Rane SEQ 30S Handleiding
Rane
Niet gecategoriseerd
SEQ 30S
Bekijk gratis de handleiding van Rane SEQ 30S (5 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 5.0 sterren uit 2 reviews. Heb je een vraag over Rane SEQ 30S of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/5
Manual-1
OPERATORS MANUAL
QUICK START
If this is your first equalizer, please do yourself and
your speakers a favor and read at least the first five
pages. “An ounce of prevention...,” and all that.
The SEQ 30S is a stereo equalizer, so adjusting any
slider affects both channels simultaneously. Begin by
setting all sliders to their center detent (0 dB), and the
INPUT LEVEL to its center detent (0 dB). Try to make
more cuts than boosts. After equalizing, use the EQ
switch to compare equalized and non-equalized signal.
While EQ is switched to ACTIVE (out), adjust the
INPUT LEVEL to the same level as when EQ is
switched to BYPASS (in).
You may use either the XLR or ¼" connectors for
Inputs or Outputs. Connect only one INPUT type per
channel. The XLR and ¼" TRS inputs do not sum. You
may, however, use both types of OUTPUTS simulta-
neously if desired.
WEAR PARTS: This product contains no wear parts.
SEQ 30S
STEREO GRAPHIC EQUALIZER
Manual-2
EQ BYPASS switch
When pressed to BYPASS, the filter
sliders have no effect. Since actual unity
gain depends on varying slider settings,
use the BYPASS switch to determine
the unity gain position of the INPUT
LEVEL control by comparing ACTIVE
and BYPASS volumes.
Filter level slide controls
Each of these sliders control the
output level of both channels of the 30
bandpass filters. Center position is
grounded for guaranteed flat response.
INPUT LEVEL control and indicators
This controls the overall level. 0 dB gain is reached at the center detent with all
sliders centered at their 0 dB detents. Set the INPUT LEVEL to give equal volumes
with the EQ switched to ACTIVE or BYPASS, after setting the sliders (see EQ
BYPASS switch below). Apply sufficient signal to the input to occasionally light
the +4 dBu indicator. Flashing of the OL (overload) LED during peaks can be
avoided by turning the INPUT LEVEL or boosted Filters down.
Manual-3
POWER switch and LED
Your basic, straightforward power
switch. When the yellow LED is lit, the
SEQ 30S is ready to go.
Cable Wiring
In agreement with IEC and AES/
ANSI standards, XLR wiring conven-
tion is pin 2 Positive (hot), pin 3
Negative (cold), and
pin 1 Signal ground (for unbalanced
use). Pin 1 and the connector case or
shell are tied to chassis ground.
LEFT & RIGHT OUTPUTS
Use either the Balanced XLR or the
Unbalanced ¼" TS jacks. Using both
types of Outputs are permissible to
drive two devices, such as an amplifier
and a recorder.
LEFT & RIGHT INPUTS
Choose between the balanced XLR
or the balanced/unbalanced ¼" TRS
jacks, but only use one. Inserting a ¼"
TS jack will work—however—always
use balanced lines especially when
connecting cables over 10 feet in length.
Consult the Sound System Interconnec-
tion RaneNote located later in this
booklet.
Product specificaties
| Merk: | Rane |
| Categorie: | Niet gecategoriseerd |
| Model: | SEQ 30S |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane SEQ 30S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Rane
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
Handleiding Niet gecategoriseerd
- Linn
- Coleman
- DoubleSight
- Sennheiser
- Rexel
- Cres Cor
- Acros
- Vivo
- Powerplus
- Boss
- Mac Audio
- Econ Connect
- Loewe
- Celestion
- Adviti
Nieuwste handleidingen voor Niet gecategoriseerd
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025