Schneider MTN647091 Handleiding

Bekijk gratis de handleiding van Schneider MTN647091 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 16 mensen en kreeg gemiddeld 4.3 sterren uit 3 reviews. Heb je een vraag over Schneider MTN647091 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

V6470-561-02 11/21

MTN647091© Merten2009V6470-561-0211/21

The control unit 0-10 V REG-K/1-gang with manual

mode (refered to below as control unit) dims and

switches fluorescent lamps using electronic ballasts with

a 0-10 V/1-10 V interface and LV halogen lamps using

transformers with a 0-10 V/1-10 V interface.

|The control voltage range can be set with the ETS

via a parameter.

You can also manually switch the connected loads with

the manual switch on the control unit without bus volt-

age.

The control unit has a bus coupler. It is installed on a DIN

rail TH 35 according to EN 60715, with the bus connec-

tion made via a bus connecting terminal. A data rail is not

required.

SpaceLogic KNX Control unit 0-10 V

REG-K/1-gang with manual mode

Operating instructions

Art. no. MTN647091

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

•Connecting to installation networks

•Connecting several electrical devices

•Laying electric cables

•Connecting and establishing KNX networks

•Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

•Always operate the product in compliance with the

specified technical data.

•Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

Getting to know the control unit

en

ABus connecting terminal

BProgramming-LED (red)

CProgrammier button

DCable cover

EOperating-LED „RUN“ (green)

FManual switch

GChannel terminals for load voltage

HOutputs 1–10 V

1Set the control unit onto the DIN rail.

2Connect KNX.

¼WARNING

Risk of death from electric shock. The device

can become damaged.

Safety clearance must be guaranteed in accord-

ance with IEC 60664--1. There must be at least 4

mm between the individual cores of the 230 V

supply cable and the KNX line A.

¼WARNING

Risk of death from electric shock. The device

could become damaged.

Disconnect the mains voltage before connecting

the device to the load.

Terminals may not be inserted under load.

Connections, displays and operating

elements

Mounting the control unit

C

AB

E

F

G

H

D

1

2

1 2

34

5 mm

230 V

4 mm

A

¼DANGER

Risk of death from electric shock.

Voltage may be present at the outputs when the

mains voltage is connected to the system.

If subjected to strong vibrations during transpor-

tation, the switch contacts might change to the

enabled state.

After connecting the bus voltage, set the relays of

the channels to the position desired simply by

switching „On/Off“ or by changing the manual

switch to „OFF“.

3Connect the bus voltage.

4Connect the load.

5Connect the load voltage.

1Press the programming button.

The programming-LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The operation LED lights up: The application was loaded

successfully, the device is ready for operation.

AControl unit

BElectronic ballast with 0-10 V / 1-10 V inter-

face

CFluorescent lamp

DEletronic transformer with 0-10 V / 1-10 V con-

trol input

ELV halogen lamps

Fto other devices with 0-10 V / 1-10 V interface

Putting the control unit into operation

KNX

+ -

NL1

L

-

+

0-10V

0-10V

12V AC

A

-

+

L

N

-

+

L

N

F

D

B

0-10V

C

E

16 A

Product specificaties