Sanyo LNS-M02 Handleiding

Sanyo Projector accessoire LNS-M02

Bekijk gratis de handleiding van Sanyo LNS-M02 (6 pagina’s), behorend tot de categorie Projector accessoire. Deze gids werd als nuttig beoordeeld door 55 mensen en kreeg gemiddeld 4.5 sterren uit 28 reviews. Heb je een vraag over Sanyo LNS-M02 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/6

LCD PROJECTOR LENS

MODEL NO. LNS-S04/LNS-M02

LENS REPLACEMENT

AND INSTALLATION PROCEDURES

NOTES ON REPLACEMENT AND INSTALLATION

The procedures and the needed pars for lens installation depend on the type of

cabinet. Before installing or replacing the lens, make sure the type of cabinet and be

sure to refer to the Installations corresponding with your projector.

When installing or replacing the lens, make sure the Lens Model No. matches with

your projector. Refer to the catalog, or contact your sales dealer for the proper Lens

Model No.

TYPE OF THE CABINET AND INSTALLATION PROCEDURES

Refer to the Installation procedure corresponding to your projector and install the lens

correctly. (See the chart below.)

1AA6P1P5925-- (IFTT)

※ For use the other models (other than above cabinet), contact your sales dealer.

Printed in Japan

Some parts are not used for installation or replacement. Keep these parts for later use.

Note : Figures in this manual may be differ from the actual product.

After installing or replacing the lens, be sure to check the following for safety.

1. Check the lens is securely fixed.

2. Check no part is missing, or no mounting part is loose.

BE SURE TO CHECK FOR SAFETY

-1-

LIST OF CONTENTS

Following parts are included in the packing.

• LENS 1 pc.

• LENS CAP Front and rear (Each 1 pc.)

• SCREW DRIVER 1 pc.

• INSTALLATION MANUAL 1 pc.

Lens installation and replacement should be performed by the qualified

service personnel.

It should be followed by this procedure precisely.

Before attempt to replace the lens, confirm the model number (both the

LCD projector and the lens) and use the proper lens.

The lens cover is on the lens for protection. Be sure to remove the lens

cover before installation.

When installing or removing the lens, be careful not to stain, scratch or

damage the lens.

When shipping the projector with the lens, remove the lens before shipping

the projector.

If you have any questions, contact the dealers.

Notes on Lens Installation and Replacement

●

-2-

Turn the Lens Mount Cover counter-clockwise

and take it off by pulling forward. (See Fig. 1)

Fig. 1

Lens Mount Cover

Fig. 2

Remove 2 Screws and loosen 2 Screws . A B

Slide the Top Cover forward to take off.

(See Fig. 2)

Top Cover

Turn off the projector, press the Main On/Off

Switch to Off and unplug the AC power cord

from the AC outlet.

Remove the Cover Plate by lifting upwards.

(See Fig. 3)

Fig. 3

Cover Plate

This projector can use three (3) different types

of Light-Block Plates, use the Light-Block Plate

that corresponds to the appropriate optional

lens.

NOTE:

● The Light-Block Plate FK2A is separated to the

upper and lower plates.

Lower Plate

Upper Plate

DOWN

Insert the lower Light-Block Plate.

(See Fig. 4.)

Fig. 4

■LENS REPLACEMENT AND INSTALLATION PROCEDURE

NOTE:

●

Make sure the shape of the Light-Block Plate

is correct.

●

Make sure the mark (UP/DOWN and FRONT/

BACK) on Light-Block Plates are correct and

set them properly.

●

Use the following Light-Block Plate.

Light-Block Plate

Type FK2A

(610 337 0064)

Product specificaties

Merk:	Sanyo
Categorie:	Projector accessoire
Model:	LNS-M02
Kleur van het product:	Zwart
Gewicht:	3100 g
Diameter:	137 mm
Diafragma (F-F):	2.1 - 2.7
Brandpuntbereik:	125 - 162 mm
Zoomverhouding:	1.3x
Compatibiliteit:	PLC-HF10000L\nPLC-HF15000L\nPLC-XF1000\nPLC-XF47\nPLC-XF47A