Russell Hobbs 15066 therma select Handleiding

Russell Hobbs Waterkoker 15066 therma select

Lees hieronder de 📖 handleiding in het Nederlandse voor Russell Hobbs 15066 therma select (90 pagina's) in de categorie Waterkoker. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/90
instructions 2
Bedienungsanleitung 6
mode d’emploi 10
instructies 14
istruzioni per l’uso 18
instrucciones 22
instruções 26
brugsanvisning 30
bruksanvisning 34
instruksjoner 38
ohjeet 42
инструкции (Русский) 46
pokyny 50
inštrukcie 54
instrukcja 58
uputstva 62
navodila 66
οδηγίες 70
utasítások 74
talimatlar 78
instrucţiuni 82
инструкции ългарски) 86
2
Read the instructions and keep them safe. If you pass the appliance on, pass on the instructions
too. Remove all packaging, but keep it till you know the appliance works.
important safeguards
Follow basic safety precautions, including:
1 This appliance must only be used by or under the supervision of a responsible adult. Use and
store the appliance out of reach of children.
2 Don’t put the kettle, stand, cable, or plug in any liquid; don’t use the kettle in a
bathroom, near water, or outdoors.
3 Don’t touch hot surfaces.
4 Put the stand on a stable, level surface.
5 Keep the kettle, stand, and cable away from the edges of worktops and out of reach of
children.
6 Route the cable so it doesn’t overhang, and can’t be tripped over or caught.
7 Wind excess cable beneath the stand.
8 Unplug the stand when not in use, before moving and before cleaning.
9 Don’t use the kettle for any purpose other than heating water.
10 This appliance must not be operated by an external timer or remote control system.
11 Use the kettle only with the stand supplied (and vice versa).
12 Don’t use the appliance if it’s damaged or malfunctions.
13 If the cable is damaged, it must be replaced by the manufacturer, its service agent, or
someone similarly qualified, in order to avoid hazard.
household use only
before using for the first time
Fill to max, boil, discard the water, then rinse. Do this three times, to remove manufacturing dust,
etc.
filling
1 Remove the kettle from the stand.
2 Press the lid release button to open the lid.
3 Fill with at least 2 cups of water, but not above max.
4 If you overfill, the kettle may spit boiling water.
5 Close the lid, and press down to lock it.
3
6 Check the lid is closed, or the kettle won’t switch off when it boils.
switching on
7 Plug the stand into the wall socket.
8 Put the kettle on the stand – take care not to spill.
9 Press and release the 2 button. “100” will flash on the display.
10 The kettle will start to heat up.
boil
11 If you want to boil the water, do nothing.
12 When the water boils, the element will switch off, and the display will stop flashing.
13 After about a minute, the display will switch off.
variable temperature
14 If you want to heat the water to a different temperature, use the - and + buttons to change
the display from 100 (boil) to the temperature you want.
15 The temperatures available are: 100 (boil), 95, 90, 85, 80, 75, 70, 65, 60, 55, 50, 45, and 40 (that’s
°C).
16 The display will flash while the water is heating, then stop flashing to show that it has reached
the set temperature.
17 After about a minute, the display will switch off.
changing temperature
18 When the kettle has reached the set temperature, you can’t reduce the temperature setting
on the display till the water has cooled down.
19 If you get the temperature wrong, and want to change it:
either pour the hot water away, and refill with cold water
or wait till the kettle cools down (it’ll cool a bit faster if you open the lid)
keep warm
20 If you want the kettle to keep the water at the set temperature, press and release the 9
button.
, This function only works at the 90, 85, 80, 75, 70, 65, 60, 55, 50, 45, and 40 settings.
21 A dot will appear on the bottom right of the display to show that the keep warm function is
operating.
22 The element will switch on intermittently, to keep the water hot.
23 When it’s heating, the display will flash. The flashing will stop when the water again reaches
the set temperature.
25 After about an hour, the appliance will switch itself off.
25 To switch it on again, press 2.
26 To cancel the keep warm function, press and release the 9 button again – the dot will
disappear.
, Keep an eye on the water level – don’t let the level get below 2 cups.
switching off
27 To switch off manually, press 2.
28 This will switch off the element and the display, and put the kettle into standby mode.
29 To save electricity, unplug the stand.
instructions
drawings
1 hooks
2 filter (rear)
3 hook
4 holes (inside spout)
5 lid
6 lid release button
7 spout
8 handle
9 water level window
10 connectors
11 stand
12 display


Product specificaties

Merk: Russell Hobbs
Categorie: Waterkoker
Model: 15066 therma select

Heb je hulp nodig?

Als je hulp nodig hebt met Russell Hobbs 15066 therma select stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Waterkoker Russell Hobbs

Handleiding Waterkoker

Nieuwste handleidingen voor Waterkoker