Saturn ST-FP1093 Handleiding

Saturn Vleesmolen ST-FP1093

Lees hieronder de 📖 handleiding in het Nederlandse voor Saturn ST-FP1093 (18 pagina's) in de categorie Vleesmolen. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18
ST-FP 1093
MEAT GRINDER
ЭЛЕКТРОМЯСОРУБКА
ЕЛЕКТРОМ´ЯСОРУБКА
GB
MEAT GRINDER
Dear Buyer!
We congratulate you on having
bought the device under trade name
“Saturn”. We are sure that our
devices will become faithful and
reliable assistance in your
housekeeping.
Avoid extreme temperature changes.
Rapid temperature change (e.g. when
the unit is moved from freezing
temperature to a warm room) may
cause condensation inside the unit and
a malfunction when it is switched on.
In this case leave the unit at room
temperature for at least 1.5 hours
before switching it on.
If the unit has been in transit, leave it
indoors for at least 1.5 hours before
starting operation.
Read this instruction manual carefully
before operating this unit.
Important Caution
Check each accessory carefully before
using this unit.
1. R e ad t h is m a n ual c a reful ly b ef ore
operating this unit.
2. This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction
co cerning use of the appliance by an
person responsible for their safety.
3. Children should be supervised to
ensure that they do not play with the
appliance.
4. Before using this unit, check the mains
power voltage corresponds to the
voltage shown on the marking plate.
5. Always remove the plug from the
power socket when this unit is not in
use and before carrying out any
cleaning or maintenance operation.
6. Never leave this unit unattended when
it is switched on. Keep this unit out of
the reach of the children.
7. Do not switch the appliance on if it
appears to be faulty in any way.
8. F o r r e p a i r s , a c c e s s o r i e s o r p o w e r c o r d
replacement, contact your dealer or an
authorized Service Center.
9. It is not allowed to immerse the base
into water for cleaning and it is
forbidden to start the unit or press the
control button by wet hands.
10. The water temperature should not be
over 60
0
C, when cleaning the unit.
11. Do not run this unit long-time,
otherwise the inner parts will be
damaged.
12. When the motor is running, do not
insert your finger or other objects into
the machine and container.
13. The instructions for food processors
and blenders shall warn of potential
injury from misuse. They shall state,
that care shall be taken when handing
the sharp cutting blades and during
cleaning.
14. Switch off the appliance and disconnect
from supply before changing
accessories or approaching parts that
move in use.
15. If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
Safety protection: The motor is
equipped with protective setting,
which will turn off the unit
automati dcally while overloa ing and
re-operate it after cooling.
Description of the appliance
Name of Parts
2
3
4
Preparing the meat grinder to work
and the actuation of the appliance
- Place the drive unit close to the power
network socket, on a firm surface so as not
to cover the ventilation holes within the
casing.
O mincing setperating the
Put the following elements into the mincing
chamber:
- Mincing screw with the coupling
towards the middle,
- Put the cutter knife on the mincing
screw end with the sharp edges facing
outside.
- mPut the screen so that the cha ber’s
protrusion enters the rut of the screen.
1. Tighten all the elements of the
mincing set – until home.
2. Put the assembled unit (1) onto the
drive unit (2) and turn into the
position, when you hear click of the
safety lock.
3. Put the food tray onto the mincing
chamber.
Using methods
- Put the meat around 300g (Suggest using
without bone and muscles of meat) onto
the food tray.
- Connect the power supply and turn on the
switch. After the normal operation of the
confirmation grinder, put the ready meat
into the chute feed tube.
- If food cannot be involved in the food
screw, p slowlylease use food pusher, -
2
push food. Do not use other alternative the
food pusher. Use reverse rotation function
in case of necessity.
- After use, please cut off the power supply.
Note: The process of chopper running, if
food card in the screw doesn’t work. should
immediately turn off the power.
Instruction for Use of Juicer extractor
Name of Parts
Operating the Juicer
- Place the juicer screw into the juicer
chamber. Insert the juicing strainer into the
chamber. Place the juicer screw cap onto
the drum end and turn it counter-clock-wise
until it clicks firmly into place.
- Connect assembled chamber set with
main body by turning lock clip clockwise
(about 60˚). Place hopper onto guide.
- juice drum under chamber set. PlugPlace
power cord into wall outlet.
- Press the switch. Place a few pieces of cut
fruit or vegetables, one at a time into the
guide. Use the food pusher to press the
fruit or vegetables gently down the guide.
Leave the machine on as you feed in the
fruit/vegetables.
Note:
1. Do not put your finger or other things
5


Product specificaties

Merk: Saturn
Categorie: Vleesmolen
Model: ST-FP1093

Heb je hulp nodig?

Als je hulp nodig hebt met Saturn ST-FP1093 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vleesmolen Saturn

Handleiding Vleesmolen

Nieuwste handleidingen voor Vleesmolen