Smartwares VD27 Handleiding

Smartwares Intercomsysteem VD27

Lees hieronder de 📖 handleiding in het Nederlandse voor Smartwares VD27 (14 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14

Package & Accessories

Included Quantity Mark Remark

Indoor Monitor 1 A Indoor monitor with LCD screen

Screw 4 B Two pairs depending on thickness

of the door

Outdoor Camera 1 C The ribbon cable will go through

Peephole to connect Indoor Part

Steel Bracket 1 D Use scre racket w to ﬁx the steel b

with Outdoor part

User Manual 1

Door

D. Steel Bracket

A. Indoor monitor

B. Fixing screws

Ribbon cable

Drill Hole in door

C. Outdoor camera

13-20mm 3x

Smart Peephole Viewer/

Visual Doorbell User Manual

You will need

Either remove your current door viewer or drill a new hole at least

13mm diameter up to 20mm diameter Into your door in a suitable position

to view the visitor.

N.B. Always test the product before installation.

Open the battery cover of the indoor monitor (A) and insert the Micro SD card.

Then insert 3x AA batteries making sure they are inserted correctly.

N.B. Please install the Micro-SD card before inserting the batteries.

Taking extra care with the ribbon cable gently push the indoor monitor

(A) back onto the steel bracket (D) and slide down to lock into position.

Insert your selected screws (B) according to your door thickness into

the Outdoor camera (C) but do not fully tighten.

Push the door viewer (C) into position making sure the ribbon cable

is pushed through first and the up arrow on the back of the camera

is facing up.

Connect the ribbon cable by pushing it onto the connection, you will feel

a “Click” as it locks onto the circuit board. Make sure the cable is fitted

the correct way around as shown in the image.

Using the steel bracket (D), make sure the up arrow is facing up and

push the ribbon Cable through the slot. Then allow the screws to push

through the holes so the steel bracket becomes flush with the door.

Tighten the screws to fix the steel bracket and Outdoor camera

into position.

Clip the battery cover back on, the ribbon cable will fit in a small opening

allowing it to come through the cover.

01 04

1 2 3

02 05

03 06

Technical Specifications

Conforms to all relevant European Directives.

Recycling

This symbol is known as the ‘Crossed-out Wheelie Bin Symbol’.

When this symbol is marked on a product or battery, it means that

it should not be disposed of with your general household waste.

Some chemicals contained within electrical/electronic products or

batteries can be harmful to health and the environment. Only dispose

of electrical/electronic/battery items in separate collection schemes,

which cater for the recovery and recycling of materials contained within.

Your co-operation is vital to ensure the success of these schemes and

for the protection of the environment

Indoor-part Dimension: 136×75×18mm

Outdoor-part Dimension: 30×30×7mm

Door hole range: 13mm~20mm

Door thickness range: 35mm~105mm

Battery: 3x AA batteries (Not included）

Battery life: 3 months (based on 10 operations per day)

Voltage: 4.5V~3.5V

Notes

We recommend that good quality, branded, alkaline batteries

are used.

Do not leave the product on uneven or unstable surfaces to prevent

damage caused by falling.

Try to avoid placing the product on high-temperature surfaces,

high humidity or a lot of dust, salt spray and other harsh environments

as this may reduce the lifespan of the product.

Take care with the ribbon cable on the door viewer to avoid damage.

Smartwares declares that the appliance, model [VD27], complies

with the main essential requirements of the R&TTE directive,

1999/5/CE. The complete declaration of conformity is available

on request at:

In more detail...

Installation

Time Date

Visitor Records

System Setting User Guide

Battery Indication Enter key

Right Key

Left Key

Smart Peephole Viewer/

Visual Doorbell User Manual

How to use

System Features

User Guide & Trouble Shooting

Safety Information

Main operation:

In order to operate the unit to view a visitor press the

Answer key (1) and the screen will display the camera

image. After 10 seconds of no activity the screen will

turn off. Should you want to record an image or video

of the visitor press the Answer key (1) to display the

camera and the Answer key (1) again to begin recording.

Menu settings:

For all menu options use the LEFT (2) & Right (3) keys

to scroll through the options and use the Menu/OK key

(4) to select any option. To exit the menus press the Answer

Key (1). Press the Menu/OK key (4) to enter the menu

screen (opposite):

View images / recordings:

Press the Menu/OK key (4) to enter recording menu. The date of recording will be displayed and press the Menu/OK key

(4) to enter the day and a list of stored images / recordings. Use the left (2) and right (3) keys to scroll through the list and

press the Menu/OK key (4) to display the image / recording.

To delete an image / recording:

Press the Menu/OK key (4) to enter recording menu. The date of recording will be displayed and press the Menu/OK

key (4) to enter the day and a list of stored images / recordings. Use the left (2) and right (3) keys to scroll through the

list and HOLD the Menu/OK key for 5 seconds and “Delete” will appear, press the Menu/OK button again to delete.

System settings:

Press the Right key (3) to highlight system setting and press the Menu/OK key (4). Use the Left (2) right (3) keys to scroll

through the menu using the Menu/OK key (4) to enter each section:

• Date & Time – Adjust the date and time that will show on images and recordings

• Language - Adjust the language of the device

• Recording mode – Select between images or recordings of the visitor

• LCD Brightness - Adjust the screen brightness (higher uses more battery power)

• Video Recording Time – Adjust the amount of time to record the visitor 3, 5 or 10 seconds

• Backlight time - Adjust how long to keep the screen on for 5, 10, 15 or 20 seconds

• Format Micro SD Card – Erase all data from the Micro SD Card

• Restore Factory settings - Restore the device to factory settings

IMPORTANT — RETAIN THIS INFOMATION R FO FUT E R REUR EFE NCE — READ CAR EFULLY

User Guide:

Press the Right key (3) to highlight User Guide and press the Menu/OK key (4) to Show the system information.

Troubleshooting:

Q. My unit does not power up / show anything on the screen when I press the buttons

A. Please check the batteries, make sure they are good quality and are inserted correctly.

Q. My unit randomly powers on/off

A. Please replace the batteries

Q. Unit displays “Insert Memory Card” when trying to take an image or recording

A. Make sure the Micro SD Card is inserted correctly, remove the batteries, remove and re insert the Micro SD

card and re insert the batteries

Q. Unit displays “Camera Module not Ready”

A. Make sure the ribbon cable is connected correctly to the Indoor monitor (See step 5 installation)

The ventilation should not be impeded by covering the

ventilation openings with items, such as newspapers,

tablecloths, curtains, etc...

DO NOT allow this product to come into direct contact

with heat or a naked flame.

The normal operation of the product may be disturbed

by strong electromagnetic interference.

This equipment is intended for domestic use only.

The appliance shall not be exposed to dripping or splashing.

No objects filled with liquids, such as vases, shall be

placed on the appliance.

Keep a minimum distance of 10 cm around the product

for sufficient ventilation.

Ensure the bell push is not mounted where it could become

immersed by water/rain.

DO NOT allow children to play with this appliance.

An adult must carry out battery replacement and installation.

Remove exhausted batteries from this product.

DO NOT dispose of batteries in a fire, batteries may

explode or leak.

DO NOT short-circuit the battery terminals.

DO NO mix used and new batteries.T

DO NO mix alkaline standard (carbon-zinc), lithium T

or rechargeable batteries.

DO NOT use rechargeable batteries in this product.

DO NOT recharge non-rechargeable batteries.

DO NOT allow any part to come in contact with heat

or a direct flame.

DO NOT allow water to come into contact with the

batteries or wiring.

Install carefully to prevent any damage to the batteries

When installing batteries in the battery compartments,

ensure the batteries are placed as marked (+)(-).

Only the recommended batteries should be used.

Remove batteries from product when not in use for long

periods of time.

Keep this product out of the reach of small children.

Store unused batteries in their original packaging.

Dispose of used batteries responsibly.

Safety

Battery Warnings

LCD

Camera

Answer Key Left Key Right Key Menu / OK Key

(1) (2) (3) (4)

S mme Deurspion/li

Gebrui nwijzing Visuele Deurbelksaa

Ver kking & A essoirespa cc

M l verdee ge

H v loe ee

heid

Lett

Opmerking

Bi nsc rmnne he

Bi n LCD-sc rmnne he

Schroef

Tw r af nkelijk v de dikte v de deuree paa , ha an an

Buitencamera

De kabel g t r t in deur en wordt aa doo he gat de

aang en op ndeeslot he ot rdee aanl de Bin ij .nenzde

Stal B gelen eu

G ruik n schroe om t Buiten el aan stal eb ee f he de de en

beug beel e t vestigen

G ruiksaanwieb

j ingz

Ben dh deodig e n

01 Installatie

Verw r uw idi d rspion o b r e gat me e ijde hu ge eu f oo en t en

diameter van minim l mm maaa 13 en xim l 20 mm in uw aa

deu enr op e, geschikte plaats voo he en an ber t bek kij v zoek.

N.B. T t het r uct alti v r e nstallatie.es p od jd óó d i

O t tterijde el v bin n herm (A) pen he ba ks an het ne sc en

pl ts de Micro SD kaar Plaats vervolgens 3 AA aa t.

ba en ootter en ij org ervzr da e juist l ts n.t zgep aa t zij

N.B. Doe rst de Micr SD rt er v rdat e ee o kaa in oo u d

batter en tst.ij plaa

Druk v r ichtig t bin nsc rmoo zhe ne he

(A) er de stalen be el (D) v r ichtig me de k el en schuif t ug op ug , doe oo zt ab ,

naa ene enr b d oda hij vastk kt.zt li

Dr i de door u, basis v deurdikte ko aa op an de ge zen

schr v (B) in de Buitencamera (C), maar draai e niet oe en z

helemaal vast.

Duw rspion (C) vas en de deu t zorg erv r da ka l er oo t de be

ee doo gedurst r wd is en t de pijl op achter de v de , da de zij an

camera n r bov w st.aa en ij

Sluit k el aan door e in aansluiting e drukken, de ab dezde t

u v lt e “K k” als hij op printpl t vas it. Zorg oe en li de aa t z

erv r t kabel juis ge sition rd is, ls e ien in oo da de t po ee zoa t z

de ee afb lding.

In meer detail...

Tec ische specificatieshn

Bi nshuis- der el Afmeti : 6× × mmnne on de ngen 13 75 18

Buitenshuis- r el Afmetin : 30×30×7mmonde de gen

D r t diameter 13mm~20mmeu ga :

O rste de deurdikte: 35mm~105mmnde un

Ba erij 3 AA tterij (niet in repen)tt : ba en beg

Le en uuv sd r ba er : 3 m n ( baseerd op 10 maal g ruiken r tt ij aande ge eb pe

dag)

Voltage 4.5V~3.5V:

Opmerki enng

We rad aen an ne ba om A-merk alkali tterijen an een goe v de kwa tei e li t t

gebruiken.

Pl ts t product nie op ge jke o instabiele o rvlakaa he t on li f ppe ken om sc de ha

doo en oo enr vall te v rkom .

V rkom he pl tsen v oo t aa an het pr uc op te op rvla en, in od t he pe kk

om vin n met n ho luchtvochti eid o v l stof t vel en ge ge ee ge gh f ee , zou ne

ande ag ge ngre ressieve om vi en om da de levensd r van t product dat t uu he

k verkorten.an

D v r ichtig met t plaats voe oo zhe en an be de eu de ka l in d r, om scha e de t

v rkom .oo en

G ruik de stalen ueb be gel (D) en let erop t de p l n r ven da ij aa bo

w s w de kij t, du dan abe ga dan oel door het t. Duw de schr ven

doo en beu enr de gat , t zoda de stal en gel strak eg t de deur it.z

Dr i de schroev aan om de Buitencamera aan de stalen aa en

beug beel e t vestigen

D t kl je woe he ep ee de en de door over ba erijtt , kabel past r

een ne pe ng klei o ni in het klepje.

Vold t alle relev te Eur se richtl n .oe aan an ope ij en

Smartwares verkl rt t t stel, model VD27 vold taa da he toe [ ], oe

aa de be ngn la rijkste ess tiële eisen v de R& E-richt jn,en an TT li

1999/5/EG De vo edige conformiteitverklari is beschikbaar. ll ng

op oe verzk b :ij

Recyc ngli

Di symb l is k als t “ rgekruiste k ko-symb l”.t oo be end he doo li oo

Als di s ol op n produc o een ba erij is gemarkeerd, tek t dit t ymbo ee t f tt be en

da no out he niet me uw t t rmale huish delijk afval m wor n af v rd.ag de ge oe

Sommi ge he en chemisc stoff in elektrische/elektr isc producten of on he

ba nn ootter en kuij en v r de eid en he m i h elijk n amelgezondh t il eu sc ad zij . Z

elektrische/elektr i he apparat en ba erijen alt d on sc en tt ij apa oda dert in, zt

material die d rin i en w r ni w ruikt ku n wor .en aa ztt ee op eu geb nne den

Uw m werki is v vitaal lang vede ng an be oo age der he welslt n van ze

r li en en voor besc rming v het milieuege ng de he an

uitencamera

B r een Ga in de roo t deu

K labe

Bevestigingsschroeven

eur

D. Stalen B geleu

. Bi sc rmnnen he

Product specificaties

Merk:	Smartwares
Categorie:	Intercomsysteem
Model:	VD27
Kleur van het product:	Black, Grey
Gewicht:	380 g
Gewicht verpakking:	325 g
Breedte verpakking:	222 mm
Diepte verpakking:	67 mm
Hoogte verpakking:	139 mm
Materiaal behuizing:	Kunststof
Kleur:	Ja
Beeldschermdiagonaal:	2.8 "
Touchscreen:	Nee
Maximale capaciteit van de geheugenkaart:	32 GB
Connectiviteitstechnologie:	Bedraad
Ondersteunde video-modi:	720p
Compatibele geheugenkaarten:	SD
Binnenunit inbegrepen:	Ja
Buitenunit inbegrepen:	Ja
Batterijen inbegrepen:	Ja
Geheugenkaartslot:	Ja
Instelbaar belvolume:	Ja