Schneider MTN646991 Handleiding

Bekijk gratis de handleiding van Schneider MTN646991 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 14 mensen en kreeg gemiddeld 4.3 sterren uit 5 reviews. Heb je een vraag over Schneider MTN646991 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

The control unit 0-10 V REG-K/3-gang with manual

mode dims and switches fluorescent lamps using

electronic ballasts with a 0-10 V/1-10V interface and LV

halogen lamps using transformers with a 0-10 V/1-10 V

interface.

|The control voltage range can be set with the

ETS via a parameter.

You can also manually switch the connected loads with

the manual switches on the control unit without bus

voltage.

The control unit has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

•Connecting to installation networks

•Connecting several electrical devices

•Laying electric cables

•Connecting and establishing KNX networks

•Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

•Only operate the device according to the specifica-

tions stated in the Technical data.

•All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Control unit introduction

ABus connecting terminal

BCable cover

CProgramming button

DProgramming LED (red)

EOperating LED "RUN" (green)

FManual switch

GChannel terminals for load voltage

HOutputs 1-10V

1Set the control unit onto the DIN rail.

2Connect KNX.

¼WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Disconnect the mains voltage before connecting

the device to the load.

Terminals may not be inserted under load.

Connections, displays and operating

elements

Installing the control unit

1 23

B

E

A

C

D

F

H

G

2

1

3

5 mm

1 2

3 4

230 V

4 mm

KNX

3Connect the bus voltage.

4Connect the load.

5Connect the load voltage.

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

AControl unit

BElectronic ballast with 0-10 V/1-10V interface

CFluorescent lamp

DElectronic transformer with 0-10 V/1-10V

control input

ELV halogen lamps

FTo other devices with 0-10 V/1-10V interface

Putting the actuator into operation

KNX

+ -

NL1

L

-

+

0-10V

0-10V

12V AC

A

-

+

L

N

-

+

L

N

F

D

B

0-10V

C

E

16 A

SpaceLogic KNX Control unit 0-10 V REG-K/

3-gang with manual mode

Operating instructions

Art. no. MTN646991

en

123

V6469-562-01 11/21

Product specificaties