Sony alpha 200 Handleiding

Sony Digitale camera alpha 200

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony alpha 200 (109 pagina's) in de categorie Digitale camera. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/109
Revision History
Revision History
Sony EMCS Co.
DSLR-A200_L2
SERVICE MANUAL
LEVEL 2
Link
DISASSEMBLY
SERVICE NOTE
SPECIFICATIONS
SCHEMATIC DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
BLOCK DIAGRAMS
REPAIR PARTS LIST
PRINTED WIRING BOARDS
Link
Ver. 1.0 2007.12
2007L0500-1
© 2007.12
Published by Kohda TEC9-852-244-31
AEP Model
UK Model
Chinese Model
Japanese Model
DIGITAL SINGLE LENS REFLEX CAMERA
DSLR-A200
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
— 2 —
DSLR-A200_L2
SPECIFICATIONS
Camera
[System]
Camera TypeDigital Single Lens Reflex
Camera with built-in flash
and interchangeable lenses
Lens All of α Lens
[Image sensor]
Total pixel number of camera
Approx. 10 800 000 pixels
Effective pixel number of camera
Approx. 10 200 000 pixels
Image format23.6 × 15.8mm (APS-C
format) Interlace scan
Primary Color
ISO sensitivity (Recommended
exposure index)
AUTO, 100 to 3200
[Super SteadyShot]
System Image sensor-Shift
mechanism
Super SteadyShot Compensation
capability
Approximately 2.5 to 3.5
EV decrease in shutter
speed (varies according to
shooting conditions and
lens used)
[Anti-Dust]
System Charge protection coating
on Low-Pass Filter and
image sensor-Shift
mechanism
[Viewfinder]
Type Fixed eye-level,
penta-Dach-mirror
Focusing Screen
Spherical Acute Matte
Field of View
0.95
Magnification
0.83 × with 50 mm lens at
infinity, –1 m–1
Eye Relief Approximately 17.6 mm
from the eyepiece,
13.5 mm from the eyepiece
frame at –1 diopter
(–1 m–1)
Dioptor Adjustment
–2.5 to +1.0 m–1
[Auto Focus System]
System TTL phase-detection
system, CCD line sensors
(9 points, 8 lines with
center cross-hair sensor)
Sensitivity Range
0 to 18 EV (at ISO 100
equivalent)
AF illuminator
Approx. 1 to 5 m (3.3 to
16 feet)
[Exposure]
Metering Cell
40-segment honeycomb-
pattern SPC
Metering Range
1 to 20 EV (3 to 20 EV
with Spot metering), (at
ISO 100 with F1.4 lens)
Exposure compensation
±2.0 EV (1/3 EV step)
[Shutter]
Type Electronically-controlled,
vertical-traverse, focal-
plane type
Speed range 1/4000 second to 30
seconds, bulb, (1/3 EV
step)
Flash sync speed
1/160 second
[Built-In-Flash]
Flash G.No. GN 12 (in meters at ISO
100)
Recycling time
Approx. 4 seconds
Flash coverage
Covering 18 mm lens
(focal length that the lens
indicates)
Flash compensation
±2.0 EV (1/3 EV step)
[Recording media]
CompactFlash card
(TypeI,II), Microdrive,
“Memory Stick Duo”
(With a Memory Stick Duo
Adaptor for CompactFlash
slot)
[LCD monitor]
LCD panel 6.7 cm (2.7 type) TFT
drive
Total number of dots
230 400 (960 × 240) dots
[Power, general]
Used battery pack
Rechargeable battery pack
NP-FM500H
[Others]
PictBridge Compatible
Exif Print Compatible
PRINT Image Matching III
Compatible
Dimensions Approx. 130.8 × 98.5 ×
71.3 mm (5 1/4 × 4 ×
2 7/8 inches) (W/H/D,
excluding protrusions)
Mass Approx.532 g (1 lb 2.8 oz)
(without batteries, memory
card and body accessories)
Operating temperature
0 to 40°C (32 to 104°F)
(When using the
Microdrive: 5 to 40°C (41
to 104°F))
Exif Exif Ver.2.21
USB communication
Hi-Speed USB (USB 2.0
compliant)
BC-VM10 Battery charger
Input rating 100 V – 240 V AC, 50/60
Hz
Output rating 8.4 V DC, 750 mA
Operating temperature range
0 to 40°C (32 to 104°F)
Storage temperature range
–20 to +60°C (–4 to
+140°F)
Maximum dimensions
Approx. 70 × 25 × 95 mm
(2 7/8 × 1 × 3 3/4 inches)
(W/H/D)
Mass Approx. 90 g (3.2 oz)
Rechargeable battery pack
NP-FM500H
Used batteryLithium-ion battery
Maximum voltage
DC 8.4 V
Nominal voltage
DC 7.2 V
Maximum charge current
2.0 A
Maximum charge voltage
DC 8.4 V
Capacity 11.8 Wh (1 650 mAh)
Maximum dimensions
Approx. 38.2 × 20.5 × 55.6
mm (1 9/16 × 13/16 × 2 1/4
inches) (W/H/D)
Mass Approx. 78 g (2.8 oz)
Design and specifications are subject
to change without notice.
1-1
ENGLISH JAPANESE
ENGLISH JAPANESE
DSLR-A200_L2
1. SERVICE NOTE
1-1. CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
•Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
•Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
•Keep containers sealed to avoid natural evaporation when chemicals are not in use.
•Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and
use up it.
1-2. EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning plastic parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
•Insert the specific screws vertically to the part when installing a plastic part.
Be careful not to tighten screws too much.
1-3. UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
•Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenomenon.
1-4. SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 °C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

Product specificaties

Merk: Sony
Categorie: Digitale camera
Model: alpha 200

Heb je hulp nodig?

Als je hulp nodig hebt met Sony alpha 200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Digitale camera Sony

Sony

Sony alpha 200 Handleiding

23 December 2022
Sony

Sony DSC-W7S Handleiding

8 Mei 2022
Sony

Sony DSC-W120L Handleiding

3 Mei 2022
Sony

Sony DSC-T33 Handleiding

25 April 2022
Sony

Sony Cyber-SHOT DSC-W70 Handleiding

4 Maart 2022
Sony

Sony Cyber-SHOT DSC-P52 Handleiding

24 Februari 2022
Sony

Sony DSC-RX10M2 Cyber-shot Handleiding

25 April 2022
Sony

Sony DSC-H5B Handleiding

16 April 2022
Sony

Sony cyber shot dsc w215 Handleiding

26 Februari 2022
Sony

Sony DSLR-A100W Handleiding

13 Mei 2022

Handleiding Digitale camera

Nieuwste handleidingen voor Digitale camera

Oregon Scientific

Oregon Scientific atc 2 k Handleiding

16 Oktober 2023
Oregon Scientific

Oregon Scientific ATC3K Action Camera Handleiding

16 Oktober 2023
Oregon Scientific

Oregon Scientific atc 3000 atc3k action kamera Handleiding

16 Oktober 2023
Oregon Scientific

Oregon Scientific atc 2000 action kamera Handleiding

16 Oktober 2023
Oregon Scientific

Oregon Scientific ATCMini action camera Handleiding

16 Oktober 2023
Oregon Scientific

Oregon Scientific ATC-2000 Handleiding

16 Oktober 2023
General Electric

General Electric A1030 Handleiding

14 Oktober 2023
General Electric

General Electric E1030 Handleiding

14 Oktober 2023
General Electric

General Electric E1040 Handleiding

14 Oktober 2023
General Electric

General Electric E1050 Handleiding

14 Oktober 2023