Sanus SF34 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Sanus SF34 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
Customer Service: (800) 359-5520 • (651) 484-7988 info@sanus.com
Customer Service Europe: + 31 40 2324700 europe.sanus@milestone.com
(6901-300165 <01>)
ESPAÑOL FRANÇAIS РУССКИЙ 中文
ENGLISH
International Instruction Manual For Steel Foundations®
SF22 and SF26
SF30 and SF34
ENGLISH
Page 2
Hardware List
(PHOTO 1)
A) isolation block - 2
B) 1-1/2" pan head bolt - 4
C) lock washer - 4
D) rubber isolation pad - 16
E) plastic foot - 8
F) 5/8" pan head bolt - 8
G) carpet spike - 8
H) machine nut - 16
I) allen key - 2
J) speaker stud - 8
K) 5/8" speaker bolts (2)
(For Boston Acoustics VRM series
and other bolt–mount speakers.)
L) cork damping washer - 4
M) wire guide - 4
N) atheadbolt-4
ab
c
d
eg
PHOTO 1
Important: This product uses two
different feet for each base. Before
installing, be sure to check that the
feet are mounted with the (1) foot
on the front left and rear right of
the base, (2) front right and rear
left. The designation (1) & (2) are
on the bottom of each foot.
h
k
i
j
l
m
n
f
ENGLISH
Page 3 * PLEASE READ THE NOTE ON PAGE OF THIS MANUAL!5
‘Take the time to find the right speaker locations for your
listening room.
1] Attach the plastic feet (e) to the corners of
the base with the small pan head bolts (f). Photo
2-Group two pillars with each base. Align the
holes in the base with the holes in the isolation
block (a). Bolt the pillars and the base together
with the isolation block between them using
the large pan head bolts (b) and lock washers
(c). Photo 3-Using the wire guide is optional.
2] Adhere the two inch self-adhesive damping washers (l) to the flush side of each
top plate. The damping washers will be set in between the top plate and the pillars.
(Optional: You may fill the pillars with sand or shot at this time.) Align the holes in
the top plate with corresponding holes in the top of each pillar. Bolt the pillars and
the top plate together using the flat head bolts (n). Photo 4-The wire guide (m) is
optional.
3] Both spiked feet (g) and rubber feet (d) are provided for your Steel Foundations
®.
The spiked feet are preferable in terms of performance. Thread a machine nut (h)
over the spiked feet and thread the ends of the spiked feet into the threaded inserts
in the corner feet. Adjust the spiked feet until the stand is level and then lock into
place by tightening the machine nut. Use of
the spiked feet is optional.* The rubber feet
are provided as an alternative.
4] Three forms of speaker mounts are pro-
vided, steel speaker studs (j), rubber pads (d)
and the new Foundation Mount™ (k) which
is discussed in the next section. To utilize the
steel speaker studs, thread them into the holes
in the corners of the top plates until the end Photo 3
Photo 2


Product specificaties

Merk: Sanus
Categorie: Niet gecategoriseerd
Model: SF34

Heb je hulp nodig?

Als je hulp nodig hebt met Sanus SF34 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Sanus

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd