Schwaiger ZHD01 Handleiding

Bekijk gratis de handleiding van Schwaiger ZHD01 (2 pagina’s), behorend tot de categorie Thermostaat. Deze gids werd als nuttig beoordeeld door 47 mensen en kreeg gemiddeld 4.5 sterren uit 4 reviews. Heb je een vraag over Schwaiger ZHD01 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

USER MANUAL ZHD01

TEMPERATURE SENSOR

ZHD01

MANUFACTURER INFORMATION

Dear Customer,

should you require technical advice and your

retailer could not help please contact our

technical support.

Schwaiger GmbH

Würzburger Straße 17 90579 Langenzenn

Hotline: +49 (0) 9101 702-199

www.schwaiger.de info@schwaiger.de

BDA_ZHD01

Business hours:

Monday to Thursday: 08:00 - 17:00

Friday: 08:00 - 14:30

HOME AUTOMATION

Congratulations and thank you for purchasing the Schwaiger ZHD01

product. Below you will find useful operating guidelines.

Display information

Display LEDExplanation

Room temperature displayed

Rapid green flashing

Red flashing

Flashes

Runs insertions or deletions

Red flashing every

150 seconds

Red flashing every

30 seconds

Insertions or deletions failed

Z-Wave information

General device classMulti-level sensor

Specific device classRouting multilevel sensor

Device typeRouting slave

SDK 4.55

NWI Yes

Explorer framesYes

Manufacturer ID0x0002

Product type ID0x0003

Product ID0x8010

Introduction

Schwaiger ZHD01 is a battery-operated temperature sensor. If it is integrated into the wireless

Z-Wave network, the control buttons can be used to control the heating system.

Disposal information

This device contains no batteries. It is an electrical device. It can be disposed of free of charge at

specified disposal sites.

EC Declaration of Conformity

„Hereby Schwaiger GmbH declares that the ZHD01 product is in compliance with the essential requi-

rements and other relevant provisions of Directive 1999/5/EC. “ The Declaration of Conformity can be

found at the following address: http://www.schwaiger.de/downloads

Installation

LED button

INCREASE temperature

Display

(with backlight)

LOWER temperature

1. Remove the back panel by

sliding it downwards.

3. Fasten the back panel to the wall.

2. Replace the batteries.

4. Gently push the Z-Wave RS on the back panel.

Z-Wave command classes

Command ClassVersionDescription

BASICV1• Basic SET: Not supported

• Basic GET: Multi-level sensor get

• Basic REPORT: Multi-level sensor report

(1 °C accuracy)

MANUFACTURER_

SPECIFIC

V2ID from Danfoss and Z-Wave RS

VERSIONV2Version of command classes, of the Z-Wave Library

and of Z-Wave RS

BATTERYV1Battery status

MULTI_CMDV1Conserve battery power by transmitting multiple com-

mands in a single package

WAKE_UPV2Switch-on intervals of 5 min to 24 h (default: 60

minutes)

PROTECTIONV20 = No protection

2 = User interface locked

CONFIGURATIONV2Specific Z-Wave RS configuration

SENSOR_MULTILEVELV6Specifies the value from the room temperature sensor

again

CENTRAL_SCENEV1By pressing the LED button the transmission of

CENTRAL_SCENE_ NOTIFICATION is triggered.

THERMOSTAT_

SETPOINT

V3When selecting a temperature setpoint on the display

controller, the setpoint is reported.

SCHEDULEV1When selecting a temperature and a number of hours

on the display controller reported the program change

values.

INDICATORV1Control of the LED display.

Paste in Z-Wave

• Make sure that Z-Wave RS is in the factory defaults setting.

• Activate „Inclusion/Paste“ on the Z-Wave controller.

• Press the LED button on Z-Wave RS.

• Check the process status on the controller and Z-Wave RS.

Product specificaties