Sirui K-20X Handleiding

Sirui Statief K-20X

Lees hieronder de 📖 handleiding in het Nederlandse voor Sirui K-20X (4 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

2.Attaching Your Ball Head

UNC3/8"

Mounting

Screw

4.Attaching and Removing the

Quick Release Plate

3.Know your Quick Release

Clamp and Quick Release Plate

Figure 2-1 Figure 2-2

UNC3/8"

Screw Hole

Tighten

Quick Release Clamp:

Clamp Jaw

Loosen

Bubble Level

Clamp Plate

Security Pin

Clamp locking knob

Security Pin

Release Button

Quick Release Plate:

Common Plate

Tighten

Loosen

Stop

Stop Loosen Press

1.Know Your Ball Head

Friction Adjuster

Dial

Quick Release

Clamp

Main Body

Main Locking

Knob

Panning Base

Support Ball

Panning Base Locking Knob

Figure 4-1

Figure 2-2

Figure 4-3 Figure 4-4

Slide-proof Rubber Mat

KX Series:

Strap holder

Bubble Levels

Figure 3-1

Figure 3-2

1/4" screw with buckle

standard 1/4" screw

1.Know Your Ball Head

2.Attaching Your Ball Head

a.To attach the ball head onto the tripod, you must make

sure that the mounting screw of your tripod is 3/8". If it is

1/4" you will need to get a 3/8" screw or adapter.Many

professional tripods have reversible screws.Please check

your tripod manual for more details.

b.Lock the Panning Base Locking Knob by turning it in a

clockwise direction. As shown on Figure 2-1 & 2-2, align the

3/8" thread hole at the bottom of the Ball Head with the

mounting screw on the tripod. Hold by the base of the Ball

Head and rotate in a clockwise direction until it is locked

tightly.

3.Know your Quick Release Clamp and Quick Release

Plate

4.Attaching and Removing the Quick Release Plate

a.Attaching the QR Plate to Your Camera

Select the QR Plate that matches the base of your

camera.(To prevent excessive wear to the camera's tripod

socket, you should not frequently attach and remove the

Quick Release Plate. It is quite common to leave the QR

Plate permanently attached to the camera.)

The side of the Quick Release Plate with the slide-proof

rubber mat must be facing the base of the camera. Make

sure the QR Plate screw aligns with the tripod socket on the

bottom of the camera.

Position the QR plate on the camera body and tighten the

screw with a coin or allen key. If you plan to keep the quick

release plate on your camera for a long period of time or you

are using medium or large format cameras, you should

tighten the screw with the allen key.

b.Attaching the camera with QR Plate onto the Ball Head

Slightly loosen the Clamp Locking Knob by turning it

counter-clockwise, slide the QR plate laterally into the Quick

Release Clamp (Figure 4-1) and tighten the clamp by turning

clockwise. Another method is to fully open the Clamp

Locking Knob and place the plate in from the top (Figure 4-

2). Tighten the knob to lock the camera in place.

c.Security Pin on the Quick Release Clamp

There is a safety lock on the top of the Quick Release Clamp

that effectively prevents the camera from sliding off of the

clamp if it is slightly loosened (Figure 4-3). This allows you to

make minor adjustments of the camera position on the Ball

Head without worrying about the camera sliding off of the

Quick Release Clamp. This feature is available with all Sirui

QR plates. (Warning: While other styles of QR plates can be

used on Sirui Ball Heads, this safety feature may not be

available with other brands of QR plates. Even with the Sirui

QR Plates,you should hold your camera while loosening the

Quick Release Clamp).

d.Removing the Camera with QR Plate from the Ball Head

While holding the camera, loosen the Clamp Locking Knob

by slightly turning it counter-clock-wise. Push in the

Security Pin Release Button and slide the camera off of the

Clamp Plate (Figure 4-4). You can also remove the camera

by fully opening the clamp and lifting the camera out of the

clamp.

KX B H Series all ead

INSTRUCTIONS

Professional Photographic Equipment

Address: The Third ndustrial District,Wuguishan Town,Zhongshan City,Guangdong,China

E-mail: info@sirui-photo.com http://www.sirui-photo.com http://www.zssirui.com

Tel: 0086-760-88897373 Fax: 0086-760-88207062 P.C: 528458

Service Hotline: (0086)400 830 2299

SIRUI Photographic Equipment Industry(Zhongshan) CO.,Ltd

K 10X-

K-20X

K-30X

K-40X

0.35/0.77

0.4/0.88

0.5/1.10

0.8/1.76

20/44.1

25/55.1

30/66.1

35/77.2

Diameter

mm/inch

Weight

kg/lb

Maximum

Load

kg/lb

KX Series Ball Head Data Char t

Height

mm/inch

93/3.7

98/3.9

106/4.2

124/4.9

33/1.3

38/1.5

44/1.7

54/2.1

7.Adjusting the Ball Head

8.Unlocking the Ball Head：

Figure 5-1 Figure 5-3

Figure 5-2 Figure 5-4

Tighten

Loosen

Tighten

Loosen

Tighten

Loosen

Figure 7-1

Figure 7-2 Figure 8-1 Figure 8-2

Tighten

Loosen

6 Basic Operation. :5 Factory Setting.

Specifications are subject to change without notice.

Announcements

Do not exceed the recommended load limit of the ball head and/or tripod. (Please refer to product specifications)

Please make sure that the locks are securely tightened when in use.

This product should not be used in environments that exceed the following conditions (-40 ~ +100°C/-40 ~212°F).

When used in damp, dirty or dusty environments, please clean and dry thoroughly after use, to assure proper functioning in the

future.

Please keep from high temperatures and direct exposure to bright sunlight for extended periods of time.

To protect your camera gear, please remove it from the tripod/ball head when transporting from place to place.

Prevent sand, grit and other foreign matter from getting into the interior of the Ball Head. If the Ball Head does not move smoothly,

please use a clean, soft cloth to gently wipe the Ball mechanism.

There is no need to lubricate any parts of this product. The addition of lubricants will gum up the mechanisms and reduce their

normal gliding characteristics. The construction of Sirui professional Ball Heads is very precise, so extra maintenance is not

needed.

Please keep this product away from all electrical power sources.

e.Camera Screw Usage

The 1/4" screw with buckle can only be used in the middle

slot of the QR Plate. The standard 1/4” screw can be used in

the left or right slot, if the position of your camera's 1/4"

tripod socket is off-center , as shown in Figure 3-2.

5.Factory Setting

a.As shown in Figure 5-1, turn the Main Locking Knob in a

clockwise direction about 1/2 turn. Next, turn the Friction

Adjustment Dial in a counter-clockwise direction until it

stops. Loosen the Main Locking Knob by turning in a

counter-clockwise direction until it stops.

b.As shown in Figure 5-2, while slowly rocking the camera,

turn the Main Locking Knob clockwise until you feel the

resistance you desire. Then turn the Friction Adjustment Dial

clockwise until it stops (Figure 5-3).

c.Turn the blue Calibration Ring (around the Main Locking

Knob) to the 0 position (Figure 5-4).

6.Basic Operation

7.Adjusting the Ball Head

Mount your camera onto the Ball Head. While holding the

camera, loosen the Main Locking Knob (Figure 7-1). The ball

head will be very loose, so you will need to adjust the

amount of resistance you prefer. Rotate the Friction

Adjustment Knob that is in the Main Locking Knob in a

counter-clockwise position until it stops. While slowly rocking

the camera, tighten the Main Locking Knob until you feel the

resistance you desire. The friction adjustment should be set

so that there is enough resistance to prevent the camera

from easily tipping over, while giving you the ability to make

adjustments to camera position without having to use

excessive force. This becomes very useful when using

telephoto lenses and when critical alignments need to be

made. When the resistance level you want is achieved, stop

turning the Main Locking Knob. Turn the Friction Adjustment

Knob in a clockwise position until it stops (Figure 7-2).

You may want to start shooting immediately or you can

tighten the Main Locking Knob to firmly lock the head in

place. Before locking the Ball Head, you may want to use

the bubble levels to make sure it will be horizontal.

8.Unlocking the Ball Head

You may find that the Ball Head is locked in position (usually

from excessive force) and needs to be released. Please

follow the below instructions, paying attention to the turning

directions.

If possible, mount the Ball Head on the tripod and turn the

Main Locking Knob in a clockwise direction (Figure 8-1).

Turn the Friction Adjustment Dial in a counter-clockwise

direction until it stops (Figure 8-2).

Note: the Quick Release plate has a strap holder that allows

you to attach many popular camera straps directly onto

the plate. Please make sure that the Quick Release

plate is securely attached to the camera, to prevent the

possibility of the camera detaching from the plate.

Please check this attachment regularly.

Professional Photographic Equipment

www.sirui-photo.com / www.zssirui.com

KX B H Series all ead

INSTRUCTIONS

SIRUI Photographic Equipment Industry(Zho ngshan) CO.,Ltd

Address: The Third Industrial District,Wuguishan Town,Zhongshan

City,Guangdong,China

Tel: 0086-760-88897373

Fax: 0086-760-88207062

P.C: 528458

E-mail: info@sirui-photo.com

http://www.sirui-photo.com http://www.zssirui.com

Service Hotline: (0086)400 830 2299

Product specificaties

Merk:	Sirui
Categorie:	Statief
Model:	K-20X
Kleur van het product:	Zwart
Gewicht:	400 g
Hoogte:	98 mm
Diameter:	38 mm
Maximale gewichtscapaciteit:	25 kg
Materiaal:	Aluminium
Bijlage:	Universeel "
Tripod head type:	Ball head