Scosche ITCGM01B Handleiding
Scosche
Niet gecategoriseerd
ITCGM01B
Bekijk gratis de handleiding van Scosche ITCGM01B (12 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.8 sterren uit 2 reviews. Heb je een vraag over Scosche ITCGM01B of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/12
ITCGM01B
IN-DASH STEREO INSTALLATION KIT FOR
2010-14 CHEVROLET CAMARO
WITH TOUCH-SCREEN INTERFACE
*Dash modification required*
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/
codes and information pertaining to installation of this kit (ITCGM01B) in 2010-14 Chevrolet Camaro vehicles. Scosche Industries,
Inc. cannot be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes
or options, or damage that may occur in the automobile during the installation of components while using this booklet.
©2017 SCOSCHE INDUSTRIES, INC.
ITCGM01B 05/17
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
INTRODUCTION/PRELIMINARY
This premium installation kit is for 2010-14 Chevrolet Camaro vehicles. Included are all the parts
you need to mount your car stereo or CD player into your vehicle’s dash. Refer to the individual
instruction in this manual to remove your vehicle’s factory radio and assemble the kit. *Dash
modification required see page 2.
CAUTION
DISCONNECT YOUR VEHICLE’S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION
TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM
METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE
CAN CAUSE DAMAGE TO THE VEHICLE’S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID
ALL FACTORY AIRBAG WIRING - AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS
INJURY OR DEATH.
NOTES
• See your vehicle’s instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo for proper wiring and mounting instructions.
1. Main panel with built-in touch screen (
*
)
2. Hazard Warning Flasher
3. Stereo mounting bracket (left)
4. Stereo mounting bracket (right)
5. Dash pocket for single din mount
6. Power harness (not shown-see page 3)
SOLD SEPARATELY:
CAMOSM OnStar retention interface
(not shown -see page 5)
1
2
5
*
3
4
2010-14 CHEVROLET CAMARO
1. Turn ignition to the ON position and shift vehicle into drive.
NOTE: In order to complete step 1 the battery must be connected. After completing
step 1, disconnect the negative battery cable and proceed to step 2.
2. Use a Panel-safe Removal Tool (PRT) to unclip Auxiliary gauge panel, unplug and remove.
3.
Use a small flathead screw driver, unclip screw cap located on the lower front side of the
shift knob.
4. Extract (1) T-20 Torx screw to remove gear shift knob.
5. Extract (4) 7mm screws securing shifter console, then with pick tool, unclip (1) clip located
on eachside under the shifter console, unplug and remove.
6. Use PRT to unclip each side panel from the center console.
7. Extract (1) Phillips head screw from each side located on the outer area of the center
console.
8. Extract (1) Phillips head screw from each side of center console’s rear panel, lift and pull
back to remove.
9. Extract (3) Phillips head screws behind center console’s armrest.
10. Extract (1) Phillips head screw in front of beverage holder.
11. Use PRT to unclip 12V and USB/3.5mm housing inside the armrest, unplug and remove.
12. Use PRT to unclip center console and remove.
13. Extract (2) 7mm screws securing radio panel located under and to the rear of A/C controls.
Use PRT to unclip radio fascia panel, unplug, and remove.
14. Extract (4) 7mm screws securing radio chassis / Drive assembly, unplug, lift away
and remove.
2
FACTORY STEREO REMOVAL
DASH MODIFICATION
BEFORE
AFTER
Use the illustrations labeled
BEFORE and AFTER for
modification location requirment.
Using a cutting tool, cut the area
as shown shaded/highlighted in
the BEFORE illustration of the
dash cavity so that it looks like
the AFTER.
Proceed to either the single DIN
assembly instruction on the next
page(3) or double DIN on page
4 after completing the dash
modification for the kit.
©2017 SCOSCHE INDUSTRIES, INC.
ITCGM01B 05/17
Product specificaties
| Merk: | Scosche |
| Categorie: | Niet gecategoriseerd |
| Model: | ITCGM01B |
Heb je hulp nodig?
Als je hulp nodig hebt met Scosche ITCGM01B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Scosche
7 Juni 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
2 Mei 2025
27 April 2025
19 Maart 2025
Handleiding Niet gecategoriseerd
- FALLER
- WOLF-Garten
- Katrin
- Ugreen
- Nature2
- Orbsmart
- Kaiser Nienhaus
- NEO Tools
- Chicco
- Celly
- Datacolor
- Bea-fon
- IsoAcoustics
- NetAlly
- McIntosh
Nieuwste handleidingen voor Niet gecategoriseerd
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025