Scotts HT10020S Handleiding

Scotts Grasmaaier HT10020S

Lees hieronder de 📖 handleiding in het Nederlandse voor Scotts HT10020S (24 pagina's) in de categorie Grasmaaier. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24

OWNER’S MANUAL

ELECTRIC HEDGE TRIMMER

Model HT10020S

Your hedge trimmer has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual before

using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PARTS, SERVICE QUESTIONS? GO TO SCOTTS.AMERICANLAWNMOWER.COM

OR CALL 1-800-618-7474 BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

3120341

GENERAL POWER TOOL SAFETY WARNINGS

IMPORTANT SAFETY WARNINGS

Model HT10020S

WARNING: Read all safety warnings and instructions. Failure to

follow the warnings and instructions may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for future reference. The term

“power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

 Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

 Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

 Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

Electrical safety

 Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matching outlets

will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or

grounded.

 Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

 Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

 When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of electric

shock.

Personal safety

 Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools

may result in serious personal injury.

 Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce the risk of personal injuries.

 Prevent unintentional starting. Ensure the switch is in the off

-position before connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools that have the

switch on invites accidents.

 Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

 Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in

unexpected situations.

 Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

 If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

Power tool use and care

 Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

 Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

 Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

 Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed. Use

of the power tool for operations different from those intended

could result in a hazardous situation.

Service

 Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

 When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance instructions may create a

risk of shock or injury.

HEDGE TRIMMER SAFETY WARNINGS

EXTENSION CORD. Make sure your extension cord is in good

condition. When using an extension cord, be sure it is heavy enough

to carry the current your product will draw. An undersized extension

cord will cause a drop in line voltage resulting in loss of power

and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt,

use the next heavier gage. The smaller the gage number, the

heavier the cord.

WARNING: Use out door extension cords marked SW-A, SOW-A,

STW-A, SJW-A, or SJTW-A. These cords are rated for outdoor use

and reduce the risk of electric shock.

DOUBLE INSULATION—Double Insulation is a concept in safety in

electric power tools, which eliminates the need for the usual

three-wire grounded power cord. All exposed metal parts are

isolated from the internal metal motor components with protecting

insulation. Double insulated tools do not need to be grounded.

NOTE: The double insulated system is intended to protect the user

from shock resulting from a break in the tool’s internal insulation.

Observe all normal safety precautions to avoid electrical shock.

It is possible to tie the extension cord and power cord

in a knot to prevent them from becoming disconnected

during use. Make the knot as shown, then connect the

plug end of the power cord into the receptacle end of

the extension cord. This method can also be used to

tie two extension cords together.

POLARIZED PLUGS—To reduce the risk of electric shock, this

equipment has a polarized plug (one blade is wider than the other).

This equipment must be used with a suitable polarized 2 wire or 3

wire extension cord. Polarized connections will fit together only one

way. Make sure that the receptacle end of the extension cord has

large and small blade slot widths. If the plug does not fit fully into the

extension cord, reverse the plug. If it still does not fit obtain a suitable

extension cord. If the extension cord does not fit fully into the outlet,

contact a qualified electrician to install the proper outlet. Do not

change the tool plug or extension cord in any way.

CHECK DAMAGED PARTS – Before further use of the hedge

trimmer, a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform its

intended function. Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting and any other condition

that may affect its operation. A guard or other part that is damaged

should be properly repaired or replaced. Call our customer service

help line at 1-800-618-7474 for assistance.

WARNING: California Proposition 65: This product contains

chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm.

WARNING: Some dust and debris created by the use of this tool

could contain chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm. Some examples

of these chemicals are:

 Chemicals in fertilizers

 Compounds in insecticides, herbicides and

pesticides

 Arsenic and chromium from chemically treated lumber

Your risk from exposure to these chemicals varies, depending on how

often you do this type of work. To reduce your exposure, work in a

well-ventilated area and with approved safety equipment, such as

dust masks that are specially designed to filter out microscopic

particles.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not More American wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

 DANGER – Keep hands away from blade. Contact with blade will

result in serious personal injury.

 Use both hands when operating the hedge trimmer. Using one

hand could cause loss of control and result in serious

personal injury.

 Keep all parts of the body away from the cutter blade. Do not

remove cut material or hold material to be cut when blades are

moving. Make sure the switch is off when clearing jammed

material. Blades coast after turn off. A moment of inattention

while operating the hedge trimmer may result in serious personal

injury.

 Carry the hedge trimmer by the handle with the cutter blade

stopped. Proper handling of the hedge trimmer will reduce

possible personal injury from the cutter blades.

 Hold the power tool by insulated gripping surfaces only,

because the cutter blade may contact hidden wiring or its

own cord. Cutter blades contacting a “live” wire may make

exposed metal parts of the power tool “live” and could give the

operator an electric shock.

 Keep cable away from cutting area. During operation the

cable may be hidden in shrubs and can be accidentally cut by

the blade.

WARNING – Only use with handle and guard properly assembled to

hedge trimmer. The use of the hedge trimmer without the proper

guard or handle provided may result in serious personal injury.

Model HT10020S

Product specificaties

Merk:	Scotts
Categorie:	Grasmaaier
Model:	HT10020S

Heb je hulp nodig?

Als je hulp nodig hebt met Scotts HT10020S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Grasmaaier Scotts

Scotts LB22020S Handleiding

13 Juni 2023

Scotts LB23020S Handleiding

8 Juni 2023

Scotts LPS40820S Handleiding

6 Juni 2023

Scotts LHT12220S Handleiding

4 Juni 2023

Scotts LB24020S Handleiding

28 Mei 2023

Scotts CLPS40020S Handleiding

27 Mei 2023

Scotts PS45010S Handleiding

26 Mei 2023

Scotts LCS31020S Handleiding

25 Mei 2023

Scotts HT10020S Handleiding

24 Mei 2023

Scotts LST02012S Handleiding

20 Mei 2023

Handleiding Grasmaaier

Nieuwste handleidingen voor Grasmaaier

Garda GBR 51 S HW Handleiding

25 April 2024

Garda GAR 40 S-P Handleiding

25 April 2024

Bestgreen BG Serie 1 36 Li Handleiding

18 April 2024

Powerbase PBPM 40P Handleiding

18 April 2024

Worx WG330E Handleiding

17 April 2024

Fieldmann FZR 5316-170B Handleiding

11 April 2024

Fieldmann FZR 4006-80BH Handleiding

11 April 2024

Cub Cadet Ultima ZTS1 46 Handleiding

9 April 2024

Cub Cadet Tank M72-CAT Handleiding

9 April 2024

Cub Cadet Tank M60 KH Handleiding

9 April 2024