Russound BSK-2 Handleiding

Bekijk gratis de handleiding van Russound BSK-2 (21 pagina’s), behorend tot de categorie Hifi systeem. Deze gids werd als nuttig beoordeeld door 56 mensen en kreeg gemiddeld 4.1 sterren uit 6 reviews. Heb je een vraag over Russound BSK-2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

IMPORTANT

PLEASE

READ THIS

IF

USING MORE

THAN

ONE

BSK-2 KIT WITH

A RUSSOUND

MCA-66

OR

MCA-88

CONTROLLER

In

order

to

have

more

than

one

BSK-2

kit

on

the

Russound controller's RNET

communication

bus, each BTC-2

must

be

properly

paired

to

its BTC-2X BEFORE

being

connected

to

the

Russound controller.

Attempting

to

use

more

than

one

BTC-2

without

completing

this

simple

pairing

process will result in all

unpaired

BTC-2's

not

switching

inputs

properly

when

the

BTC-2X

stops

receiving a

Bluetooth

audio

signal.

This

only

occurs

if

using

more

than

one

BSK-2

kit

with

a Russound controller.

If

you

are

NOT

using

your

BSK-2

kit

with

a Russound

controller

or

if

you are

only

using a single BSK-2

kit

with

your

Russound controller, you

don't

need

to

perform

any

of

these steps and can

proceed

with

the

installation

following

the

instructions in

the

included

manual.

To

pair

each

set

of

BTC-2 and BTC-2X

together

for

use

with

a Russound

controller:

1)

With

the

BTC-2X and BSK-2 disconnected

from

power, use a flathead screwdriver

to

set

the

source

number

on

the

bottom

of

the

BTC-2X

to

the

source

number

that

matches

the

controller's configured source

number

for

this BTC-2X

2)

Connect

your CATS cable

from

the

BTC-2

to

the

BTC-2X.

DO

NOT

CONNECT

the

RNET connection

from

the

BTC-2

to

the

controller yet.

3)

Apply

power

to

the

BTC-2.

4)

Press and

hold

the

"Pair"

button

on

the

rear

of

the

BTC-2X

for

5 seconds until

the

LED

blinks green twice. That completes

the

pairing

of

the

BTC-2X

to

its BTC-2.

5)

Connect

one

of

the

BTC-2's available RNET

ports

to

one

of

the

MCA-66

or

MCA-88

controller's available RNET

ports

or

to

an available RNET

port

on

another

BTC-2

that

is

already connected

to

one

of

the

controller's RNET ports.

Press and hold the

BTC-ZX pair button

for

5 seconds

until

the

LED blinks

GREEN@

~

Make sure

to

set

your

BTC-2X

source

number

dial

first

CATS

USB

-

S.,pply

MCA-BB

or

MCA-66

Make sure

that

no cables

are

connected

to

the

ANET

ports

while

performing

these

steps."

C2022 Russound/FMP, Inc. All rights reserved. All trademarks are property

of

their respective owners. Specifications are subject

to

change without notice. Russound is

not

responsible for typographical errors or omissions.

Product specificaties