Samsung PN43D440 Handleiding

Samsung Televisie PN43D440

Lees hieronder de 📖 handleiding in het Nederlandse voor Samsung PN43D440 (3 pagina's) in de categorie Televisie. Deze handleiding was nuttig voor 91 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

: Install the Stand

Follow the steps below to connect the TV to the stand.

✎

NOTE

Make sure to distinguish between the front and back of the Stand and

Guide Stand when assembling them.

Make sure that at least two people lift and move the PDP TV.

1 With your TV upright, connect the

TV to the Stand.

2 Fasten four screws (M4 X L8) at

position.

: Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1. Lift the cover on the back of the remote upward as shown in the ﬁgure to the

right.

2. Install two AAA batteries.

✎

Make sure to match the +

and - ends of the batteries

to the diagram in the battery

compartment.

3. Replace the cover.

: Connect Power and Antenna or Cable

VHF/UHF Antenna

Connect Ant In to

• Wall cable jack

• VHF/UHF Antenna

• Cable or Satellite box

Ant or Cable Out

Make sure the AC power cord is plugged in securely to

the wall outlet and the TV.

Use a 75 ohm (round) cable.

Antenna Cable

(Not Supplied)

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.

Read this setup guide to get your TV up and running quickly.

1-800-SAMSUNG (1-800-726-7864)

Samsung Electronics America, Inc.

85 Challenger Road Ridgeﬁeld Park, NJ 07660-2112

Samsung Electronics Canada Inc.

55 Standish Court Mississauga, Ontario L5R 4B2

Call Center hours of operation: Mon-Sun, 9:00 AM -12

AM EST.

To register this product, visit: www.samsung.com/

STOP

Please do not return this unit.

If you have problems operating your

TV, call:

1-800-SAMSUNG (1-800-726-7864)

For web support please visit:

www.samsung.com/support

: Connect External Devices

Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)

: Run Plug & Play

When you turn on your TV for the ﬁrst time, it automatically launches the Plug &

Play function. With Plug & Play, you can select the On Screen Display language, set

the clock mode, and launch the TV’s channel memorizing process.

It also displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow

buttons on your remote. To make a selection, press the ENTER

button.

To skip a screen, press the button. To turn on your TV, press the MENU POWER

button on the remote or on the TV. To run Plug & Play, follow these steps:

1 Using your remote control, select

the language for the On Screen

Display (OSD), and then press

the ENTER

button.

2 Select , and then Home Use

press the ENTER

button. If

you select , the TV Store Demo

will reset your picture and audio

settings every 30 minutes.

3 Select the Antenna source

to memorize, you must select

Antenna Source to same type

as your cable system type. After

selecting source, select ; Start

then press the ENTER

button

on your remote.

✎

Most cable systems are Standard(STD) systems, If you are not sure about

what kind of cable system you have, contact your cable company.

✎

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After

Plug & Play is complete, set your TV to Channel 3 or 4, according to the

directions for your cable or satellite box.

4 The TV memorizes the available

channels. This process can take

up to 45 minutes.

5 After the TV has memorized the

channels, choose the Clock

Mode Auto. Select if you have

a digital channel in your area.

Select if you don’t, or Manual

if you have a cable or satellite

box. When done, press the

ENTER

button.

✎

If you select Manual, the

clock setting screen appears.

6 Select the daylight savings time

setting: or and then Off, On Auto

press the ENTER

button.

✎

This function is only available

when the is set to Clock Mode

Auto.

7 Select the time zone in which you live, and then press the ENTER

button.

8 After the time zone screen, The connection method for best HD screen

quality is displayed. Press Right arrow button on your remote to view each

screen in succession. Press the Blue button to skip this section.

9 The Enjoy your TV. screen appears. Then press the ENTER

button.

If You Want to Rerun Plug & Play

1. Press the SOURCE button on your remote, then select mode.TV

2. Press the MENU button on your remote to display the menu.

3. SetupPress the or button to select ▲ ▼ , and then press the ENTER

button.

4. Press the ENTER

again to select .Plug & Play

Connecting an audio device (Home Theater, etc.)

Connect your TV to your Home Theater or other audio device to enjoy enhanced

Sound quality.

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

HDMI IN 3

HDMI OUT

AUDIO OUT

VIDEO OUT

AUDIO OUT

COMPONENT OUT

AUDIO OUT

DVI OUT

Using an HDMI to DVI Cable

HD connection (up to 720p/1080i)

Very Good Connection

Device

Best Connection

HD connection (up to 720p/1080i)

Using an HDMI Cable

DVD, Blu-ray player, HD cable box, HD STB

(Set-Top-Box) satellite receiver

Device

Using a Component Cable

Good Connection

Component connection (up to 720p/1080i)

DVD, Blu-ray player, cable box,

STB satellite receiver, VCR,

Device

Use one of the connections below to connect your TV to an external A/V device. We recommend using

HDMI for the highest picture quality.

✎

When connecting to AV IN on the back of your TV, attach the video cable (yellow) to the green jack

next to the label. The jack will not match the color of the video cable (yellow).AV IN

Move

Enter

Select Language of the OSD.

Language :

Plug & Play

English

Español

Français

Move

Enter

Select ‘Home Use’ when installing this TV in your home.

Store Demo Home Use

Plug & Play

Move

Enter

Skip

Select the Antenna source to memorize.

Air

Cable

Auto

Start

Plug & Play

Move

Enter

Skip

Set the Clock Mode.

Clock Mode Auto

Manual

Plug & Play

Move

Enter

Skip

Set to daylight saving time.

DST

Off

Auto

Plug & Play

48%

Enter

Skip

Auto Program in Progress.

DTV Air : -- Air : --

DTV Cable : -- Cable : -- Cable : 35

Stop

Plug & Play

BN68-03859A-00

Lowest Quality Connection

Using an Audio/Video Cable

Audio/Video connection (480i only)

DVD, Blu-ray player, cable box, STB satellite

receiver, VCR

Device

HDMI Cable (Not Supplied)

HDMI to DVI Cable

(Not Supplied)

Audio Cable (Not Supplied)

Audio Cable

(Not Supplied) Component Cable

(Not Supplied)

Video Cable

(Not Supplied)

OPTICAL

PTI

OPTICAL

Digital Audio connection

Digital Audio System

Using an Optical Cable

Optical Cable (Not Supplied)

DVI OUT

AUDIO OUT

HD connection

Using an HDMI to DVI Cable

HDMI to DVI Cable (Not Supplied)

Audio Cable (Not Supplied)

(M4 X L8)

(Correct assembly) (Incorret assembly)

: Remote Control

Remote Control Buttons and Functions

Selecting a Source

To watch a movie on your Blu-ray player or watch

your favorite TV show, you must select the correct

source. A source is a device, such as a Blu-ray/DVD

player, a cable/satellite box, antenna or a cable TV

input. Sources can be connected to your TV through

the HDMI, DVI, Component, Composite, or D-sub

connections, or through the Antenna or Cable In connections.

To view the signal from a source connected to the HDMI, DVI, Component,

Composite, or D-sub jack, press the button on your remote. Each time SOURCE

you press the button, you change to a different source.SOURCE

Viewing the On Screen Menus

To view the On Screen Menus, follow these steps:

1. With the power on, press the MENU button on

your remote. The main menu appears.

The menu’s left side has the following menu

options: and Picture, Sound, Channel, Setup, Input, Application Support.

2. Press the or button on your remote to select a menu option, and then ▲ ▼

press the ENTER

button.

3. When done using the menu, press the EXIT button on your remote to exit.

Changing the Picture Mode

Your TV has three preset Picture Modes with factory adjusted settings, each

designed to give you an excellent picture under speciﬁc conditions.

To change the mode, press the Picture P.MODE button on your remote. The ﬁrst

time you press it, your TV displays the current setting. Thereafter, each time you

press the P.MODE button, you change the mode of the picture on the screen.

The Modes are listed and described in the table below:Picture

Mode Description

Dynamic Brightens picture. For a vibrant, enhanced image in brightly lit or

sunny room.

Standard For a bright, detailed picture in a normally lit room.

Movie For a studio quality cinema picture in a dimly lit or dark room.

To change the , follow these steps:Picture Mode

1. PictureWith the TV on, Press the MENU button on your remote, then select .

2. ModeSelect , then Press the ENTER

button.

3. Mode PictureOn the menu in , use the or on your remote to select the ▼ ▲

picture mode you want.

4. Press the ENTER

button to ﬁnish the change.

Changing the Screen Size

Your TV has several screen size options, each designed to work best with speciﬁc

types of video input. If you have a cable box or satellite receiver, it may have its own

set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The ﬁrst time

you press it, your TV displays the current setting. Thereafter, each time you press

the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

16:9 4:3 Wide screen Standard screen Wide Fit

Zoom 1 Zoom 2 Screen Fit

✎

Screen Fit: Displays the full image without any cut-off when HDMI (720p /

1080i / 1080p) or Component (1080i / 1080p) signals are inputted.

Changing Channels and Adjusting the Volume

Adjust the volume by pressing the Volume button

on the remote. Change the channels by pressing the Channel button on the remote.

✎

If your TV is attached to a cable or satellite box, change the channel using

the box’s remote.

✎

You can also change the channels by pressing the

button on the front panel of your TV and adjust the volume by pressing the y button.

Connecting a USB Device for Media Play

You can enjoy photo and music

ﬁles stored on a USB device

by connecting it to the TV and

using the feature. Media Play

To connect a USB device

for , follow these Media Play

steps:

1. Turn on your TV.

2. Connect a USB device

containing photo and/or music ﬁles to the jack on the side of the TV.USB

3. InputWhen the selection screen is displayed, press the button to select 

Media Play (USB), then press the ENTER

button.

SLEEP

P.SIZE

A B C D

MEDIA.P

Turns the TV on and off.

Returns to the previous channel.

Cuts off the sound temporarily.

Changes channels.

Displays Favorite Channel Lists on the screen.

Displays the channel list on the screen.

Displays information on the TV screen.

Selects the on-screen menu items and changes the values

seen on the menu.

Exits the menu.

MTS: Press to choose stereo, mono or Separate Audio

Program (SAP broadcast).

P.SIZE: Selects the picture size.

CC: Controls the caption decoder.

Press to directly access channels.

Press to select additional channels (digital) being

broadcasted by the same station. For example, to select

channel “54-3”, press “54”, then press “-” and “3”.

Adjusts the volume.

Brings up the OSD.

Displays .Media Play (USB)

Quickly select frequently used functions.

Returns to the previous menu.

Buttons used in the Channel list, Media Play (USB)

menu, etc.

Displays and selects the available video sources.

Photo

Photo Music Setup

SUM

307.2MB/973.7MB

Move

Enter

Return

Free

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the

clock, follow these steps:

1. Turn on your TV, press the button on your remote, then select MENU Setup →

Time.

2. Clock ModeSelect , and then press the ENTER

button.

3. Auto ManualChoose or .

If you select , the current time will be set automatically using the time Auto

from a digital channel.

If you select Manual, you can set the Month, Day, Year, Hour, Minute

and directly by pressing up, down, left and right arrow button on am/pm

your remote.

4. Press the RETURN button on your remote when done.

•Caution

The glass screen of your PDP TV can break if you accidently drop the TV. Handle the TV with care.

When moving the TV, always have two or more people pick it up and carry it as a safety precaution. Do not lay the TV ﬂat on its face or back.

(Your) Samsung Plasma TV is a high quality television that has been carefully packaged to protect the integrity of its glass panel and component parts during shipment.

It is, nonetheless, a fragile piece of electronics that requires careful handling. Refrain from putting undue stress on any part of the packaging when shipping or unpacking

the TV. Use care when installing the TV. Avoid placing the TV in a location where it may be struck, exposed to sharp impacts, or fall. Panel breakage caused by a fall or

impact strike is not covered under the manufacturer’s warranty.

•The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using the cloth provided or a soft

cloth to prevent scratches.