Roland PDA120L Handleiding

Roland Niet gecategoriseerd PDA120L

Lees hieronder de 📖 handleiding in het Nederlandse voor Roland PDA120L (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 141 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Before using this unit, carefully read the leaet “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the

document(s) where it will be available for immediate reference.

Names of Parts

Hoop rubber Head

Tuning bolt

Shell Lug

Hoop

(rim)

Hand knob

Bracket

(PDA120L, PDA100L

only)

Output jack

* The illustration shows the PDA120L.

NOTE

Due to the characteristics of the materials used in the sensor, the

strike feel of the head and the sensitivity of the sensor may be

aected by changes in temperature and humidity.

Mounting on a Stand

PDA120L, PDA100L only

Tom holder

Loosen

Allowable diameter of mounting rod: 9–13 mm (3/8–9/16 inches)

Connecting to the Drum Sound Module

Using the included connection cable (stereo cable) or the

dedicated connection cable included with your drum sound

module, attach the pad to your drum sound module.

Connect the L-shaped plug of the connection cable to the pad’s

output jack.

Using a mono cable will NOT allow rim shots.

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

L-shaped

plug

I-shaped

plug

To Output jack

Example: Drum Sound

Module TD-17

Connection cable

(Accessory)

Recommended Parameter Settings

These are the recommended setting values for the trigger

parameters when using the PDA120LS, PDA120L, or PDA100L

with your drum sound module.

Choose these if “PDA120LS/PDA120L/PDA100L” is one of the

choices for “PAD TYPE” or “TRIG TYPE” on your drum sound

module.

If “PDA120LS/PDA120L/PDA100L” is not one of the choices, then

refer to the support information on the Roland

website.

http://roland.cm/trigger_prm

You might need to adjust the trigger parameters

depending on the conditions of use, such as the mounting

method or the position of the PDA120LS, PDA120L, or PDA100L.

For details on these settings, refer to the owner’s manual of your

drum sound module.

Adjusting the Head Tension

Before playing, you must adjust the pad tension rst.

If the head is too loose, the sensor might not work correctly,

or the sensor might be damaged. For stable operation, adjust

the head tension slightly tighter than the strike feel of a typical

acoustic drum.

NOTE

To avoid faulty operation, observe the following points.

5Adjust the head evenly so that it does not sag.

5Adjust the tuning bolts so that they are not loose.

1. Adjust each tuning bolt little by little, across the head

as indicated in the illustration.

Head

Tuning bolt

NOTE

Fully tightening a tuning bolt at only a single location produces

uneven tensioning, and correct playing dynamics may not

be achieved or may even cause malfunctions. Even tuning/

tensioning is very important.

2. Adjust the tightness of each tuning bolt so that the

head is tensioned evenly.

MEMO

5Head tension will not aect the actual tuning of the sound you

are playing. For that you need to adjust sound parameters in

the drum sound module you are using. For details, refer to the

owner’s manual of your drum sound module.

5Also, head tension may change depending on usage. Adjust

as needed.

Replacing the Head or Hoop Rubber

The performance of the head and/or hoop rubber will diminish

with use over time. If the head is torn or becomes too fatigued, or

impossible to tension correctly, then it should be replaced. If the

hoop rubber is worn out, it too can be replaced.

For replacement heads or to have the hoop rubber replaced,

please contact your dealer or a Roland service center.

Replacing the Head

NOTE

Applying excessive force to the sensors located under the head

can damage them and/or interfere with accurate triggering.

PDA120LS, PDA120L

Head

Hoop

Sensor

* The illustration shows the PDA120L.

PDA100L

Sensor

1. Remove all tuning bolts.

Go around and loosen each bolt a little at a time by turning it

counter-clockwise.

2. Remove the hoop and old head.

* Take care not to touch the sensor with your hand.

3. Place the new head and hoop on the shell.

4. Install all six tuning bolts.

5. Adjust the tension of the head.

Playing Methods

Head shot

Hit only the head of the pad.

Head shot

MEMO

For details on the sounds that are supported, refer to the owner’s

manual of your drum sound module.

Rim shot

Strike the head and the rim of the pad simultaneously.

A sound (rim sound) dierent than the head shot will be heard.

Rim shot

Head shot

Main Specications

Roland PDA120LS, PDA120L, PDA100L: V-Pad

PDA120LS PDA120L PDA100L

Shell 12 (diameter) x 4 (depth) inches

Wood shell

10 (diameter) x 4 (depth) inches

Wood shell

Head 2-ply mesh head

Triggers 2 (Head, Rim)

Connector Output jack

Allowable diameter of

mounting rod – 9–13 mm (3/8–9/16 inches)

Dimensions

345 (W) x 324 (D) x 125 (H) mm

13-5/8 (W) x 12-13/16 (D) x 4-15/16 (H)

inches

345 (W) x 380 (D) x 125 (H) mm

13-5/8 (W) x 15 (D) x 4-15/16 (H) inches

295 (W) x 330 (D) x 125 (H) mm

11-5/8 (W) x 13 (D) x 4-15/16 (H) inches

Weight 2.0 kg

4 lbs 7 oz

2.3 kg

5 lbs 2 oz

1.9 kg

4 lbs 4 oz

Accessories Owner’s Manual, Leaet “USING THE UNIT SAFELY,” Connection cable, Drum key

This document explains the specications of the product at the time that the document was issued. For the latest information, refer to

the Roland website.

Owner’s Manual

PDA120LS PDA120L PDA100L V-Pad English

When you need repair service, access this URL and nd your nearest

Roland Service Center or authorized Roland distributor in your country.

http://roland.cm/service

Roland Service Centers and Distributors

Product specificaties

Merk:	Roland
Categorie:	Niet gecategoriseerd
Model:	PDA120L

Heb je hulp nodig?

Als je hulp nodig hebt met Roland PDA120L stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Roland

Roland RCP800 Handleiding

9 April 2024

Roland HP605 Handleiding

9 April 2024

Roland FD-01A Handleiding

9 April 2024

Roland MDS-4KVX Handleiding

9 April 2024

Roland CY-12C Handleiding

9 April 2024

Roland JUNO-60 Handleiding

9 April 2024

Roland TB-303 Handleiding

9 April 2024

Roland VP-42H Handleiding

9 April 2024

Roland PD-100 Handleiding

9 April 2024

Roland JX-3P Handleiding

9 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024