Singularity Computers Resonance Dual Handleiding
Singularity Computers
Niet gecategoriseerd
Resonance Dual
Bekijk gratis de handleiding van Singularity Computers Resonance Dual (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.6 sterren uit 2 reviews. Heb je een vraag over Singularity Computers Resonance Dual of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
Port Layouts
*Graphics used represent Resonance Dual
Tools Required
Step 3
Attach both ‘ ’ Universal Back Plates to both ‘Mounting
Blocks’ using 4x 3A.
N :OTE Resonance can be removed from the mounting
system by undoing 2x2A to give you access to the area
behind for tightening the back plate fasteners to the
radiator, fittings etc.
Pressure Testing
Do not exceed normal range when pressure testing.
• M4 A – llen key Not included
• M4 Socket Wrench – Not included
Fasteners
1A
(2x)
2A
(2x)
M4
Washer
3A
(4x)
2B
(2x)
M4
Nut
⚠ OVER TIGHTENING OF FASTENERS ON ACRYLIC WILL RESULT IN CRACKS. ⚠
Step 1
Attach ‘LED Strip’ ‘ ’ to LED Strip Mount using included
adhesive. Then attach 'LED Strip Mount' to 'Mounting
Panel' with 2x 1A.
Filling
⚠INCLUDED RUBBER STOP PLUGS ARE ONLY PART OF
PACKAGING, DO NOT USE AS STOP FITTINGS.
NOTE: For Resonance Dual only run one D5 Pump until the
loop is full and all of the air is removed.
Use external power source to power your pump while
you are filling your loop. Do not boot your system until
your loop is full, some remaining air is fine at this
point. Use a fill tube at least 30 50cm long and attach -
to one of the top ports of Resonance with a 90-degree
fitting. Fill until fill tube is half full each time the
reservoir is drained when you switch on the pump. Do
not detach the fill tube until all of the air is out of the
loop even if this means running your system for a few
hours with it still attached. Resonance is different to
fill to a normal tube reservoir, there can be no air gap
at the top, it needs to be entirely full of fluid. The
bigger your loop volume the longer the system will
take to bleed (also depending on other factors such as
loop complexity and flow restriction). Let Resonance
do the work for you, it is best to just leave it running
and the air will come out on its own. It is only a matter
of time and all of the air will always come out.
Step 2
Attach 'Mounting Block' to 'Mounting Panel' with 2x 2A
and 2x M4 Washers. Select mounting position for your
radiator size based on diagram below:
Then Attach 'Mounting Panel' to Resonance Manifold
with 2x 2B, 2x M4 Washers and 2x M4 Nuts.
Lighting
Resonance comes included with a 30cm RGB LED strip. It is a slim low profile PCB LED strip with a
standard 4pin RGB connection with a male/female adapter. Plug this into any 4pin RGB connection on
your motherboard.
Product specificaties
| Merk: | Singularity Computers |
| Categorie: | Niet gecategoriseerd |
| Model: | Resonance Dual |
Heb je hulp nodig?
Als je hulp nodig hebt met Singularity Computers Resonance Dual stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Singularity Computers
19 Februari 2025
Handleiding Niet gecategoriseerd
- Petsafe
- Itechworld
- Natuzzi
- ClearOne
- United Office
- Gaggia
- Leen Bakker
- Nesco
- Savic
- ToiToiKids
- Riello
- Carnielli
- A-Designs
- ChamSys
- Cressi
Nieuwste handleidingen voor Niet gecategoriseerd
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025