Sonance SBXL-100 Handleiding

Bekijk gratis de handleiding van Sonance SBXL-100 (2 pagina’s), behorend tot de categorie Soundbar. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.0 sterren uit 7 reviews. Heb je een vraag over Sonance SBXL-100 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

SBXL-100 SOUNDBAR

QUICKSTART GUIDE

BOX CONTENTS

• SBXL-100 Soundbar Quickstart Guide

• UA Series 2-125 Amplifier Quickstart Guide

• Sonance SBXL-100 Soundbar

• Power Cord

• 1/32”, 1/16”, 1/8”, and 1/4” Shims

• Straight Edge Alignment Template with Level

• Two (2) Z-Brackets

• Ten (10) Mounting Screws

BEFORE YOU BEGIN

IMPORTANT, TEAM LIFT REQUIRED:Two or more

people must assist with installation. Never release the

soundbaruntil you confirm it is securely mounted.

Always have multiple peopleholding the bar when

removing it from the wall.

IMPORTANT, SAFE MOUNTING: The SBXL-100

Z-brackets are designed for 16” on-center stud

construction with adjustable positioning for 11” to 24”

spacing between studs. Each bracket must be secured

to two or more studs for safe installation.

IMPORTANT, ELECTRICAL REQUIREMENTS: The SBXL-

100 requires connection to a power outlet. Sonance

doesnot recommendrunning high-voltage power cords

through walls. Plan ahead. Have an electrician install an

outlet behind the SBXL-100 Soundbar to provide power

before beginning installation.

CAUTION: The SBXL-100 grille features multiple strong

magnets. Use caution when attaching or removing the

grille from the soundbar.

Figure 1: Relative Position of the Alignment Template

to the Back of the SBXL-100 Soundbar

Alignment Template

SBXL-100 Soundbar Back View

Level the template until

the bubble is centered

Wall Z-Bracket Mounting Range

Soundbar-Mounted

Z-Bracket

HDMI Knockout

Power Cord Knockout

Soundbar-Mounted

Z-Bracket

Wall Z-Bracket Mounting Range

Figure 2: Alignment Template Zones

1. Carefully remove the grille from the soundbar and

set aside. The grille contains strong magnets. Keep

fingers clear when separating to avoid pinching.

2. Hold the Alignment Template against the wall in

the desired position of the SBXL-100 Soundbar,

aligning the top of the template with the desired

height of the soundbar. Be sure it is oriented with

the two Z-Bracket markings facing downward so

they appear on the bottom edge of the Alignment

Template (see Figure 2).

NOTE: When mounting below a TV that is already

mounted, allow at least 2” (50mm) above the top of

the Alignment Template to provide enough clearance

to lower the SBXL-100 Soundbar onto its Z-Bracket.

3. Adjust the Alignment Template’s positioning until

the the bubble in the level is centered, indicating the

template is level on the wall (see Figure 2).

4. Use two provided screws to secure the Alignment

Template to the wall anywhere on its surface.

5. Use a stud finder to locate studs along the width of

the Alignment Template and mark their locations

along the bottom edge.

6. Refer to Figure 2. Note the bottom edge of the

template with the two outlined Z-bracket areas.

The bottom edge of the template will meet the top

edge of the Z-Brackets. The Z-Brackets will need to

be mounted within the two dotted areas below the

template as marked in Figure 2.

7. Identify the two knockout locations to the left and

right of the bubble level on the Alignment Template

(see Figure 2). Mark the size and locations for these

two areas on the wall along the bottom of the

Alignment Template. This will help identify where to

cut the surface for wiring low voltage connections

(the left portion), and placement for an electrician

to install an outlet for power (the right portion).

8. Place one Z-bracket along the bottom edge of

the Alignment Template with the screw hole edge

facing downward and flat against the wall. The top

portion of the bracket will hover o the wall.

9. Move the Z-bracket into position along the bottom

edge of the Alignment Template, in line with the left

rectangular outline. Make sure that the top edge

of the bracket touches the bottom edge of the

Alignment Template, but do not overlap.

10. Move the bracket left or right as needed to align

the mounting holes with the stud locations. It is

okay if the bracket does not perfectly match the left

and right boundaries of the left rectangular outline

markings, but it should not extend outside of the

physical boundary width of the Alignment Template.

NOTE: The SBXL-100 Soundbar features

in-app setting adjustments for its built-in

Sonance UA Series amplifier (see the full

manual for details). Scan the QR Code to

get the app.

INSTALLATION

The alignment template ensures level Z-bracket

mounting. Its top edge represents the final soundbar

position (see Figure 1).

Product specificaties