Remington RM4218 Handleiding

Remington Zaagmachine RM4218

Lees hieronder de 📖 handleiding in het Nederlandse voor Remington RM4218 (88 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/88

769-09654 / 00 01/14

Operator’s Manual

2-Cycle Chain Saw

RM4214 / RM4216 /

RM4218

TABLE OF CONTENTS

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Oil and Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Starting and Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

All information, illustrations, and specifications in this manual are based

on the latest product information available at the time of printing. We

reserve the right to make changes at any time without notice.

DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.

For assistance regarding the assembly, controls, operation or

maintenance of the unit, please call the Customer Support Department

at 1-866-206-2707 in the United States or 1-877-696-5533 in Canada.

Additional information about the unit can be found on our website at

www.remingtonpowertools.com.

For service, please call the Customer Support Department to obtain

a list of authorized service dealers near you. Service on this unit,

both within and after the warranty period, should only be performed

by an authorized and approved service dealer. When servicing, use

only identical replacement parts.

SAVE THESE INSTRUCTIONS

SERVICE

IMPORTANT: Read this manual thoroughly before using this product. Follow all instructions.

SAFETY

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and

4443), Oregon and Washington require, by law that certain internal

combustion engines operated on forest brush and/or grass-covered

areas be equipped with a spark arrestor, maintained in effective

working order, or the engine be constructed, equipped and

maintained for the prevention of fire. Check with your state or local

authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine.

This unit is factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753-08106 Muffler Assembly.

Read the operator’s manual and follow all warnings and safety

instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

SYMBOL MEANING

WARNING: Signals a SERIOUS hazard.

Failure to obey a safety WARNING signal CAN result in

serious injury to yourself or to others.

CAUTION: Signals a MODERATE hazard.

Failure to obey a safety CAUTION signal MAY result in

property damage or injury to yourself or to others.

The purpose of safety symbols is to attract your attention to

possible dangers. The safety symbols, and their explanations,

deserve your careful attention and understanding. The safety

warnings do not by themselves eliminate any danger. The

instructions or warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to the

operation or maintenance of the equipment.

DANGER: Signals an EXTREME hazard.

Failure to obey a safety result inDANGER signal WILL

serious injury or death to yourself or to others.

CALIFORNIA PROPOSITION 65

WARNING:This product contains a chemical

known to the state of California to cause cancer, birth defects

or other reproductive harm.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and approved

for the storage of such materials.

• Always stop the engine and allow it to cool before filling the

tank. Never remove the fuel tank cap or add fuel when the

engine is hot. Always loosen the fuel tank cap slowly to relieve

any pressure in the tank before fueling.

• Always mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. DO NOT smoke.

• Never operate the unit without the fuel cap securely in place.

• Avoid creating a source of ignition for spilled fuel. Wipe up any

spilled fuel from the unit immediately, before starting the unit.

Move the unit at least 30 ft. (9.1 m) from the fueling source and

site before starting the engine. DO NOT smoke.

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can kill. Operate this unit only in a well

ventilated outdoor area.

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING: Use caution when handling fuel.

Gasoline is highly flammable and its vapors can explode if

ignited. Take the following precautions:

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls and

proper use of the unit. Know how to stop the unit and disengage

the controls quickly.

• Do not operate this unit when tired, ill or under the influence of

alcohol, drugs or medication.

• Never allow children to operate the unit. Never allow adults to

operate the unit without proper instruction.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check for

fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

• Be aware of risk of injury to the head, hands and feet.

• Carefully inspect the area before starting the unit. Remove

rocks, broken glass, nails, wire, string and other objects that

may be thrown or become entangled with the unit.

• Clear the area of children, bystanders and pets; keep them

outside a 50-foot (15 m) radius, at a minimum. Even then, they are

still at risk from thrown objects. Encourage bystanders to wear

eye protection. If you are approached, stop the unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using the unit.

WARNING: When using the unit, all safety rules

must be followed. Please read these instructions before

operating the unit in order to ensure the safety of the

operator and any bystanders. Please keep these

instructions for later use.

WHILE OPERATING

• Wear safety glasses or goggles that meet current ANSI Z87.1

standards and are marked as such. Wear ear/hearing protection

when operating this unit. Wear a face mask or dust mask if the

operation is dusty. Use a hard hat or other type of safety helmet.

• Wear safety boots and protective gloves. Wear heavy, snug-

fitting clothes, including long pants and a long-sleeve shirt. Do

not wear loose clothing, jewelry, short pants, sandals or go

barefoot. Secure hair above shoulder level.

• Make sure the saw chain is not in contact with anything before

starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting and Stopping.

• Use the right tool. Only use this tool for its intended purpose: to

cut wood. Do not use the unit for cutting plastic, masonry or

other non-wood building materials. Only use the unit as

described in this manual.

• Keep all body parts away from the saw chain when the unit is

running. Do not touch or try to stop moving parts.

• Do not touch the engine or muffler. These parts get extremely hot

from operation, even after the unit is turned off.

• Do not operate the unit faster than the speed needed to do the job.

Do not run the unit at high speed when not in use.

• Do not force the unit, especially near the end of a cut. It will do a

better, safer job when used at the intended rate.

• Always turn the engine off when operation is delayed, when

setting the unit down or when carrying the unit from one location

to another. Make sure all moving parts come to a complete stop.

• Carry the unit by the front handle with the muffler positioned

away from the body and the guide bar positioned to the rear.

Cover the guide bar and saw chain with the scabbard when

carrying the unit.

• If you strike or become entangled with a foreign object, stop the

unit immediately and check for damage. Do not operate the unit

before repairing damage. Do not operate the unit with loose or

damaged parts.

• Use only original equipment manufacturer (OEM) replacement

parts and accessories for this unit. These are available from your

authorized service dealer. Use of any other parts or accessories

could lead to serious injury to the user, or damage to the unit,

and void the warranty.

• Keep the unit clean. Carefully remove vegetation and other

debris that could block moving parts.

• To reduce fire hazard, replace a faulty muffler and spark arrestor.

Keep the engine and muffler free from grass, leaves, excessive

grease or carbon build up.

• If the unit starts to vibrate abnormally, stop the unit immediately.

Inspect the unit for the cause of the vibration. Vibration is

generally an indicator of trouble.

• Keep the work area clean. Cluttered areas invite injuries. Do not

start cutting until the work area is clear and free from

obstructions. Make sure there is secure footing and a planned

retreat path from falling trees or branches.

• Do not cut near electrical cables or power lines. Keep at least 50

feet (15 m) away from all power lines.

• For safer, more effective performance, make sure the guide bar

and chain are properly cleaned, lubricated, tightened and

sharpened. Check the guide bar and chain at frequent intervals

for proper adjustment.

• When cutting a limb that is under tension, use extreme caution.

When the tension is released, the limb could spring back and

strike the operator, causing severe injury or death.

• Use extreme caution when cutting small-sized brush and

saplings, as slender material may catch the saw chain and be

whipped toward the operator or pull the operator off balance.

• This saw is classified by UL as a Class 1C saw in accordance

with CSA Z62.1-03. It is intended for infrequent use by

homeowners, cottagers and campers, and for general

applications such as clearing, pruning, cutting firewood, etc. It is

not intended for prolonged use. If the intended use involves

prolonged periods of operation, this may cause circulatory

problems in the user’s hands due to vibration.

• Do not operate the unit in a tree or on a ladder unless

specifically trained to do so.

• Never remove, modify or make inoperative any safety device

furnished with the unit.

• Do not use the unit in the presence of flammable liquids or gases.

• Do not attempt operations beyond the operator’s capacity or

experience.

• Do not operate a unit that is damaged, improperly adjusted or

not completely and securely assembled. Make sure moving

parts stop when the unit is turned off. Do not use the unit if it

does not turn on and off properly. Have defective parts replaced

by an authorized service dealer.

KICKBACK SAFETY

Understanding Kickback

A basic understanding of kickback can help reduce or eliminate the

element of surprise and the chance of kickback-related injury.

Sudden surprise contributes to accidents.

•Rotational Kickback can happen when the upper tip of the

guide bar contacts an object while the chain is moving (Fig. A).

This can cause the chain to dig into the object and momentarily

stop moving. The guide bar is then kicked up and back toward

the operator in a lightning-fast reverse reaction.

•Linear Kickback can happen when the wood on either side of a

cut closes in and pinches the moving saw chain along the top of

the guide bar (Fig. B). This can cause the chain to instantly stop.

The chain force is then reversed, causing the saw to move in the

opposite direction, sending the saw straight back toward the

operator.

•Pull-In can happen when the moving chain on the bottom of the

guide bar hits a foreign object inside the wood. This can cause

the chain to suddenly stop. The saw is then pulled forward and

away from the operator, which could potentially result in the loss

of control of the saw.

WARNING: Kickback may occur when the

nose or tip of the guide bar touches an object, or when the

wood closes in and pinches the saw chain in the cut. In

some cases, tip contact may cause a lightening-fast

reverse action, kicking the guide bar rapidly back to wards

the operator. Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly back towards the

operator. Either of these reactions may cause a loss of

control over the saw, which could result in serious injury to

the user. Contact with foreign objects within the wood can

also induce a loss of chain saw control.

Product specificaties

Merk:	Remington
Categorie:	Zaagmachine
Model:	RM4218

Heb je hulp nodig?

Als je hulp nodig hebt met Remington RM4218 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Remington

Remington RM4214CS Handleiding

16 April 2023

Remington RM1025P Handleiding

23 Maart 2023

Remington RM1425 Handleiding

2 Februari 2023

Remington RM1025SPS Handleiding

29 Januari 2023

Remington RM4214 Handleiding

26 Januari 2023

Remington RM4618 Handleiding

13 Januari 2023

Remington RM4218 Handleiding

19 November 2022

Remington RM4216CS Handleiding

21 Oktober 2022

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx Nitro WX542.9 Handleiding

26 April 2024

Fieldmann FZP 25410-B Handleiding

15 April 2024

Milwaukee M18 BJS Handleiding

10 April 2024

Rona Standard Plus-C Handleiding

10 April 2024

Rona Profi-C Handleiding

10 April 2024

Milwaukee SCS 65 Q Handleiding

10 April 2024

Milwaukee M12 BS Handleiding

10 April 2024

Milwaukee M18 FMCS66 Handleiding

10 April 2024

Milwaukee M18 BSX Handleiding

10 April 2024

Bavaria By Einhell BFS 800E Handleiding

9 April 2024