Rossmax SB220 Handleiding
Rossmax
Hartslagmeter
SB220
Lees hieronder de 📖 handleiding in het Nederlandse voor Rossmax SB220 (2 pagina's) in de categorie Hartslagmeter. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Cleaning
Maintenance
Troubleshooting
Specification
1. Please clean the surface of the device before using.
Wipe the device with medical alcohol (70% isopro-
pyl alcohol)first, and then let it dry in air or clean it
by dry clean fabric. When cleaning the device with
water, the water temperature should be lower than
60°C
2. Using the medical alcohol to disinfect the product
after use, prevent from cross infection for next time
use.
3. The best storage environment of the device is - 25°C
to 70°C ambient temperature and not higher than
90% relative humidity.
Note:
1. Do not sterilize, autoclave or immerse this device
in liquid. Do not pour or spray any liquids onto the
device.
2. Do not use caustic or abrasive cleaning agents, or
any cleaning agent containing ammonium chloride
or isopropyl alcohol.
Recommends user to return this device to the man-
ufacturer perform the following checks every 24
months.
- Inspect the equipment for mechanical and functional
damage or deterioration.
- Ensure all user interface keys and accessories function
normally.
Note: Manufacturer use Index2 SpO2 simulator to ver-
ify operation of the pulse oximeter equipment.
Symptoms CorrectionsCheck points
SpO2 or pulse
rate cannot
displayed
Applied nger
improperly.
Place the nger prop-
erly and try again.
SpO2 is too low to
detect
Try again; go to consult
with your physician if
you are sure the device
works well.
SpO2 or pulse
rate are not dis-
played stably
Applied nger
improperly.
Place the nger prop-
erly and try again.
Finger is shaking or
body is moving. Keep body steady
No display
when button is
pressed
Batteries run down Replace with new
batteries
Batteries not
inserted correctly. Re-insert batteries
The display
disappears
suddenly
The device will auto
power o when it
gets no signal.
Normal
Low battery Replace with new
batteries
SpO2
Measuring range 35%~99%, (the resolution is 1%)
Accuracy 70%~99%: ±2%, Below 35~69%: unspecied
Optical Sensor The wavelength of red LED is 660 nm and
Infrared LED is 905/880 nm with maximum
optical output power of 4 mW/sr.
Pulse
Measuring range 30 bpm~250 bpm (the resolution is 1 bpm)
Accuracy ±3 bpm
Power source AAA × 2 (Alkaline)
Battery life Continually for 16 hours with two alkaline
batteries
Operating
Condition
Temperature: 5 (41 ~ 104°C~40°C °F °F),
Relative Humidity: 15-95% (non condensing),
Atmospheric pressure: 700hPa ~ 1060hPa,
Attitude: -1,280 to 12,000 feet (-390m to 3,658m)
Storage /
Transportation
Condition
Temperature: -25 ~ 158°C~+70°C(-13°F °F),
Relative humidity: 15-90%(non condensing),
Atmospheric pressure: 700hPa ~ 1060hPa,
Attitude: -1,280 to 12,000 feet (-390m to 3,658m)
Dimensions 63.5(L) × 34(W) × 35(H) mm
Weight About 37g (without the batteries)
Standards IEC60601-1-2, Class B, IEC60601-1, Type BF,
ISO80601-2-61, IEC60601-1-11
Type BF applied parts
IP Classication IP22: Protection against harmful ingress of water
and particulate matter
Attention
Serial number
Manufacturer
Date of manufacture
Authorized representative in the European
Community
Note:
- A description of the effect on displayed and transmitted
SpO2 and pulse rate:
- Data averaging: 4 seconds for SpO2; 8 seconds for pulse
rate.
- Data update delay: Less than 2 seconds.
- The oximeter is calibrated in the factory before sale.
There is no need to calibrate during its life cycle.
Note: If the unit does not work, return it to your
dealer. Under no circumstance should you
disassemble and repair the unit by yourself. SB220
www.rossmax.com
Fingertip Pulse Oximeter
Rossmax InnoTek Corp.
12F., No. 189, Kang Chien Rd., Taipei,
114, Taiwan.
CMC Medical Devices & Drugs S.L.
C/ Horacio Lengo Nº 18, CP 29006,
Málaga, Spain
WARNING: The symbol on this product means that it's an electronic product
and following the European directive 2012/19/EU the electronic products have
to be dispose on your local recycling centre for safe treatment.
IN0SB221000000013
Warranty Card
This instrument is covered by a 2 year guarantee from the date of purchase, batteries
and accessories are not included. The guarantee is valid only on presentation of the
guarantee card completed by the dealer confirming date of purchase or the receipt.
Opening or altering the instrument invalidates the guarantee. The guarantee does
not cover damage, accidents or non-compliance with the instruction manual.
Please contact your local seller/dealer or www.rossmax.com.
Customer Name: __________________________________
Address: _______________________________________
Telephone: _____________________________________
E-mail address: ___________________________________
Product Information: ______________________________
Date of purchase: _________________________________
Store where purchased:
______________________________________________
RI_IB_SB220_EN_
2Yr_TP_ver2128
Note:
1. The product is with a service life of 5 years in the course
of regular use.
2. If any serious incident (e.g. death) has occurred in
relation to the device should be reported to the
dealer, manufacturer, and the competent authority of
the Member State in which the user and/or patient is
established.
3. The text is subject to change without further notice.
EMC guidance and manufacturer’s declaration
Recommended separation distances between portable and mobile RF communications equipment and
the ME equipment
The Finger-tip pulse oximeter is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the Finger-tip pulse oximeter can help prevent elec-
tromagnetic interference by maintaining a minimum distance between portable and mobile RF communi-
cations equipment (transmitters) and the Finger-tip pulse oximeter as recommended below, according to
the maximum output power of the communications equipment.
Rated maximum output
power of transmitter / W
Separation distance according to frequency of transmitter / m
150 kHz to 80 MHz ,
d=[3.5/V1]√P
80 MHz to 800 MHz ,
d=[3.5/E1]√P
800 MHz to 2,5 GHz ,
d=[3.5/E1]√P
0.01 0.12 0.12 0.23
0.1 0.37 0.37 0.74
1 1.17 1.17 2.33
10 3.7 3.7 7.37
100 11.67 11.67 23.33
Declaration – electromagnetic emissions and immunity – for EQUIPMENT and SYSTEMS that are not LIFE-
SUPPORTING and are specied for use only in a shielded location
The Finger-tip pulse oximeter declaration – electromagnetic immunity
The Finger-tip pulse oximeter system is intended for use in the electromagnetic environment specied
below. The customer or the user of the Finger-tip pulse oximeter system should assure that it is used in
such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment-guidance
Conducted RF
IEC 61000-4-6 3 Vrms
150 kHz to 80 MHz 3V Portable and mobile RF communications
equipment should be used no closer to any part
of the EQUIPMENT or SYSTEM including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter. Interference may
occur in the vicinity of equipment marked with
the following symbol.
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to 2.5 GHz 3V/m
Declaration – electromagnetic immunity
The Finger-tip pulse oximeter system is intended for use in the electromagnetic environment specied
below. The customer or the user of the Finger-tip pulse oximeter system should assure that it is used in
such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment-
guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air ±6 kV contact
±8 kV air Floors should be wood, concrete
or ceramic tile. If oors are covered
with synthetic material, the
relative humidity should be at
least 30 %.
Electrical fast
transient/burst
IEC 61000-4-4
±2 kV for power sup-
ply lines
±1 kV for input/
output lines
±2 kV for power sup-
ply lines Mains power quality should be
that of a typical commercial or
hospital environment.
Surge IEC
61000-4-5
± 1kV dierential mode
± 2kV common mode
± 1kV dierential mode
± 2kV common mode
Mains power quality should be
that of a typical commercial or
hospital environment.
Voltage dips,
short interrup-
tions and voltage
variations on
power supply
input lines IEC
61000-4-11
<5% UT(>95% dip in
UT) for 0,5 cycle
40% UT(60% dip in UT)
for 5 cycles
70% UT(30% dip in UT)
for 25 cycles
<5% UT(>95% dip in
UT) for 5 s
<5% UT(>95% dip in
UT) for 0,5 cycle
40% UT(60% dip in UT)
for 5 cycles
70% UT(30% dip in UT)
for 25 cycles
<5% UT(>95% dip in
UT) for 5 s
Mains power quality should be
that of a typical commercial or
hospital environment. If the user
of the EQUIPMENT or SYSTEM
requires continued operation
during power mains interruptions,
it is recommended that the EQUIP-
MENT or SYSTEM be powered
from an uninterruptible power
supply or a battery.
Power frequency
(50/60 Hz)
magnetic eld
IEC 61000-4-8
3 A/m 3 A/m Power frequency magnetic elds
should be at levels characteristic of
a typical location in a typical com-
mercial or hospital environment.
Declaration – electromagnetic emissions
The Finger-tip pulse oximeter is intended for use in the electromagnetic environment specied below. The
customer or the user of the Finger-tip pulse oximeter should assure that it is used in such an environment.
Emission test Electromagnetic environment-guidanceCompliance
CE emissions CISPR11 Group 1 The Finger-tip pulse oximeter uses RF energy only for
its internal function. Therefore, its RF emissions are
very low and are not likely to cause any interference
in nearby electronic equipment.
RF emissions CISPR 11 Class B The Finger-tip pulse oximeter is suitable for use in all
establishments, including domestic establishments
and those directly connected to the public low-voltage
power supply network that supplies buildings used for
domestic purposes.
Harmonic emissions IEC 61000-3-2 Class A
Voltage uctuations/icker emis-
sions IEC 61000-3-3 Complies
Introduction
Rossmax Fingertip Pulse Oximeter SB220 is used
to measure arterial oxygen saturation (% SpO2) of
hemoglobin and pulse rate, an important indicator
of your respiratory function. It is non-invasive device
intended for spot-check of adult and pediatric whose
age is over 3 at home, hospital and clinics.
Attention: Consult the accompanying
documents. Please read this manual carefully
before use. Please be sure to keep this manual.
Installing Batteries
Error code for your reference
1. Use thumb to slide battery cover
out.
2. Insert or replace 2 “AAA” sized
batteries down with the correct
electrical polarity.
You need to replace the batteries
when:
1. Low battery icon appears on
display
2. The function button is pressed
and nothing appears on display.
Caution:
Batteries may leak or explode if
used or disposed of improperly. Remove batteries if the
device will be stored for long time. Do not use different
types or brands of batteries at the same time. Do not
mix fully charged and partially charged batteries at the
same time. The device will automatically shut down in
low battery.
SENSOR ERROR:
Er
Sensor cannot be detected,
return the device to your
local distributor or service
centre.
MEASURE ERROR:
Signals cannot be detected,
turn the device off and meas-
ure again.
Attaching the lanyard
1. Insert the narrow end of the
lanyard through the holder.
2. Draw the other end of the
lanyard through the loop
at the narrow end and
tighten.
How to use
1. Open the clip; press the Power On/Off button as .
2. Information of software version appears. Insert one
finger(left hand middle finger is recommended), nail
side up, into the finger opening of the pulse oximeter
as .
Note: If no finger insert, the device will auto shut off
after 8 seconds.
3. The display shows , pulse oximeter begins its
measurement.
Note: Make sure the finger is lying flat. Do not shake
and keep body steady during measurement.
4. Your SpO2 and pulse rate values will appear on the
screen after few seconds as .
Note: 1. Don’t remove your finger until the measurement
is completed.
2. While pulse strength is low, the reading will
flicker.
Cautionary Notes
- This device is to be operated by trained personnel only.
- The device has intended only for spot-checking, but not
medical result evaluation.
- This device is designed to determine the percentage of ar-
terial oxygen saturation of functional hemoglobin. Factors
that may degrade pulse oximeter performance or aect
the accuracy of the measurement include the following:
• Do not apply the pulse oximeter on the same arm as a
blood pressure cu, arterial catheter or infusion line(s).
• Excessive light, such as sunlight or direct home lighting.
• Not steady at the site of application (e.g. trembling).
• Moisture in the device.
• Improperly applied device.
• Finger is too large or too small to t into the device.
• Poor pulse quality.
• Venous pulsations.
• Anemia or low hemoglobin concentrations.
• Cardiogreen and other intravascular dyes.
• Carboxyhemoglobin.
• Methemoglobin.
• Dysfunctional hemoglobin.
• Articial nails or ngernail polish.
• On ngers with anatomical changes, oedemas, scars
or burns.
- Using the device for long periods may cause pain for
people with circulatory disorders. Reposition the device
at least once every 4 hours to allow the patient’s skin to
breath and to check patient’s condition regularly.
- Do not use the device near ammable or explosive gas
mixtures.
- Do not use the device during an MRI or CT scan, be used
no closer than 30 cm (12 inches) to any part of the SpO2
device, including cables specied by the manufacturer.
- The device may not work when circulation is reduced.
Warm or rub the nger, or re-position the device.
- This device is a precision electronic instrument and must
be repaired by qualied technical professionals. Field re-
pair of the device is not possible. Do no attempt to open
the case or repair the electronics. Opening the case may
damage the device and void the warranty.
- Do not overextend the device’s spring.
- A functional tester cannot be used to access the accu-
racy of a pulse oximeter monitor.
- Do not self-diagnose or self-medicate on the basis of
the measurements without consulting your doctor. In
particular, do not start taking any new medication or
change the type and/or dosage of any existing medica-
tion without prior approval.
- Do not look directly inside the housing during the meas-
urement. The red light and the invisible infra-red light in
the pulse oximeter are harmful to your eyes.
- This device is not intended for use by people (includ-
ing children) with restricted physical, sensory or mental
skills or a lack of experience and/or a lack of knowledge,
unless they are supervised by a person who has respon-
sibility for their safety or they receive instructions from
this person on how to use the device. Children should
be supervised around the device to ensure they do not
play with it.
- Neither of the displays for the pulse wave and pulse
bar allows the strength of the pulse or circulation to be
evaluated at the measurement site. Rather, they are ex-
clusively used to display the current signal variation at
the measurement site and do not enable reliable diag-
nostics for the pulse.
- The maximum temperature of sensors which the user
will touch might reach 43°C when operating in the 40°C
environment.
- The safety for user use in high-temperature environment
is measuring for 10 minutes, and turn it o for 20 min-
utes before measure again.
5. Press button shortly to reverse the display upside
down.
Note:
1. The SpO2 sensor and photoelectric receiving tube
should be arranged in a way with the subject’s arteriole
in a position there between.
2. Make sure the optical path is free from any optical
obstacles like rubberized fabric.
3. Excessive ambient light may affect the measuring
result. It includes fluorescent lamp, dual ruby light,
infrared heater, direct sunlight and etc.
4. Strenuous action of the subject or extreme
electrosurgical interference may also affect the
accuracy.
5. The device has a visual and audio signal when the
measurement of SpO 2 is lower than 90%.
Name/ Functions of each part
1. OLED display
2. Pulse strength
3. Pulse search icon
4. Remind icon
5. Battery indicator
6. Power On/O Button
7. Battery compartment
8. Pulse rate icon
9. SpO2 icon
1
2
3
4
5
67
9
8
Product specificaties
| Merk: | Rossmax |
| Categorie: | Hartslagmeter |
| Model: | SB220 |
Heb je hulp nodig?
Als je hulp nodig hebt met Rossmax SB220 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Hartslagmeter Rossmax
27 Maart 2024
Handleiding Hartslagmeter
- Hartslagmeter Garmin
- Hartslagmeter Medion
- Hartslagmeter BBB Cycling
- Hartslagmeter Beurer
- Hartslagmeter Bushnell
- Hartslagmeter Dexford
- Hartslagmeter Digi-tech
- Hartslagmeter Domyos
- Hartslagmeter Echowell
- Hartslagmeter Flow Fitness
- Hartslagmeter Fusion Sport
- Hartslagmeter Homedics
- Hartslagmeter IGPSport
- Hartslagmeter Iriver
- Hartslagmeter Lanaform
- Hartslagmeter Magellan
- Hartslagmeter Maxxus
- Hartslagmeter Medisana
- Hartslagmeter Mio
- Hartslagmeter Polar
- Hartslagmeter Pro-form
- Hartslagmeter Pyle
- Hartslagmeter Runtastic
- Hartslagmeter Sanitas
- Hartslagmeter Sigma
- Hartslagmeter Suunto
- Hartslagmeter Terraillon
- Hartslagmeter TomTom
- Hartslagmeter VirtuFit
- Hartslagmeter Omron
- Hartslagmeter Oregon Scientific
- Hartslagmeter Osynce
- Hartslagmeter Christopeit
- Hartslagmeter Lezyne
- Hartslagmeter Proficare
- Hartslagmeter BBB
- Hartslagmeter CicloSport
- Hartslagmeter Wahoo Fitness
- Hartslagmeter Ciclo
Nieuwste handleidingen voor Hartslagmeter
20 Februari 2024
9 Januari 2024
30 Oktober 2023
30 Oktober 2023
Oregon Scientific AH300E Talking Heart Rate Monitor Handleiding
16 Oktober 2023
Oregon Scientific AH300 Talking Heart Rate Monitor Handleiding
16 Oktober 2023
Oregon Scientific AH300A Talking Heart Rate Monitor Handleiding
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
14 Augustus 2023