Rode VideoMic Rycote Handleiding

Rode Microfoon VideoMic Rycote

Lees hieronder de 📖 handleiding in het Nederlandse voor Rode VideoMic Rycote (3 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
80Hz
VideoMicTM
Parts Guide
Mic Controls
quickstart
guide
VideoMicTM
www.rodemic.com
1. Foam windshield
2. Camera shoe mount
3. Battery cover
4. PAD switch (inside battery compartment)
warranty.rodemic.com/videomic
Scan the QR code to
register now, or visit
Don t FORGET’
to register for your
FREE ten year warranty!
The RØDE VideoMicTM features an integrated
shock mount based on RycoteÂŽ LyreÂŽ technology.
Constructed from a single piece of hard-wearing
thermoplastic, the LyreÂŽ provides superior acoustic
suspension to traditional elastic solutions,
and will never wear out, sag or snap.
RØDE SOUNDBOOTH
now for Broadcast mics
Hear and compare RØDE microphones
at www.rodemic.com/soundbooth or on your iPadÂŽ
5. LED power indicator
6. Power and HPF switch
7. Integrated Rycote ÂŽ LyreÂŽ suspension
8. 3.5mm dual mono output cable
The High Pass Filter (HPF ) is a low frequency cut-off setting, which you can use
to remove rumble, camera noise or other low frequency noise while recording.
Mic ON
using High Pass Filter
Mic ON
Flat setting
Battery OFF
Mic mute
6
7
8
LED power
indicator
0dB
-10d
B
-20dB
The next to the LED power indicator
On/Off switch will turn red when the
battery is running low. The mic will
work for approximately one hour once
the red indicator is lit, however with
reduced performance.
1. Turn the tightening ring counter-
clockwise to loosen the camera shoe
connection, before attaching to camera.
Securing the cable will
eliminate undesired noise
caused by cable movement.
The cable can be secured
in one of two orientations,
depending on the location
of your camera’s “Audio In”
socket.
See diagram for cameras 1
with mic socket on the .left
See diagram for cameras 2
with mic socket on the .right
2. Slide the camera-shoe into place on the
camera mount. When the mic is in place,
secure it by gently tightening the ring
clockwise.
3. Connect the VideoMic’s audio lead to
the camera’s “Audio In” or “Mic” socket,
and secure the cable in place using the
in-built cable clips (see below).
mounting to camera
securing the cable
PAD switchbattery
1
1
2
2
3
The VideoMic comes with a three-position
PAD switch which is located inside the battery
compartment.
The PAD provides a selectable 10 or 20db
reduction of the input sensitivity, reducing
the output level when recording loud sound
sources, so that the optimal level can be
achieved in a wide range of situations.
To change the battery, gently push
and slide the battery cover off. Insert a
standard 9V battery with the positive
(+) end upwards.
The VideoMic uses a standard 9V
battery. With a good quality Alkaline
or Lithium battery, the VideoMic will
run for up to 100 continuous hours. We
recommend you remove the battery
if storing your VideoMic for extended
periods without use.
+
–
Push the cable in from the bottom.


Product specificaties

Merk: Rode
Categorie: Microfoon
Model: VideoMic Rycote

Heb je hulp nodig?

Als je hulp nodig hebt met Rode VideoMic Rycote stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Rode

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon