Shimano SL-R780 Handleiding

Shimano Fietsaccessoire SL-R780

Lees hieronder de 📖 handleiding in het Nederlandse voor Shimano SL-R780 (2 pagina's) in de categorie Fietsaccessoire. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Shifting lever unit mounting screw (Large)

Shifting lever unit mounting screw (Small)

To shift from a small chainring to a larger chainring

(Lever A)

When lever (A) is pressed once,

there is a shift of one step from

a small chainring to a larger

chainring.

Example:

from intermediate

chainring to largest

chainring.

General Safety Information

WARNING

• Obtain and read the service instructions carefully prior to installing the parts.

Loose, worn or damaged parts may cause the bicycle to fall over and serious injury

may occur as a result. We strongly recommend only using genuine Shimano

replacement parts.

• Obtain and read the service instructions carefully prior to installing the parts. If

adjustments are not carried out correctly, the chain may come off and this may

cause you to fall off the bicycle which could result in serious injury.

• Read these Technical Service Instructions carefully, and keep them in a safe place

for later reference.

Note

• For smooth operation, use the specified outer casing and bottom bracket cable

guide.

• Grease the inner cable and the inside of the outer casing before use to ensure that

they slide properly.

• Use a frame with internal cable routing is strongly discouraged as it has tendencies

to impair the SIS shifting function due to its high cable resistance.

• Operation of the levers related to gear shifting should be made only when the front

chainwheel is turning.

• Use an outer casing which still has some length to spare even when the

handlebars are turned all the way to both sides. Furthermore, check that the

shifting lever does not touch the bicycle frame when the handlebars are turned all

the way.

• A special grease is used for the gear shifting cable. Do not use DURA-ACE grease

or other types of grease, otherwise they may cause deterioration in gear shifting

performance.

• Do not disassemble the indicator and shifting lever unit, as this may damage them

or cause mis-operation.

• Parts are not guaranteed against natural wear or deterioration resulting from

normal use.

• For maximum performance we highly recommend Shimano lubricants and

maintenance products.

• For any questions regarding methods of installation, adjustment, maintenance or

operation, please contact a professional bicycle dealer.

Shifting lever

When lever (B) is operated, there is one click where trimming

(the noise prevention mechanism) engages, and a second

stronger click when the gear shift stroke is completed. After

trimming, the next push will complete the gear shift stroke.

Freehub FH-6700 / FH-5700

OT-SP41

Outer casing

FD-6700 / FD-5700 FD-4600

FC-4600 / FC-4650

RD-4600

FH-4600

CS-4600

CN-4601

FC-6700 / FC-6750

FC-5700 / FC-5750

CN-6701/ CN-5701

SM-SP17

SL-R780 SL-4600

Shifting lever Front

Rear

Gears

Front derailleur

Front chainwheel

Chain

Bottom bracket cable guide

Cassette sprocket CS-6700 / CS-5700

Rear derailleur RD-6700 / RD-5700

Front

Rear

In order to realize the best performance, we recommend that the following

combination be used.

Freehub FH-6700 / FH-5700

OT-SP41

Outer casing

FD-6703 / FD-5703 FD-4603

FC-4603

RD-4600

FH-4600

CS-4600

CN-5600

FC-6703 / FC-5703

CN-6600 / CN-5600

SM-SP17

SL-R783 SL-4603

SL-R780 SL-4600

Gears

Front derailleur

Front chainwheel

Chain

Bottom bracket cable guide

Cassette sprocket CS-6700 / CS-5700

Rear derailleur RD-6700 / RD-5700

Technical Service Instructions SI-6UR0A-001

Shifting lever

SL-R780 / SL-R783

SL-4600 / SL-4603

To shift from a large chainring to a smaller chainring

(Lever B)

When lever (B) is pressed once,

there is a shift of one step from

a large chainring to a smaller

chainring.

Example:

from largest chainring to

intermediate chainring.

This release lever is equipped with a 2-way release mechanism which allows release operations to be carried out by either pushing or pulling

the lever. Both lever (A) and lever (B) always return to the initial position when they are released after shifting. When operating one of the

levers, always be sure to turn the crank arm at the same time.

Gear shifting operation

Trimming (noise prevention operation)

If the chain is on the large front chainwheel and the larger rear

sprocket, the chain will rub in the front derailleur plate,

producing a characteristic noise. When this happens, press

lever (B) lightly (to the point where it clicks); this causes the

front derailleur to move slightly

towards the smaller chainwheel,

thereby eliminating the noise.

Movement of the

front derailleur

Chain position

Mounting the shifting lever

Use a handlebar grip with a maximum outer diameter of 32 mm (SL-R780) /

36 mm (SL-4600).

< Front > < Rear >

1. Loosen the cable fixing bolt (nut) of the front derailleur or rear derailleur, and then pull the inner cable out of

the shifting lever unit in the same way as when installing the inner cable.

2. Remove the indicator unit by following the disassembly procedure given in “Replacement and assembly of

the indicator unit”.

3. Remove the four shifting lever unit mounting screws, and then remove the shifting lever unit as shown in the

illustration.

4. Align the shifting lever unit and the bracket, and then secure with the four shifting lever unit mounting

screws.

5. Install the indicator unit by following the assembly procedure given in “Replacement and assembly of the

indicator unit”.

Disassembly and reassembly should only be carried out when

replacing the shifting lever unit.

Disassembly and reassembly should only be carried out when the

indicator unit is being replaced.

< Disassembly >

1. Remove the two indicator fixing screws.

2. Turn the indicator unit in the clockwise direction as shown in the

illustration, and then lift it up to remove it.

(For the front: Turn it counterclockwise.)

< Assembly >

1. Operate lever B 9 times or more to set it to the highest position.

(For the front: Operate lever B 2 times or more to set it to the lowest position.)

2. Check that the indicator needle is at the left edge.

(For the front: Check that the needle is at the right edge.)

3. Insert the pin at the bottom of the indicator into the hole in the winder unit and

then insert the indicator unit so that the two bosses are aligned with the

marks on the shifting lever unit.

4. Turn the indicator unit counterclockwise as shown in the illustration to install it.

(For the front: Turn it clockwise.)

5. Secure the indicator unit by tightening the two indicator fixing screws.

6. Check the operation. If the indicator unit does not operate correctly,

reassemble while paying particular attention to steps 1, 2 and 3.

Replacement and assembly of the indicator unit

Replacement of the shifting lever unit

Installing the shifting cable

Cutting the outer casing

When cutting the outer casing, cut the

opposite end to the end with the marking.

After cutting the outer casing, make the

end round so that the inside of the hole

has a uniform diameter.

Attach the same outer end

cap to the cut end of the

outer casing.

Outer end cap

Lever (B)

Trim operation

Click

Gear shift

complete stroke

Tightening torque :

3 N·m {26 in. lbs.}

< Rear >< Front >

Note:

When installing the components to carbon frame/handle bar surfaces, verify with the

manufacturer of the carbon frame/parts for their recommendation on tightening torque in

order to prevent over tightening that can cause damage to the carbon material and/or

under tightening that can cause lack of fixing strength for the components.

• Install the shifting lever in a position where it will not obstruct brake operation

and gear shifting operation.

• Do not use in a combination which causes brake operation to be obstructed.

SI-6UR0A-001-00

Installing the inner cable

1. Operate lever B 9 times or more to set it to the highest position.

(For the front: Operate lever B 2 times or more to set it to the lowest

position.)

2. Check that the indicator needle is at the left edge.

(For the front: Check that the needle is at the right edge.)

3. Remove the inner hole cover and install the cable.

Install the inner hole cover by turning it as shown in the illustration until it

stops.

Do not turn it any further than this, otherwise it may damage the screw

thread.

Lever (B)

* The illustration shows the rear lever.

Inner hole cover

Inner cable

Bosses

Indicator fixing screws

Indicator unit

Winder hole

4 mm Allen key

This service instruction explains how to use and maintain the

Shimano bicycle parts which have been used on your new bicycle.

For any questions regarding your bicycle or other matters which

are not related to Shimano parts, please contact the place of

purchase or the bicycle manufacturer.

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

* Service Instructions in further languages are available at :

http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

The levers are equipped with a multi release function which lets you

shift two gears with a single release operation. (SL-R780 only)

To shift from a small sprocket to a larger sprocket

(Lever A)

You can vary the lever stroke to shift the desired number of gears,

so that to shift by one gear only, move the lever to the (1) position,

and to shift by two gears at one time, move the lever to the (2)

position. A maximum two-gear shift can be made in this manner.

To shift from a large sprocket to a smaller sprocket

(Lever B)

< SL-R780 >

You can vary the lever stroke to shift the desired number of gears,

so that to shift by one gear only, move the lever to the (1) position,

and to shift by two gears at one time, move the lever to the (2)

position. A maximum two-gear shift can be made in this manner.

< SL-4600 >

Press lever (B) once to shift one step from a larger to a smaller

sprocket.

Lever (B)

• 2-WAY RELEASE

• MULTI RELEASE

Lever (A) initial position

Lever (B)

2-WAY RELEASE

Tightening torque:

0.08 N·m {0.7 in. lbs.}

Tightening torque:

0.14 N·m {1.2 in. lbs.}

Tightening torque:

0.14 N·m {1.2 in. lbs.}

Lever (A) initial position

Lever (B)

2-WAY RELEASE

Product specificaties

Merk:	Shimano
Categorie:	Fietsaccessoire
Model:	SL-R780

Heb je hulp nodig?

Als je hulp nodig hebt met Shimano SL-R780 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fietsaccessoire Shimano

Shimano ST-M4000-L Handleiding

12 Juni 2023

Shimano FD-M8000-H Handleiding

9 Juni 2023

Shimano RD-4700-SS Handleiding

8 Juni 2023

Shimano SL-3S35E Handleiding

6 Juni 2023

Shimano FD-R3030-B Handleiding

4 Juni 2023

Shimano FD-M8025-H Handleiding

23 Mei 2023

Shimano ST-9071 Handleiding

22 Mei 2023

Shimano FD-M4000-TS6 Handleiding

21 Mei 2023

Shimano FD-5801-B Handleiding

20 Mei 2023

Shimano EW-CP100 Handleiding

20 Mei 2023

Handleiding Fietsaccessoire

Nieuwste handleidingen voor Fietsaccessoire

Basil Bremen Handleiding

5 Maart 2024

Basil SoHo Handleiding

5 Maart 2024

Basil Cento Handleiding

5 Maart 2024

Basil Buddy Handleiding

5 Maart 2024

Pletscher Prisma 53203.00 Handleiding

27 Februari 2024

Kayoba 004-435 Handleiding

6 December 2023

Kayoba 004-431 Handleiding

6 December 2023

Spokey Pumptrack Handleiding

16 November 2023

Knog Oi Classic Large Handleiding

13 September 2023

Knog Oi Classic Small Handleiding

12 September 2023