Salton BS20 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Salton BS20 (6 pagina's) in de categorie Vacuumverpakker. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
VACUUM BAG
SEALER
Model: BS-20
POSITION ONLY
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electrical hazards, do not immerse cord, plugs, or the
appliance in water or other liquid.
4.
Close supervision is necessary when any appliance is used by or near children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to Salton for examination, repair or adjustment. See Warranty.
7. The use of accessories or attachments not recommended by Salton may
cause hazards.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Prior to connecting or disconnecting plug from wall outlet, turn any
control to "off".
12. This appliance is for Household Use Only. Do not use appliance for other
than its intended use.
13. Do not leave unit unattended while in use.
2
SAVE THESE INSTRUCTIONS
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not modify the plug in any way.
DESCRIPTION OF PARTS
1. Cover
2. Sealing Wire
3. Suction Nozzle
4. Polyethylene Roll
(Polyethylene Film)
5. Indicator Light
HOW TO USE
Make the Bag
1. Place the unit on a flat, level surface and plug into a 120 volt outlet.
2. Lift the cover and place the Polyethylene Roll so that it unwinds from the
bottom of the Roll.
3. When starting a new Roll, pull the Polyethylene Film about 1/2" (1.25 cm)
over the Sealing Wire and make sure that the Polyethylene Film lies
smoothly.
4. Close the Cover and make a seal on the Film by pressing down both
areas that are marked ‘sealing’ on the right and left hand corners of the
Cover. The Indicator Light will go on and remain on for 10 seconds.
DO NOT SEAL LONGER THAN 10 SECONDS. When the Indicator Light
goes out release pressure on Cover. NOTE: The sealing time can be
shortened by simply lifting the Cover.
5. Lift the Cover. Remove excess 1/2 " (1.25cm) of Polyethylene Film. Unroll
Polyethylene Film to the desired bag width and seal again.(Follow directions
in #4 above) This will simultaneously create the first seam for the next bag
and separate the current bag from the rest of the Roll.
NOTE: DO NOT MAKE THE BAG LONGER THAN 11" (27.5 cm)
AS YOU WILL NOT BE ABLE TO SEAL THE TOP OF THE BAG.
3
2
1
3
4
5


Product specificaties

Merk: Salton
Categorie: Vacuumverpakker
Model: BS20

Heb je hulp nodig?

Als je hulp nodig hebt met Salton BS20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vacuumverpakker Salton

Salton

Salton BS20 Handleiding

8 December 2022

Handleiding Vacuumverpakker

Nieuwste handleidingen voor Vacuumverpakker