Sonicsmith ConVertor E1 Handleiding

Sonicsmith Niet gecategoriseerd ConVertor E1

Lees hieronder de đź“– handleiding in het Nederlandse voor Sonicsmith ConVertor E1 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 124 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
PITCH FM IN
GATE
SYNTH
A-GAIN
ENV GATE
PRE OUT
ENV
TRS
AUDIO IN
+4-10-20-30-40-50
HI Z
FLT
P SHIFT
C Q
+-
+-
1) Connecting & powering
User Guide Firmware 0.9
To use the ConVertor E1 you need a -12/12V powered Eurorack case with 6HP
(3cm) available space, one available power connection and 150mA of current
available. Connect the power header cable, screw the panel to the rack using at
least two standard M3 screws. Avoid exposing it to sun, fluids or unchecked
physical abuse/shocks.
It’s recommended to avoid patching any audio signal stronger than +4dBu or
CV signals into the audio input. The audio & CV outputs of this device are
very loud, potentially around 10V scale so always test a signal’s loudness before
patching it with speakers or headphones on by dimming any speakers first.
Thank you for pre-ordering the ConVertor E1.
The ConVertor will convert an analog monophonic audio signal
into its Pitch, ENV and GATE Control Voltage, DC signals to control
external analog synths. It also provides its own internal digital
synth that is always in perfect tune to the incoming audio’s pitch.
It can work by itself with external synths or soon will have an
option to expand to a full synth voice on its own right, via Firm 2.x
series (available soon). You can also expand it via a MIDVertor E1
adding sustain pedal, MIDI i/o, arpeggiation and mainframe for up
to 7 additional ConVertors in parallel.
Feel free to write us with any feedback, question or concern at:
info@sonicsmith.com
Oct. 2021
PITCH FM IN
GATE
SYNTH
ENV GATE
P SHIFT
+-
+-
3) Knobs assignments: default
Turn the P SHIFT knob to increase/decrease the pitch shiî ‡
of the internal DCO as well as the CV PITCH output across -2-+2
octaves. Press the P SHIFT knob to bypass the shiî ‡ back to
unison Press it again to undo/redo..
Turn the GATE knob to increase/decrease the gate’s threshold by +/- 1dB.
Default GATE threshold is -35 dBFS and will effect the ENV CV output by
shutting the ENV CV to 0V as well as the SYNTH OUT audio off. Connect pre out
using a minijack TS to a +18dBu capable destination like modular synths.
A u d i o C o n t r o l l e d S y n t h e s i z e r
PIT CH FM I N
GAT E
SYN T H
A-G AIN
ENV GATE
PRE OUT
ENV
T RS
AUD IO I N
+4-10-20-30-40-50
HI Z
FLT
P S HIFT
C Q
+-
+-
A u di o C o n t r o ll ed S yn t h e s i z er
2) Preamp section
Connect a TS or TRS Mic/Inst./Line 1/4” plug into the audio input
If you play a pickup inst. press the
HI Z
to toggle between
analog input HPF frequencies:
Press A-GAIN to activate Auto-GAIN detection. Play loudly
once or twice, and aî ‡er 2.5 seconds, the gain will be set and the
meter will go back to showing input levels. The gate will not
effect the PRE OUT levels. To change the gain manually,
push the GATE knob and adjust the gain with the encoder. If you
don’t touch the knob again for 1.5 seconds, it will change back
to controlling the gate threshold.
The PRE OUT is a copy of the same signal going in to the ADC.
Press FLT
LOW Z: 50 kOhm
20 Hz 80 Hz
GREEN
GREEN RED
160 Hz
HI Z: 2000 kOhm
A-GAIN
PRE OUT
TRS
AUDIO IN
+4-10-20-30-40-50
HI Z
FLT
Mic/Inst/line input
Synth out
FM CV in Pitch CV
ENV CV
GATE CV
Preamp out
“Sonicsmith bus” 4 pin header
to other E1 devices (optional)
Balanced/unbalanced
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
4) SYNTH & compression 5) Quantizing FM CV input
SYNTH
Press the SYNTH button to toggle between the 4 waveforms:
GRNOff Red Red
ENV
+
Press the buttons to engage a 3:1 ENV + A-Gain
compression effect on the internal VCA CV and ENV CV output.
Press them again to bypass the compression.
Find the latest firmware on:
https://sonicsmith.com/products/convertor-e1/
Download it into a micro SD card and insert it into the back of
the ConVertor E1. Power the ConVertor off, then press &
hold the HI Z + FLT buttons while powering up the unit.
Keep holding the buttons for 2.5 seconds. While flashing, the
meter LED’s to the right will blink one aer another showing
the two micro-controllers that are flashing.
Join our newsletter on our home page or write us at
info@sonicsmith.com
No sound from SYNTH out: Do you see the audio meter go higher
than the first 3 LED’s? If not, turn up the gain and make sure the GATE LED turns off
when sound supposed to play. Try decreasing the GATE with the lower knob.
Press A-GAIN to get enough gain. Check where the SYNTH out is routed to.
Noisy output: Make sure the gate is high enough to allow only intentional
notes through. Plug the PRE OUT and listen to the original audio you are playing
into the ConVertor. Make sure it has a clear pitch and no excessive noises. Try
restarting the units and make sure it has at least 150 mA to itself. Try restarting the
units from external switch or case plug.
Weird behavior: Make sure your power supply can allocate at least 150mA
to the ConVertor. Powering up the unit by simply connecting the power ribbon
cable is not recommended. Try restarting your unit from a main switch or even
disconnecting the glug to from the case. Also try minimizing the use of HI Z with
high gains. The gain can climb higher than a pickup normally needs.
Contact: info@sonicsmith.com for any questions about the product.
6) Troubleshooting 7) Flashing / updating firmware
Press the button to toggle FM input quantizer (light on) Q
This will quantize the FM input to semitone shiî ‡s from the funda-
mental pitch. Semitone quantization helps with external arppe-
giation from external CV sources like LFO’s and sequencers.
Press it again to turn off the FM input quantizer as
continuous mode (LED off).
C Q
C Q
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
ConVertor E1 User Guide - Firmware 0.9 Oct. 2021
HI Z
FLT

Product specificaties

Merk: Sonicsmith
Categorie: Niet gecategoriseerd
Model: ConVertor E1

Heb je hulp nodig?

Als je hulp nodig hebt met Sonicsmith ConVertor E1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Sonicsmith

Sonicsmith

Sonicsmith ConVertor E1 Handleiding

27 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024