturador quando se utiliza o telecomando com uma
máquina fotográfica digital.
*2 Este botão funciona apenas quando se utiliza o telecomando
com um videogravador.
1Prender o telecomando
1. Utilizando o clip (g) fornecido, pode prender o telecomando
a certos objectos.
*Quando utilizar o telecomando preso ao manípulo de
deslocação horizontal do tripé, recomendamos que o
agarre com a mão como mostra a Figura B.
2. Antes de introduzir a ficha do telecomando (f) no terminal
LANC ou terminal ACC, verifique se desligou o
videogravador / máquina fotográfica digital que vai
utilizar. Introduza a ficha a direito.
2Programar o videogravador/máquina
fotográfica digital para gravar imagens
Para obter mais informações, consulte o manual de instruções
do aparelho utilizado com o telecomando.
3Utilizar o telecomando para gravar
Se estiver a utilizar um videogravador
Para ligar o gravador, empurre o interruptor POWER (a) ao
longo da seta.
Os indicadores dos botões PHOTO (b) e VIDEO (c) acendem-se
em cor-de-laranja.
Gravar imagens em movimento:
Carregue no botão VIDEO (c) para começar a gravar. O
indicador do botão VIDEO passa de cor-de-laranja a vermelho.
Carregue novamente no botão VIDEO (c) para parar a gravação
e pôr o gravador no modo de espera. Nessa altura, o indicador
volta a ficar cor-de-laranja.
Gravar imagens fixas:
Se carregar até ao fim no botão PHOTO (b), a imagem fica
gravada.
*Para obter mais informações, consulte o manual de
instruções do aparelho utilizado com o telecomando.
*Alguns videogravadores não gravam imagens fixas.
Se estiver a utilizar uma máquina fotográfica digital
1. Para ligar o gravador, empurre o interruptor POWER (a) ao
longo da seta.
O indicador do botão PHOTO (b) acende-se em cor-de-
laranja.
2. Se carregar até ao fim no botão PHOTO (b), a imagem fica
gravada.
*Para obter mais informações, consulte o manual de
instruções do aparelho utilizado com o telecomando.
3. Para desligar a máquina, empurre o interruptor POWER (a)
ao longo da seta mostrada na Figura B.
Notas
Se houver alguma anomalia, o indicador do botão VIDEO (c)
pode piscar. Neste caso, consulte o manual de instruções do
videogravador para obter mais informações.
Se carregar sem soltar o botão PHOTO (b) durante algum
tempo, ao mesmo tempo que utiliza um strobe externo, a luz
do strobe pode não piscar.
Alguns modelos de videogravadores arrancam
automaticamente a partir do modo de câmara, que é uma das
funções do gravador, quando liga o telecomando. Se quiser
utilizar outras funções que não o modo de câmara, active o
modo com o interruptor de modo do videogravador.
4Utilizar a função de zoom
Carregue até meio no botão de Zoom (d) do telecomando.
• Lado T (teleobjectiva): o motivo aparece mais próximo.
• Lado W (grande angular): o motivo aparece mais longe.
Em alguns videogravadores/máquinas fotográficas digitais o
zoom é mais rápido se carregar no botão de Zoom (d) até ao
fim.
Especificações
Dimensões: Aprox. 39 × 40 × 36 mm (1 9/16 × 1 5/8 ×
1 7/16 polegadas) (L/A/P)
(excluindo peças salientes)
Cabo do telecomando: Aprox. 1,5 m (4,9 pés)
Peso: Aprox. 44 g, (1,6 onças)
Acessórios: Bolsa (1)/Suporte (1)/
Manual de instruções (1)
Design e especificações sujeitos a alterações sem aviso prévio.
Consulte também o manual de instruções do videogravador/
máquina fotográfica digital para obter mais informações.
Pyccкий
Italiano
Caratteristiche
Il telecomando RM-VD1 può essere collegato ad una
videocamera Sony dotata di un terminale LANC o ad una
macchina fotografica ferma digitale Sony dotata di un
terminale ACC.
•È possibile utilizzarlo collegandolo alla maniglia panoramica
del treppiede o alla cinghia da trasporto utilizzando l’apposito
fermaglio (g) in dotazione.
Note
Non lasciare cadere né bagnare il telecomando.
Non lasciare il telecomando alla luce solare diretta, in
prossimità di radiatori o in luoghi soggetti a umidità elevata.
Riporre il telecomando nell’apposita custodia in dotazione.
Avvolgere il cavo del telecomando (e) utilizzando il fermacavo
in dotazione.
Dopo avere disattivato l’interruttore POWER (a) del
telecomando, attendere alcuni istanti prima di riattivarlo. Se
l’interruttore POWER (a) viene utilizzato ripetutamente, è
possibile che l’apparecchio collegato al telecomando non si
accenda correttamente.
Durante l’inserimento o la rimozione della spina del
telecomando (f), assicurarsi di eseguire l’operazione tenendo la
spina in posizione orizzontale. Non eseguire tale operazione in
modo forzato, onde evitare di danneggiare la spina del
telecomando o l’apparecchio collegato.
Identificazione delle parti (vedere la figura A)
aInterruttore POWER e Cavo del telecomando
bTasto PHOTO *1fSpina del telecomando
cTasto VIDEO *2gL’apposito fermaglio
d Tasto Zoom
*1 Se il telecomando viene utilizzato con una videocamera,
questo tasto ha la stessa funzione del tasto PHOTO. Se il
telecomando viene utilizzato con una macchina fotografica
ferma digitale, questo tasto ha la stessa funzione del tasto
dell'otturatore.
*2 Questo tasto è disponibile solo se il telecomando viene
utilizzato con una videocamera.
1Collegamento del telecomando
1. Collegare il telecomando all'oggetto desiderato
utilizzando il fermaglio (g) in dotazione.
*Se il telecomando viene collegato alla maniglia
panoramica del treppiede, si consiglia di utilizzarlo
manualmente come mostrato nella figura B.
2. Prima di inserire la spina del telecomando (f) nel
terminale LANC o nel terminale ACC, assicurarsi che
la videocamera/macchina fotografica ferma digitale da
utilizzare sia spenta. Assicurarsi inoltre di eseguire
l’operazione tenendo la spina in posizione orizzontale.
2Impostazione della videocamera/macchina
fotografica ferma digitale per la registrazione
di immagini
Per ulteriori informazioni, consultare le istruzioni per l’uso
dell’apparecchio utilizzato con il telecomando.
3Uso del telecomando per la registrazione
Se viene utilizzata una videocamera
Per accendere la videocamera, fare scorrere l’interruttore
POWER (a) in direzione della freccia.
Gli indicatori dei tasti PHOTO (b) e VIDEO (c) si illuminano
in arancione.
Registrazione di immagini in movimento:
Premere il tasto VIDEO (c) per avviare la registrazione.
L'indicatore arancione del tasto VIDEO diventa rosso.
Premere di nuovo il tasto VIDEO (c) per arrestare la
registrazione e impostare la videocamera nel modo di attesa.
L'indicatore si illumina di nuovo in arancione.
Registrazione di fermi immagine:
L’immagine viene registrata quando il tasto PHOTO (b)
viene premuto completamente.
*Per ulteriori informazioni, consultare le istruzioni per l’uso
dell’apparecchio utilizzato con il telecomando.
*Alcune videocamere non sono in grado di registrare fermi
immagine.
Se viene utilizzata una macchina fotografica ferma digitale
1. er accendere la videocamera, fare scorrere l’interruttore
POWER (a) in direzione della freccia.
L'indicatore del tasto PHOTO (b) si illumina in arancione.
2. L’immagine viene registrata quando il tasto PHOTO (b)
viene premuto completamente.
*Per ulteriori informazioni, consultare le istruzioni per
l’uso dell’apparecchio utilizzato con il telecomando.
3. Per spegnere la macchina fotografica, fare scorrere
l'interruttore POWER (a) in direzione della freccia come
illustrato nella figura B.
Note
• In caso di problemi, è possibile che l’indicatore del tasto
VIDEO (c) lampeggi. Se ciò dovesse verificarsi, per
ulteriori informazioni, consultare le istruzioni per l'uso
della videocamera.
Tenendo premuto il tasto PHOTO (b) per un periodo di
tempo relativamente lungo durante l'uso di uno
stroboscopio esterno, è possibile che la spia dello
stroboscopio non lampeggi.
Al momento dell’attivazione del telecomando, alcuni
modelli di videocamera vengono automaticamente
impostati sul modo Camera, che costituisce una delle
funzioni della videocamera stessa. Per utilizzare funzioni
diverse dal modo Camera, è necessario cambiare il modo
utilizzando l’apposito interruttore della videocamera.
b
c
a
e
df g
Ocобeнноcти
Пyльт диcтaнционного yпpaвлeния RM-VD1 можно
подключить к видeокaмepe Sony, оcнaщeнной paзъeмом
LANC, или цифpовой фотокaмepe Sony, оcнaщeнной
paзъeмом ACC.
Eго можно иcпользовaть, пpикpeпив к pyкояткe штaтивa или
к плeчeвомy peмню c помощью пpилaгaeмого зaжимa (g).
Пpимeчaния
He pоняйтe пyльт диcтaнционного yпpaвлeния и нe
пpоливaйтe нa нeго никaкиx жидкоcтeй.
He оcтaвляйтe пyльт диcтaнционного yпpaвлeния в мecтax,
кyдa попaдaют пpямыe cолнeчныe лyчи, pядом c
обогpeвaтeлeм или в мecтax c повышeнной влaжноcтью.
Поcлe зaвepшeния иcпользовaния пyльтa диcтaнционного
yпpaвлeния eго cлeдyeт xpaнить в пpилaгaeмом чexлe.
Cвepнитe кaбeль пyльтa диcтaнционного yпpaвлeния (e),
иcпользyя пpилaгaeмyю тecьмy.
Поcлe выключeния выключaтeля питaния POWER (a) нa
пyльтe диcтaнционного yпpaвлeния подождитe нeкотоpоe
вpeмя, пpeждe чeм включaть eго cновa. Пpи чacтом
пepeключeнии выключaтeля POWER (a) ycтpойcтво, к
котоpомy подcоeдинeн пyльт диcтaнционного yпpaвлeния,
можeт нe включитьcя нaдлeжaщим обpaзом.
Пpи подключeнии или отключeнии штeкepa (f) кaбeля пyльтa
дepжитe eго пpямо. Heпpaвильноe выполнeниe этой
опepaции и пpиложeниe излишниx ycилий могyт пpивecти к
повpeждeнию штeкepa или подcоeдинeнного ycтpойcтвa.
Oбознaчeниe дeтaлeй (cм. pиc. A)
aBыключaтeль POWER
bКнопкa PHOTO *1
cКнопкa VIDEO *2
dКнопкa ZOOM
eКaбeль пyльтa диcтaнционного yпpaвлeния
fШтeкep диcтaнционного yпpaвлeния
gЗaжимa
*1 Этa кнопкa paботaeт кaк кнопкa PHOTO, когдa пyльт
диcтaнционного yпpaвлeния иcпользyeтcя вмecтe c
видeокaмepой. Oнa paботaeт кaк кнопкa зaтвоpa, когдa
пyльт диcтaнционного yпpaвлeния иcпользyeтcя вмecтe c
цифpовой фотокaмepой.
*2 Этa кнопкa paботaeт только в том cлyчae, когдa пyльт
диcтaнционного yпpaвлeния иcпользyeтcя вмecтe c
видeокaмepой.
1Пpиcоeдинeниe пyльтa диcтaнционного
yпpaвлeния
1. Пpикpeпитe пyльт диcтaнционного yпpaвлeния к
опpeдeлeнномy пpeдмeтy c помощью пpилaгaeмого
зaжимa (g).
*Пpи иcпользовaнии пyльтa диcтaнционного
yпpaвлeния, пpикpeплeнного к pyкояткe штaтивa,
peкомeндyeтcя дepжaть пyльт диcтaнционного
yпpaвлeния в pyкe, чтобы пользовaтьcя им, кaк
покaзaно нa pиc. B.
2. Пepeд подключeниeм штeкepa (f) к paзъeмy LANC
или paзъeмy ACC yбeдитecь, что видeокaмepa или
цифpовaя фотокaмepa, котоpyю тpeбyeтcя
иcпользовaть, включeнa. Дepжитe eго пpямо.
2Hacтpойкa видeокaмepы/цифpовой
фотокaмepы для зaпиcи изобpaжeний
Для полyчeния дополнитeльной инфоpмaции cм.
инcтpyкцию по экcплyaтaции aппapaтa, к котоpомy
подключeн пyльт диcтaнционного yпpaвлeния.
3Иcпользовaниe пyльтa диcтaнционного
yпpaвлeния для зaпиcи
Пpи иcпользовaнии видeокaмepы
Пepeдвиньтe пepeключaтeль POWER (a) по cтpeлкe,
чтобы включить кaмepy.
Индикaтоpы кнопок PHOTO (b) и VIDEO (c) зaгоpятcя
жeлтым cвeтом.
Зaпиcь движyщиxcя изобpaжeний:
Haжмитe кнопкy VIDEO (c), чтобы нaчaть зaпиcь.
Индикaтоp кнопки VIDEO вмecто жeлтого зaгоpитcя
кpacным cвeтом. Haжмитe кнопкy VIDEO (c) eщe paз,
чтобы оcтaновить зaпиcь и пepeвecти кaмepy в peжим
ожидaния. Ha этот paз индикaтоp cновa зaгоpитcя жeлтым
cвeтом.
Зaпиcь нeподвижныx изобpaжeний:
Ecли полноcтью нaжaть кнопкy PHOTO (b), нaчнeтcя
зaпиcь изобpaжeния.
*Для полyчeния дополнитeльной инфоpмaции cм.
инcтpyкцию по экcплyaтaции aппapaтa, к котоpомy
подключeн пyльт диcтaнционного yпpaвлeния.
*Heкотоpыe видeокaмepы нe зaпиcывaют нeподвижныe
изобpaжeния.
Пpи иcпользовaнии цифpовой фотокaмepы
1. Пepeдвиньтe пepeключaтeль POWER (a) по cтpeлкe,
чтобы включить кaмepy.
Индикaтоp кнопки PHOTO (b) зaгоpитcя жeлтым
cвeтом.
2. Ecли полноcтью нaжaть кнопкy PHOTO (b), нaчнeтcя
зaпиcь изобpaжeния.
*Для полyчeния дополнитeльной инфоpмaции cм.
инcтpyкцию по экcплyaтaции aппapaтa, к котоpомy
подключeн пyльт диcтaнционного yпpaвлeния.
3. Пepeдвиньтe пepeключaтeль POWER (a) по cтpeлкe
(кaк покaзaно нa pиc. B), чтобы выключить кaмepy.
Пpимeчaния
•B cлyчae возникновeния отклонeний индикaтоp кнопки
VIDEO (c) можeт мигaть. B этой cитyaции cм. инcтpyкцию
по экcплyaтaции видeокaмepы для полyчeния
дополнитeльной инфоpмaции.
Ecли нaжaть и yдepживaть кнопкy PHOTO (b) в тeчeниe
отноcитeльно пpодолжитeльного вpeмeни во вpeмя
иcпользовaния внeшнeго cтpобоcкопичecкого иcточникa
cвeтa, cтpобоcкопичecкий эффeкт вcпышки можeт нe
cpaбaтывaть.
Пpи включeнии пyльтa диcтaнционного yпpaвлeния
нeкотоpыe модeли видeокaмep aвтомaтичecки
зaпycкaютcя в peжимe кaмepы, котоpый являeтcя одной
из фyнкций видeокaмepы. Ecли нeобxодимо
иcпользовaть нe peжим кaмepы, a дpyгиe фyнкции,
пepeключитe peжим c помощью пepeключaтeля peжимa
нa видeокaмepe.
4Иcпользовaниe фyнкции тpaнcфокaции
Haжмитe нaполовинy кнопкy цифpовой тpaнcфокaции (d)
нa пyльтe диcтaнционного yпpaвлeния.
Cтоpонa T (тeлeфото): объeкт пpиближaeтcя.
Cтоpонa W (шиpокоyгольнaя cъeмкa): объeкт yдaляeтcя.
Ecли полноcтью нaжaть кнопкy цифpовой тpaнcфокaции
(d), нeкотоpыe видeокaмepы/цифpовыe фотокaмepы могyт
выполнять тpaнcфокaцию eщe быcтpee.
Texничecкиe xapaктepиcтики
Paзмepы: Пpибл. 39 × 40 × 36 мм (Ш/B/Г)
(выcтyпaющиe чacти нe включaютcя)
Кaбeль пyльтa диcтaнционного yпpaвлeния:
Пpибл. 1,5 м
Macca: Пpибл. 44 г
Дополнитeльныe пpинaдлeжноcти:
Фyтляp (1)/Tecьмa (1)/
Инcтpyкция по экcплyaтaции (1)
Конcтpyкция и тexничecкиe xapaктepиcтики могyт измeнятьcя
бeз пpeдвapитeльного yвeдомлeния.
Дополнитeльнyю инфоpмaцию cм. тaкжe в инcтpyкции по
экcплyaтaции видeокaмepы/цифpовой фотокaмepы.


Product specificaties

Merk: Sony
Categorie: Accessoires
Model: RM-VD1

Heb je hulp nodig?

Als je hulp nodig hebt met Sony RM-VD1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Accessoires Sony

Sony

Sony SU-RG11S Handleiding

21 December 2022
Sony

Sony SPK-SC100 Handleiding

20 December 2022
Sony

Sony MPK-THHB Handleiding

20 December 2022
Sony

Sony VPS-80DS Handleiding

17 December 2022
Sony

Sony NP-FX110 Handleiding

9 December 2022
Sony

Sony LCS-VCB Handleiding

5 December 2022
Sony

Sony PCK-LM14 Handleiding

3 December 2022
Sony

Sony MPK-HSR1 Handleiding

29 November 2022
Sony

Sony VAD-WB Handleiding

25 November 2022
Sony

Sony MPK-PEA Handleiding

22 November 2022

Handleiding Accessoires

Nieuwste handleidingen voor Accessoires