Ryobi R18XLTR24 Handleiding

Ryobi Niet gecategoriseerd R18XLTR24

Lees hieronder de 📖 handleiding in het Nederlandse voor Ryobi R18XLTR24 (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 70 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16

R18XLTR20

Original Instructions

IMPORTANT!

It is essential that you read the instructions in this manual

before assembling, operating, and maintaining the

product.

Subject to technical modication.

Safety, performance, and dependability have been given top

priority in the design of your cordless line trimmer or edge

trimmer.

INTENDED USE

The cordless line trimmer or edge trimmer is intended to

be used only by adults who have read and understood

the instructions and warnings in this manual and can be

considered responsible for their actions.

The product is intended only for outdoor use in a well-

ventilated area. For safety reasons, the product must be

adequately controlled by a two-handed operation.

When tted with the line trimmer head (and appropriate

guard), the product is intended for cutting long grass, pulpy

weed, and similar vegetation at or about ground level. The

cutting plane should be approximately parallel to the ground

surface.

The cutting plane should be approximately parallel to the

ground surface when trimming and approximately vertical

when edging.

The product should not be used to cut or trim hedges,

bushes, or other vegetation where the cutting plane is not

parallel to the ground surface.

Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and instructions

may result in electric shock, re, and /or serious injury.

■When using the product, the safety rules must be

followed. For your safety and that of bystanders, read

these instructions before operating the product. Keep

the instructions safe for later use.

■The product is not intended to be used by children or

persons with reduced physical, mental, or sensory

capabilities. Children should be adequately supervised

to ensure that they do not play with the product.

■Some regions have regulations that restrict the use of

the product. Check with your local authority for advice.

TRAINING

■Read the instructions carefully. Be familiar with all

controls and the proper use of the product.

■Never allow children or people who are unfamiliar with

these instructions to use the product. Local regulations

may restrict the age of the operator.

■Keep bystanders, children, and pets 15 m away from the

area of operation. Turn off the product if anyone enters

the area.

■Never use the product while tired, ill, or under the

influence of alcohol, drugs, or medication.

■Keep in mind that the operator or user is responsible for

accidents or hazards occurring to other people or their

property.

PREPARATION

■Wear full eye and hearing protection while operating the

product. If working in an area where there is a risk of

falling objects, head protection must be worn.

■Hearing protection may restrict the operator’s ability

to hear warning sounds. Pay particular attention to

potential hazards around and inside the working area.

■Wear heavy, long trousers, boots, and gloves. Do not

wear loose-fitting clothing, short trousers, or jewellery of

any kind. Do not use the product with bare feet.

■Secure long hair so that it is above shoulder level to

prevent entanglement in moving parts.

■Before use and after any impact, check that there are no

damaged parts on the product. A defective switch or any

part that is damaged or worn should be properly repaired

or replaced by an authorised service centre.

■Make sure that the cutting attachment is properly

installed and securely fastened.

■Never operate the product unless all guards, deflectors,

and handles are properly and securely attached.

■Consider the environment in which you are working.

Keep the working area free from wires, sticks, stones,

and debris, which if struck by the cutter, can become

thrown objects.

BATTERY TOOL USE AND CARE

■Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with

another battery pack.

■Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk

of injury and fire.

■When the battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

■Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

LINE TRIMMER SAFETY WARNINGS

■Never allow children, persons with reduced physical,

sensory, or mental capabilities, or lack of experience

and knowledge, or people who are unfamiliar with the

instructions to use the product.

■Use the product in daylight or with good artificial light.

■Avoid using the product on wet grass.

■Keep firm footing and balance at all times, and be sure

of proper footing on slopes.

■Do not walk backwards when using the product. Walk,

never run.

■Keep the head attachment below waist level.

■Never use the product with damaged guards or without

guards in place.

■Never fit a metal replacement line.

■Keep hands and feet away from the cutting means at all

times, especially when turning on the motor.

Original Instructions

■Beware, the cutting elements continue to rotate after the

motor is turned off.

■Beware of objects thrown by the cutting means. Clear

debris like small stones, gravel, and other foreign objects

from the work area before starting the operation. Wires

or string may become entangled with the cutting means.

■To reduce the risk of injury associated with contacting

moving parts, always turn off the product, remove the

battery pack, and allow both to cool down. Make sure

that all moving parts have come to a complete stop:

●before servicing

●before clearing a blockage

●before checking, cleaning, and working on the

product

●before changing accessories

●after striking a foreign object

●whenever leaving the product unattended

●whenever performing maintenance

●whenever the product starts to vibrate abnormally

■Wear full eye and hearing protection while operating the

product. If working in an area where there is a risk of

falling objects, head protection must be worn.

■Hearing protection may restrict the operator’s ability

to hear warning sounds. Pay particular attention to

potential hazards around and inside the working area.

■Wear heavy, long trousers, boots, and gloves. Do not

wear loose-fitting clothing, short trousers, or jewellery of

any kind. Do not use the product with bare feet.

■Secure long hair so that it is above shoulder level to

prevent entanglement in moving parts.

■The small blade fitted to the lawn guard is designed to

trim the newly extended line to the correct length for safe

and optimum performance. The blade is very sharp.

Do not touch the blade, particularly when cleaning the

product.

■Always ensure that ventilation openings are kept clear

of debris.

■Before use and after any impact, check that there are no

damaged parts on the product. A defective switch or any

part that is damaged or worn should be properly repaired

or replaced by an authorised service centre.

■Make sure that the cutting head attachment is properly

installed and securely fastened.

■Make sure that all guards, deflectors, and handles are

properly and securely attached.

■Do not modify the product in any way. This may increase

the risk of injury to yourself or others.

■Use only the manufacturer’s replacement cutting line.

Do not use any other cutting attachment.

■Immediately turn off the product and remove the battery

pack in the event of an accident or breakdown. Do not

operate the product again until it has been fully checked

by an authorised service centre.

■Ensure that the line cut-off blade in the guard is properly

positioned and secured before each use.

ADDITIONAL BATTERY SAFETY WARNINGS

To reduce the risk of re, personal injury, and product

damage due to a short circuit, never immerse the product,

battery pack, or charger in uid or allow uid to ow inside

them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing

products, etc., can cause a short circuit.

TRANSPORTATION AND STORAGE

■Turn off the product, remove the battery pack, and allow

both to cool down before storing or transporting.

■Remove all foreign materials from the product.

■Do not store or transport the product with the battery

pack fitted. Remove the battery pack, and secure it

separately. Store the product in a cool, dry, and well-

ventilated place that is inaccessible to children. Keep

the product away from corrosive agents, such as garden

chemicals and de-icing salts. Do not store the product

outdoors.

■For transportation in vehicles, secure the product

against movement or falling to prevent injury to persons

or damage to the product.

TRANSPORTING LITHIUM BATTERIES

■Transport the battery pack in accordance with local and

national provisions and regulations.

■Follow all special requirements on packaging and

labelling when transporting batteries by a third party.

Ensure that no batteries can come in contact with other

batteries or conductive materials while in transport

by protecting exposed connectors with insulating,

nonconductive caps or tape. Do not transport batteries

that are cracked or leaking. Check with the forwarding

company for further advice.

MAINTENANCE

■Use only original manufacturer’s replacement parts,

accessories, and attachments. Failure to do so can cause

possible injury, can contribute to poor performance, and

may void your warranty.

■Servicing requires extreme care and knowledge

and should be performed only by a qualified service

technician. Have the product serviced by an authorised

service centre only.

■Turn off the product and remove the battery back before

conducting any maintenance or cleaning work.

■You may make adjustments or repairs described in this

manual. For other repairs, contact an authorised service

centre.

■For the replacement line, use only a nylon filament line

of the diameter described in the specifications table of

this manual.

■After each use, clean the product with a soft, dry cloth.

Any part that is damaged should be properly repaired or

replaced by an authorised service centre.

■Check all nuts, bolts, and screws before each use and

at frequent intervals for proper tightness to ensure that

the product is in safe working condition. Any part that is

damaged should be properly repaired or replaced by an

authorised service centre.

■Bring the product to an authorised service centre to

replace damaged or unreadable labels.

■Injuries may be caused, or aggravated, by prolonged

use of a tool. When using any tool for prolonged periods,

ensure that you take regular breaks.

Product specificaties

Merk:	Ryobi
Categorie:	Niet gecategoriseerd
Model:	R18XLTR24

Heb je hulp nodig?

Als je hulp nodig hebt met Ryobi R18XLTR24 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Ryobi

Ryobi One+ RY18BI150B Handleiding

17 Juli 2023

Ryobi RC18640 Handleiding

22 Juni 2023

Ryobi CR120 Handleiding

17 Juni 2023

Ryobi RSH2445B Handleiding

9 Juni 2023

Ryobi One+ R18PDID2 Handleiding

22 Mei 2023

Ryobi RY18BLA Handleiding

19 Mei 2023

Ryobi RPN780 Handleiding

6 Mei 2023

Ryobi RLT36BS Handleiding

20 April 2023

Ryobi RBCLLG1 Handleiding

18 April 2023

Ryobi One+ R18CK3D Handleiding

16 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024