Shimano FH-T780 Handleiding

Shimano Niet gecategoriseerd FH-T780

Lees hieronder de 📖 handleiding in het Nederlandse voor Shimano FH-T780 (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
General Safety Information
WARNING
Check that the wheels are fastened securely before riding the bicycle. If the wheels are
●
loose in any way, they may come off the bicycle and serious injury may result.
●Obtain and read the service instructions carefully prior to installing the parts.
Loose, worn, or damaged parts may cause injury to the rider.
We strongly recommend only using genuine Shimano replacement parts.
Read these Technical Service Instructions carefully, and keep them in a safe place for
●
later reference.
Note
Use the CS-M771-10 in combination with an MTB 10-speed chain.
●
If the wheel becomes stiff and diffi cult to turn, you should lubricate it with grease.
●
Do not apply any oil to the inside of the hub, otherwise the grease will come out.
●
You should periodically wash the sprockets in a neutral detergent and then lubricate
●
them again. In addition, cleaning the chain with neutral detergent and lubricating it can be
a effective way of extending the useful life of the sprockets and the chain.
If the chain keeps coming off the sprockets during use, replace the sprockets and the
●
chain.
Parts are not guaranteed against natural wear or deterioration resulting from normal use.
●
For maximum performance we highly recommend Shimano lubricants and maintenance
●
products.
Technical Service Instructions SI-3TG0A-002
FH-M785 / HB-M785
FH-T780 / HB-T780
Freehub / Front hub
Specifi cations
Freehub / Front hub
Freehub Front hub
Model No. FH-M785 FH-T780 HB-M785 HB-T780
Gears 10 ––
No. of spoke holes 32 / 36 32 / 36
Overlock nut dimensions 135 mm 100 mm
Applicable brakes Disc brake Rim brake Disc brake Rim brake
Cassette sprocket tooth combination
Model number Group name Gears Tooth combination
CS-M771-10
bJ 10 11, 13, 15, 17, 19, 21, 23, 26, 30, 34T
bK 10 11, 13, 15, 17, 19, 21, 24, 28, 32, 36T
bL 10 11, 12, 14, 16, 18, 20, 22, 25, 28, 32T
CS-6700 – 10 11, 12, 13, 14, 15, 17, 19, 21, 24, 28T
* The RD-M780 cannot be used in combination with the CS-6700 (11-28T).
* The RD-T780 cannot be used in combination with the CS-M771-10 (11-36T).
<FH-M785 / FH-T780>
Installation of the HG sprockets
For each sprocket, the surface that
has the group mark should face
outward and be positioned so that
the wide parts of the gear projections
on each sprocket and the A part
(where the groove width is wide) of
the freewheel body are aligned.
< >CS-M771-10
(bJ) 11 - 34T
(bK) 11 - 36T
(bL) 11 - 32T
<CS-6700>
11 - 28T
For installation of the HG sprockets, use the special tool
(TL-LR15/LR10) to tighten the lock ring.
Tightening torque:
30 - 50 N·m {261 - 435 in. lbs}
To replace the HG sprockets, use the special tool
(TL-LR15/LR10) and TL-SR21 to remove the lock ring.
A
The groove is wide
at one place only.
Wide part
Tool
(TL-SR21)
Disassembly
TL-LR15 / LR10
Lock ring
Lock ring
Lock ring
Sprocket spacer Sprocket spacer
Spacer
Lock ring spacer
Lock ring spacer
Replacement of the freewheel body
First, pull out the hub axle by following the procedure shown in the illustration. (FH-M785)
The double-lock section at the freewheel side cannot be disassembled.
(1)
Disassembly
5 mm Allen key 17mm spanner
(2)
Rotor fi xing serrations
Seal
Cone with dust cover
(Cannot be disassembled) Lip is on the outside
Left side Tightening torque:
15 - 20 N·m {131 - 174 in. lbs.}
(3)
Hub axle
Note:
When removing and installing the seal, do it very
●
carefully so that the seal does not become bent.
When reinstalling the seal, make sure that it is facing
the right way, and insert it as far as it will go.
Do not disassemble the dust-proof cover which is
●
crimped onto the cone.
The rotor fi xing serrations may become damaged
●
if the disc brake rotor has not been installed to the
FH-M785, so install the accessory rotor mount cover.
After removing the hub axle, remove the freewheel body
fi xing bolt (inside the freewheel body), and then replace the
freewheel body.
Note:
Be sure to apply grease to the the thread of the
freewheel body fi xing bolt, otherwise looseness or
sticking may occur.
Do not attempt to disassemble
the freewheel body, because it
may result in a malfunction.
<HB-M785>
Maintenance
The unit can be disassembled as
shown in the illustration.
Apply grease to the various parts at
periodic intervals.
Note:
The HB-M785 cannot be disassembled from the left side of the
●
hub unit (the rotor fi xing serration side).
When removing and installing the seal, do it very carefully so that
●
the seal does not become bent.
When reinstalling the seal, make sure that it is facing the right way,
and insert it as far as it will go.
The rotor fi xing serrations may become damaged if the disc
●
brake rotor has not been installed to the HB-M785, so install the
accessory rotor mount cover.
<Assembly>
Use the special tool (TL-HS22/HS20 /17mm)
for installing the hub axle and a 5 mm Allen
key to tighten the lock nut so as to double-lock
the mechanism as shown in the illustration.
Tightening torque:
15 - 17 N·m {131 - 148 in. lbs.}
5 mm Allen key
Tighten
TL-HS22/HS20
Hub axle
<FH-M785 / HB-M785>
Wheel spoke lacing
Check that the spokes have been laced as shown in
the illustration.
A radial assembly cannot be used.
Rotating direction of wheel
Front left Rear left Rear right Front right
Installation of the rotor
Rotor fi xing lock ring
TL-LR15
Tightening torque:
40 - 50 N·m {348 - 435 in. lbs}
14 mm Allen key
Seal
Seal
Rotor mount cover
SI-3TG0A-002-00
Applying grease
DURA-ACE grease
(Y-04110000)
Freewheel body
washer (FH-M785)
Freewheel body
fi xing bolt
Do not disassemble
the seal.
Freewheel body
© Jan. 2011 by Shimano Inc. AWS Printed in Malaysia.
* Service Instructions in further languages are available at: http://techdocs.shimano.com
Please note: Specifi cations are subject to change for improvement without notice. (English)
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Tightening torque:
45 - 50 N·m {392 - 435 in. lbs.}

Product specificaties

Merk: Shimano
Categorie: Niet gecategoriseerd
Model: FH-T780

Heb je hulp nodig?

Als je hulp nodig hebt met Shimano FH-T780 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Shimano

Shimano

Shimano BR-C6060-F Handleiding

29 Augustus 2023
Shimano

Shimano WH-R9270-C60-HR-TL-F Handleiding

6 Juli 2023
Shimano

Shimano BR-M9020 Handleiding

6 Juli 2023
Shimano

Shimano BB-MT800-PA Handleiding

6 Juli 2023
Shimano

Shimano RD-M3020-8 Handleiding

5 Juli 2023
Shimano

Shimano SM-BB71-41B Handleiding

5 Juli 2023
Shimano

Shimano RD-9070-SS Handleiding

5 Juli 2023
Shimano

Shimano SM-BB71-41C Handleiding

4 Juli 2023
Shimano

Shimano SL-M6100-IR Handleiding

3 Juli 2023
Shimano

Shimano BB-RS501 Handleiding

2 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024