Sloan ESD-500 Handleiding
Sloan
Zeepdispenser
ESD-500
Lees hieronder de đ handleiding in het Nederlandse voor Sloan ESD-500 (4 pagina's) in de categorie Zeepdispenser. Deze handleiding was nuttig voor 5 personen en werd door 3 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
SLOAN DECK MOUNTED SOAP DISPENSER (ESD-SERIES) INSTALLATION INSTRUCTIONS
Touchfree Counter Mounted System Installation Guide
If there is a dispenser currently installed
⢠Remove the existing unit, both the above and below counter assemblies
⢠Clean the counter area where the previous dispenser was located
⢠Verify the size of the existing counter hole is 15/16â to 1-1/4â in diameter
If there is no hole in the counter
⢠Prior to drilling, examine below the counter to ensure adequate clearance for the new unit
⢠Drill a 1â diameter hole in the counter top
⢠The hole can be drilled to either the right or left of the faucet, ensuring adequate clearance for the below counter assembly
⢠Clean the counter area where the new hole is located
Code no. 0816203
Rev1 (01/17)
Prior To Installation
New Soap Dispenser Installation:
⢠Ensure that dispenser does not interfere with anything
above or below the lavatory/counter top area
⢠Drill a 1â diameter hole in counter top
⢠Clean area around hole
To Order Replacement Soap Cartridges
800.321.9647
GOJO Industries
Reîlls are also available through your local plumbing or janitorial supply
distributor.
When the soap bottle is empty, a new bottle must be used. The bottle
furnished with the unit is not designed to be reîlled. Altering the bottle and
reîlling it with soap will void the warranty of the product.
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants its Products to be made of îrst class materials, free from defects of material or workmanship under
normal use and to perform the service for which they are intended in a thoroughly reliable and efîcient manner when properly installed and serviced, for
a period of three years (1 year for SF Faucets, special înishes and PWT electronics and 30 days on PWT software) from date of purchase. During this
period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at
customerâs cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs.
This warranty extends only to persons or organizations who purchase Sloan Valve Companyâs products directly from Sloan Valve Company for purpose of
resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
SLOAN ⢠10500 SEYMOUR AVENUE ⢠FRANKLIN PARK, IL 60131
Phone: 1-800-9-VALVE-9 or 1-847-671-4300 ⢠Fax: 1-800-447-8329 or 1-847-671-4380 ⢠www.sloan.com
Improper installation of the
Counter Mounted Dispenser
could result in
breakage.
Dispenser must hang freely
underneath the sink.
Proper installation allows
the unit to vertically hang
beneath the sink.
ESD-1500
ESD-2000
ESD-500
ESD-600 ESD-700 ESD-800
ESD-2100
2
Soap Dispenser Installation
NOTE: ESD-2100 Shown, instructions applicable for all Sloan soap dispensers
Installing the Touchfree Counter Mounted System
Prior to beginning installation, study the exploded view of the Touchfree Counter-Mounted System and locate all the
pieces. Also, look beneath the countertop to and a suitable place for mounting of the Battery Box (9) so that it will not
interfere with system components or plumbing.
Feed the Data Cable 5a and the
shank of the Dispenser Assembly
1 through the hole in the
countertop. Point the spout of the
Dispenser into the sink bowl.
From underneath the counter,
feed the Lock Washer 3 and then
the Mounting Nut 3a over the
Data Cable 5a and onto the
threaded shank of the Dispenser
Assembly 1. Tighten the nut
securely.
Align the indent inside the top of
the Motor Assembly/Bottle
Support 7 with the indent on the
shank of the Dispenser Assembly
1 and îrmly push the Motor
Assembly/Bottle Support up, onto
the shank.
NOTE: Hold the Data Cable îrmly
out of the way as you push up on
the Motor Assembly/Bottle
Support. Continue pushing
upward until the vertical slots in
the Dispenser shank and the
Motor Assembly/Bottle Support
line up.
Secure the Motor Assembly/Bottle
Support 7 to the Dispenser
Assembly 1 shank by pushing the
Retaining Clip 4 into place
through the vertical slots, until it
goes all the way through the Motor
Assembly.
NOTE: Motor Assembly Bottle
Support will rotate 360° to avoid
any obstruction.
Remove the cover from the
Battery Box 8 by loosening the
two captive screws on the Battery
Box cover. Position the Box on a
convenient (vertical or horizontal)
surface under the counter top that
will allow access for battery
changing. Attach the Box to the
surface using the two screws 10
and anchors (if attaching to a
plaster or masonry surface).
Use the Wall Clip 11 to secure the
Power Cable to a wall or other
under-counter surface if desired.
Place four alkaline âDâ Cell
batteries into the Battery Box 9
cover. The batteries must be
positioned according to the
diagrams shown on the inside of
the cover.
NOTE: If the batteries are not
properly installed or the cover is
not properly positioned on the
Box, the System will not work.
Position the cover (with batteries
installed) on the Battery Box and
tighten the two captive screws.
IMPORTANT: Connect the two
halves of the Data Cable 5a
and 5b
by visually lining up the white
stripes on each half and gently
pushing the cable connectors
together until the stripes touch.
Improperly assembled
connectors can cause unit to
not function as intended.
After the batteries are installed in
the battery box, connect the two
halves of the power cable 6a and
6b . Allow 20 seconds before the
system is ready to dispense soap.
3
Soap ReďŹll Bottle Installation and Removal
ReďŹll Installation
(reďŹll sold separately)
9
Feed the dispense tube A on the
Reîll Bottle 9 up through the
Motor Assembly/Bottle Support 7
and Dispenser Assembly 1 ,
aligning the two indents in the
Bottle and the Support. Slide the
Bottle upward until it snaps into
place.
NOTE: The reîll is not properly
installed until you hear the âsnapâ
(as the Green release latch on the
Motor Assembly/Bottle Support 7
engages).
Test the
System by
passing your
hand under
the spout of
the Dispenser
Assembly 1
(in front of the sensor window) at
least three or four times, until
foam soap appears. If the System
does not dispense soap after
passing your hand in front of the
sensor several times, repeat sev-
eral more times. If no sound heard
from motor assembly after placing
hands in front of sensor, check to
see that the Data Cable 6 halves
are îrmly connected, that the
batteries are âgoodâ, and that the
Battery Box 8 cover is properly
positioned and fastened to the
Box. Check for bent contact pins
inside connector 6b . If unit is
multi-activating, check for bent
contact pins inside connector 6b.
ReďŹll Removal
Grasp the empty Reîll Bottle 9
with one hand and use the other
hand to push the Green release
latch on the Motor
Assembly/Bottle Support 7 to
the right (counterclockwise as
seen from above).
Grasp the empty Reîll Bottle 9
with one hand and use the other
hand to push the Green release
latch on the Motor
Assembly/Bottle Support 7 to
the right (counterclockwise as
seen from above).
Soap Replacement
To order replacement soap cartridges:
CONTACT Industries at 800.321.9647 GOJO
Available reîlls
ESD-321 8565-02-N6300GN: 1500 ml Green Certiîed Foam Reîll (2 Pack)
ESD-322 8545-04-N6300GN: 2300 ml Green Certiîed Foam Reîll (4 Pack)
ATTENTION: do not handle by tube. For proper operation, ensure that tubing is
not loose or bent.
Cleaning the Counter Mounted System
Use only mild soap and water to clean the Touchfree Counter Mounted
System spout. Cover the sensor window with your thumb while cleaning the
spout so that you do not continue to dispense soap.
DO NOT use abrasives to clean the TouchFree Counter-Mounted System
(as this may damage the înish or the sensor window).
Product specificaties
| Merk: | Sloan |
| Categorie: | Zeepdispenser |
| Model: | ESD-500 |
Heb je hulp nodig?
Als je hulp nodig hebt met Sloan ESD-500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zeepdispenser Sloan
11 Juni 2025
11 Juni 2025
10 Juni 2025
Handleiding Zeepdispenser
- Zeepdispenser Tiger
- Zeepdispenser Hansgrohe
- Zeepdispenser BTI Aqua-Solutions
- Zeepdispenser DCG
- Zeepdispenser Purell
- Zeepdispenser IKEA
- Zeepdispenser Miomare
- Zeepdispenser Tork
- Zeepdispenser ECG
- Zeepdispenser Lavex
- Zeepdispenser Zack
- Zeepdispenser Tristar
- Zeepdispenser San Jamar
- Zeepdispenser Homedics
- Zeepdispenser Basetech
Nieuwste handleidingen voor Zeepdispenser
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025